Makita MT602, MT604 User Manual

INSTRUCTION MANUAL

Drill

MT602
MT603
MT604

DOUBLE INSULATION

WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

1

004259

ENGLISH

SPECIFICATIONS

Model MT602 MT603 MT604

Capacities

No load speed (min-1) 3,000 0 - 3,000 0 - 3,000

Overall length 228 mm 228 mm 234 mm

Net weight 1.2 kg 1.2 kg 1.2 kg

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Note: Specifications may differ from country to country.

Safety class /II

Symbols

The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.

Intended use
The tool is intended for drilling in wood, metal and
plastic.

Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.

For European countries only
Noise and Vibration

The typical A-weighted sound pressure level is 78 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).

The typical weighted root mean square acceleration
value is 7 m/s
These values have been obtained according to

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.

Wear ear protection.

2

.

Steel 10 mm 10 mm 10 mm

Wood 25 mm 25 mm 25 mm

END201-2

EN60745.

EC-DECLARATION OF CONFORMITY

Model; MT602, MT603, MT604

We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with

ENE032-1

ENF002-1

ENG004-2

Council Directives, 2004/108/EC, 98/37/EC.

000230

Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.

SAVE THESE INSTRUCTIONS.

Work area safety

1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

CE2006

Tomoyasu Kato

Director

ENH101-7

GEA001-3

2

operating a power tool. Distractions can cause
you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.

Personal Safety

9. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

10. Use safety equipment. Always wear eye
protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.

11. Avoid accidental starting. Ensure the switch is
in the off-position before plugging in. Carrying
power tools with your finger on the switch or
plugging in power tools that have the switch on
invites accidents.

12. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

13. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

14. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.

15. If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly used.

Use of these devices can reduce dust-related
hazards.

Power tool use and care

16. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

17. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.

18. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

19. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

20. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

21.

Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

22. Use the power tool, accessories and tool bits

etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use

of the power tool for operations different from
those intended could result in a hazardous
situation.

SERVICE

23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

24. Follow instruction for lubricating and

changing accessories.

25. Keep handles dry, clean and free from oil and
grease.

GEB002-2

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product

3