makro Pointer User Manual

www.makrodetector.com

User Manual

Device Introduction

Battery Compartment

LED Flashlight

360° Detection Tip

On / Off

Speaker

Control Unit

Vibration / Audio & LED

Sensitivity Control

IP Rating:

IP67 - Dust resistant and waterproof up

to 1 meter depth.

A) To install the battery, twist and remove the fastener marked with
number 1.

B) To remove the control unit marked with number 2 from the device, pull
WITHOUT TWISTING.

C) Insert the battery facing downwards paying attention to plus (+) and
minus (-) poles. The device will not work if the battery is not installed
correctly.

D) To mount the control unit (2) back on the device, align the contact pins
and the notches marked with number 3 and push to snap in. DO NOT
TWIST THE CONTROL UNIT!

E) Twist the fastener (1) and do not leave it loose to secure a water tight
seal.

Battery Installation

12

Battery

3

Turning on the Device

Press and release the Green on/off (+) button once.
The LED will light up and a long warning tone will be
heard. Makro Pointer is ready for use. Be sure there are

no metal objects around at start up.

Mode Change

Press the Red (-) button for 3 seconds. A short warning
tone will be heard. The device will switch from the

audio mode to the vibration mode. When pressed
and held again, it will switch to the audio and vibration mode. If
pressed again, it will revert back to the audio mode. A short
warning tone will be heard with each mode change. Makro
Pointer will start at the same setting the next time you start up
the device.

Sensitivity Increase

Double click the Green on/off (+) button to increase

sensitivity. Sensitivity has 4 levels. The factory preset

setting is level 3. The device indicates the sensitivity
level with the number of warning tones. Makro Pointer will start
at the last adjusted sensitivity level at start up.

Turning off the Device

Press and hold the Green on/off (+) button. Six (6)

short warning tones will be heard and the device will

turn off.

Detection Tip

Makro Pointer's detection
area is between the tip and

the hand grip. The coil
provides 360° detection. This helps you to locate targets quickly
and easily in the hole. If you hold the device horizontally, you can
scan a larger area. This allows you to cover a broader area to
quickly reach your target.

Sensitivity Decrease

Double click the Red button to lower sensitivity.
Sensitivity level is indicated by the number of
warning tones. Makro Pointer will start at the last

adjusted sensitivity level at start up.

Detection

Tip

LED Flashlight

Press the Red button once to turn it on, press again to
turn off. Makro Pointer will start at the same setting at
start up.

Low Battery Indicator

When the battery is low Makro Pointer will give 5 short-long
beeps at the start up. The device may continue to work for a
short period of time.

Coil Interference Blocking

When it is switched off, it disconnects the coil's magnetic transmission
and eliminates interference with another metal detector. This also
prevents the device from being detected as a target.

Replaceable Hard-Shell Cases

Makro Pointer comes with two hard-shell cases. One of the cases is
also designed to allow for digging.

Usage

When a target is detected, Makro Pointer will produce an audio
and/or vibration alert. The rate of the pulsing audio or vibrations
will increase as it gets closer to the target and it will decrease as it is
moved away.

TECHNICAL SPECIFICATIONS

Working Frequency
Metal Detection
Sensitivity
Coil Interference Blocking
Dimensions

Detection Tip
Weight

Working Temperature
Battery
Battery Life

11.6KHz
Audio and / or vibration alert
4 levels manual
Yes

9.4”x1.9”x1.9” (24 x 4.8 x 4.8cm) including the
hard-shell digger case

3.7'' (9.3cm)

8.3 oz (235 gr) including the battery and
hard-shell digger case

-4°F / +122°F (-20°C / +50°C)
9V Alkaline Battery
Up to 30 Hours

:
:
:
:
:

:
:

:
:
: