n
450
630
mm
mm
(17-314")
(24-3/4")
MODEL
MODEL
Equipped with electric brake
INSTRUCTION MANUAL
UH4510A
UH6310A
SPECIFICATIONS
MODEL
UH4510A
____
UH6310A
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country
Effective cutting
blade length
450
mm
[
17.314")
630
mm
(24-314")
Strokes
per
minute
1.800
1,800
Dimensions Net
IL
x W x
825
mm
x
mm
180
x
180
(32-112" x 7-118" x 6-518")
1,000
(39-318'' x 7.118" x 6-518")
to
country.
mm
mm
HJ
x
170
x
170
mm
mm
weight
3.2
(7.0
3.4
(7.5
kg
Ibs)
kg
IbsJ
IM
PO
RTANT
SAFETY
WARNING
-
TO REDUCE THE RISK
INSTRUCTIONS
(For
All
Tools)
OF
INJURY, BASIC
SAFETY PRECAUTIONS SHOULD BE OBSERVED. INCLUDING
THE FOLLOWING:
READ AND FOLLOW ALL INSTRUCTIONS.
DRESS PROPERLY - Do not wear loose clothing or jewelry. They can be
1.
caught
sturdy gloves is recommended.
STAY ALERT
2.
operate trimmer when fatigued.
DANGER
3.
FROM
Do not attempt to remove cut material nor hold material to be cut when
blades are moving. Make sure trimmer is switched off and unplugged when
clearing jammed material from blades. Do not grasp the exposed cutting
blades or cutting edges of trimmer.
CAUTION
WARNING
4.
trimmer
extension cords marked “for use with outdoor appliances” having electrical rating not less than rating of trimmer. Do not use damaged extension
cords. Inspect cords periodically and replace
Never carry trimmer by cord. Do not yank cord to disconnect from receptacles. Keep cord away from heat, oil, and sharp edges.
KEEP CHILDREN AWAY
5.
extension cord. Keep children a safe distance from work area.
USE TRIMMER PROPERLY
6.
growth, and the like, described
trimmer. Do not cut grass and weeds
DON’T OVERREACH
7.
ing and balance at all times.
AVOID UNINTENTIONAL STARTING
8.
trimmer, be sure trimmer switch is off. Don‘t carry trimmer with finger on
switch.
AVOID LOCKING TRIMMER SWITCH ON
9.
fasten the switches
DISCONNECT (UNPLUG) TRIMMER FROM POWER SUPPLY
IO.
use. Before servicing, cleaning, and the like.
2
in
moving parts. Use safety glasses and nonskid footwear. Use of
-
Watch what you are doing - use common sense. Do not
-
RISK
BLADES
-
Blades coast after turn off.
-
TO REDUCE THE RISK
in
rain,
in
wet locations, or on wet hedges of shrubbery. Use only
OF
CUT
-
Keep both hands on handles when power is on.
-
Do not permit children to contact trimmer or
-
Use only for trimming the type of shrub,
in
OR
STAND ON UNSTABLE SUPPORT - Keep good foot-
so
as to stay
-
KEEP
OF
ELECTRIC SHOCK - Don’t use
if
damaged.
the operating instructions. Do not abuse
with
this trimmer.
OF
TRIMMER - Before plugging in
-
Never attempt to tape, wire or
in
the ON position.
HANDS AWAY
Do
not abuse cord.
-
When not
in
Total Length
-
AWG
Contact Makita Authorized or Factory Service Center if a proper extension
cord cannot be found.
15.
Inspect blades periodically and replace before operation if damaged.
16.
Hold the tool firmly
17. Do not leave the tool running. Operate the tool only when hand-held.
18.
Attention! Do not expose this tool to rain.
The tool must not be left outdoors and
19.
Be cautious not to cut through the supply cable while trimming. Pull plug
immediately if the supply cable be damaged or cut.
20.
When not
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source
for the tool can result in SERIOUS INJURY to the user
the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source
voltage less than the nameplate rating is harmful
in
of
Cord
in Feet
Size
of
Cord
with
both hands.
use, be sure to cover the blades
25
18
with
voltage greater than that specified
50
I
1
16 16
it
must not be used when wet.
with
to
100
150
14
the blade guard.
-
as well as damage to
the motor.
with
SAVE THESE INSTRUCTIONS.
3
Installing grip
Attach the grip onto the grooves in the
tool side and secure with the two screws.
WARN
I
NG
:
DO
NOT USE WITHOUT GRIP.
Hook
When using an extension cord, secure
to
the tool‘s cord with the hook provided.
Attach the hook about 100-200 mm
8”)
from the extension cord connector.
This will help prevent unintentional disconnection.
Switch
action
To prevent the trigger from being accidentally pulled,
as
a
safety feature.
To start the tool, press the lock-off button
in and pull the trigger.
to
stop.
a
lock-off button
Release
(4”-
is
provided
the trigger
it
1
I
I
Cord connector
Power cord
1
Extension cord
CAUTION
Before plugging in the tool, always check to
and returns to the
4
:
“OFF”
position when released.
see
that the trigger switch actuates properly
Operation
Refer to the Important Safety Instructions
before operation.
Do
not attempt to cut branches thicker
than
12
mm
(15/32")
diameter with this
trimmer. These should first be cut with
shears down to the hedge trimming level.
Hold
the trimmer with both hands and
move it in front of your body.
When operating the trimmer, keep extension cord behind trimmer. Never drape
it
over hedge being trimmed.
I
Sturdy
gloves
To
cut a hedge top evenly,
a
string or cord
to
trim along it, using
and
at
line.
it
helps to
tie
the desired hedge height
it
as
a
reference
5
To cut a hedge side evenly,
i
it
helps to cut
from the bottom upwards.
Trim boxwood or rhododendron from the
for
a
base toward the top
nice appearance
and good job.
CAUTION
0
Be careful not to accidentally contact a metal fence or other hard objects while trim-
:
ming. The blade will break and may cause serious injury.
0
Do
not
attempt to trim too much
0
Overreaching with a hedge trimmer, par-
ticularly from
a
ladder,
is
at
a
time, or malfunction of the tool may result.
extremely dangerous. Don’t work from anything wobbly or unfirm.
6
MAINTENANCE
CAUTION
Always be sure that the tool
inspection and maintenance.
Blade maintenance
After operation, clean off the blades (both
sides) with
blades with
light machine oil.
After use
When storing the tool, use the convenient
hole in the bottom of the tool handle to
hang the tool on
:
is
switched off and unplugged before attempting to perform
a
stiff brush. Then wipe the
a
cloth and coat them with
a
wall from a nail or hook.
a
The tool will stop when the carbon brushes wear to
certain length. When this occurs,
both carbon brushes should be replaced.
To
maintain product SAFETY and RELlABl LITY, repairs, carbon brush inspection and
replacement, any other maintenance or adjustment should be performed by Makita
Authorized or Factory Service Centers, always using Makita replacement parts.
7
ACCESSORIES
CAUTION
These accessories or attachments are recommended for use with your Makita tool specified in this
manual. The use of any other accessories or attachments might present
accessories or attachments should be used only in the proper and intended manner.
:
a
risk
of
injury to persons. The
0
Blade
cover
Part
No.
414247-4
(For model UH4510A)
Part No. 414248-2
(For model UH6310A)
Shear
blade
No.
assembly
125009-2
Part No. 125008-4
(For model UH4510A)
Part
(For model UH6310A)
Hook
Part No. 158024-
1
8
Mar-13
'89
US
@-
I
HEDGE TRIMMER
450
mm
(17-3/4")
630
mm
(24-3/4")
Model
Model
UH4510A
UH6310A
Note: The switch and other part configurations
may differ from country
to
country.
9
MODEL UH4510A. UH6310A
I;,',"
AtD
DESCRIPTION
MACHINE
~
1
1
2
3
4
5
6
7
8
Y
11
13
14
15
16
17
18
19
20
21
Note The Switch and other
Housing
1
Sponge
1
Switch
1
Cord
1
Cord
1
Strain
Pan
2
Switch Lever
1
1
Lock
1
Compression
1
P,"
1
Flat
1
Gear
1
Crank
I
Sponge
1
Ball
Terminal
1
Fdd
1
ARMATURE ASSEMBLY
1
(With
-
Guard
Relief
Head
Off Button
10
Washer 10
68
Bearing
Item
Sel
(With
Item
Seal
Screw
Seal
Base
part
261
M4x18 (With Washerl
Spring
3
608L8
18 & 21 231
specifications may differ from countrv to countrv
"",M
MACHINE
~
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
-
DESCRIPTION
1
Fan
70
1
Bail
Bearing
2
Receptacle
2
Carbon
1
Housing
5
Tapping
1
Name
3
Pan
Head
1
Grip
27
2
Pan
Head
1
SHEAR BLADE ASSEMBLY
4
Pan
Head
1
Pan
Head
1
Guard
1
Hex
Nut
1
Bottom
2
Tappmg
-
Brush
Screw
Plate
Cover
Screw
6OYLB
Sleeve
Sei
fWith
Screw
Screw
Screw
Screw
M4- 10
lfem
11
4x20
M5x55 [With Washerl
M5x20 lWith Washerl
M5x16 IWNth Washerl
M4xl2
4x14
Mar -13-'8Y US
10
MAKITA
LIMITED
ONE
YEAR WARRANTY
Warranty
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita
replace) without charge.
This Warranty does not apply where:
0
repairs have been made or attempted by others:
0
repairs are required because of normal wear and tear:
0
The tool has been abused, misused or improperly maintained;
0
alterations have been made to the tool.
IN
NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,
AFTER THE ONE-YEAR TERM
This Warranty gives you specific legal rights, and
state to state. Some states do not allow the exclusion or Limitation of incidental or consequential
damages,
so
limitation on how long an implied warranty lasts,
P
the above limitation or exclusion may not apply to you. Some states do not allow
OF
THIS WARRANTY.
Policy
will
repair (or at our option,
you
may also have other rights which vary from
so
the above Limitation may not apply to you.
-€hutaK
11-8,3-chome, Sumiyoshi-cho.
883664-065
-
wan&b.Ltd.
Anjo,
Aichi
446,
Japan
PRINTED
IN JAPAN
1990
- 3 -
N
Loading...