Makita HRU01 Instruction Manual

INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES

IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.

Cordless String Trimmer Coupe herbe sans-fil Desbrozadora Inalámbrica

HRU01

012857

ENGLISH (Original instructions)

SPECIFICATIONS

Model HRU01

High 0 - 7,000 /min

No load speed (RPM)

Low 0 - 5,100 /min

Overall length 1,720 mm (67-3/4")

Cutting diameter with nylon cutting head 300 mm (11-3/4")

Net weight 5.1 kg (11.2 lbs)

Rated voltage D.C. 36 V

Standard battery cartridge(s)

Warning: Use only the battery(ies) described.

BL3622A / BL3626

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

USB099-3

IMPORTANT SAFETY INSTRUCTIONS

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

General instructions

1. Do not allow persons unfamiliar with the string trimmer or these instructions to operate the tool. String trimmers are dangerous in the hands of untrained users.

2. Be sure that anyone who is to operate the string trimmer has first read the instruction manual.

3. Use the string trimmer with the utmost care and attention.

4. Operate the string trimmer only if you are in good physical condition. Perform all work calmly and carefully. Use common sense and keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.

5. Never operate the string trimmer when tired, feeling ill or under the influence of alcohol or drugs.

6. Avoid accidentally starting:

− Ensure the switch is in the off position before installing the battery pack. Inserting the battery pack into the string trimmer with the switch on invites accidents.

− Carrying the string trimmer with your finger on the switch invites accidents.

7. The string trimmer should be switched off immediately if it shows any signs of abnormal operation.

8. Disconnect the battery from the string trimmer before making any adjustments, changing accessories or storing. Such preventive safety measures reduce the risk of starting the sting trimmer accidentally.

9. Don't force the tool. it will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

10. Don't overreach. Keep proper footing and balance at all times.

Intended use of the tool

1. Use right tool. The cordless string trimmer is only intended for cutting grass and light weeds. It should not be used for any other purpose such as edging or hedge cutting as this may cause injury.

Personal protective equipment

1. Dress Properly. The clothing worn should be functional and appropriate, i.e. it should be tight-fitting but not cause hindrance. Do not wear either jewelry or clothing which could become entangled with bushes or shrubs. Wear protective hair covering to contain long hair.

2. In order to avoid either head, eye, hand or foot injuries as well as to protect your hearing the following protective equipment and protective clothing must be used during operation of the equipment.

010820

3. Always wear a helmet where there is a risk of falling objects. The protective helmet is to be checked at regular intervals for damage and is to be replaced at least every five years. Use only approved protective helmets.

4. The visor of the helmet (or alternatively goggles) protects the face from flying debris and stones. During operation of the tool always wear goggles, or a visor to prevent eye injuries.

Wear adequate noise protection equipment to avoid hearing impairment (ear muffs , ear plugs etc.).

010821

6. Work overalls protect against flying stones and debris. It is strongly recommended that the user wears work overalls.

7. Special gloves made of thick leather are part of the prescribed equipment and must always be worn during operation of the tool.

8. When using the tool, always wear sturdy shoes with a nonslip sole. This protects against injuries and ensures a good footing.

Electrical and battery safety

1. Avoid dangerous environment. Don't use the tool in damp or wet locations or expose it to rain. Water entering the tool will increase the risk of electric shock.

2. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

3. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

4. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

5. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, seek medical help. Liquid ejected from the battery may cause irritation or burns.

6. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions.

7. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

Starting up the tool

360°

012858

1. Make sure that there are no children or other people within a working range of 15 meters (50 ft), also pay attention to any animals in the working vicinity. Otherwise stop using the tool.

2. Before use always check that the tool is safe for operation. Check the security of the nylon cutting head and the guard and the switch trigger/lever for easy and proper action. Check for clean and dry handles and test the on/off function of the switch.

Check damaged parts before further use of the tool.

A guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by our authorized service center unless indicated elsewhere in this manual.

4. Switch on the motor only when hands and feet are away from the nylon cutting head.

5. Before starting make sure that the nylon cutting head has no contact with hard objects such as branches, stones etc. as the nylon cutting head will revolve when starting.

Method of operation

1. Only use the tool in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing.

2. Take care against injury to feet and hands from the nylon cutting head.

3. Never cut above waist height.

4. Never stand on a ladder and run the tool.

5. Never climb up into trees to perform cutting operation with the tool.

6. Never work on unstable surfaces.

7. Remove sand, stones, nails etc. found within the working range. Foreign particles may damage the nylon cutting head.

8. Should the nylon cutting head hit stones or other hard objects, immediately switch off the motor and inspect the nylon cutting head.

9. Before commencing cutting, the nylon cutting head must have reached full working speed.

10. During operation always hold the tool with both hands. Never hold the tool with one hand during use. Always ensure a safe footing.

11. The nylon cutting head has to be equipped with the guard. Never run the tool with damaged guards or without guards in place!

12. All protective equipment such as guards supplied with the string trimmer must be used during operation.

13. Except in case of emergency, never drop or cast the tool to the ground or this may severely damage the tool.

14. Never drag the tool on the ground when moving from place to place, the tool may become damaged if moved in this manner.

15. Always remove the battery cartridge from the tool:

− whenever leaving the tool unattended;

− before clearing a blockage;

− before checking, cleaning or working on the

tool;

− whenever the tool starts vibrating abnormally;

− whenever transporting the tool.

16. Always ensure that the ventilation openings are kept clear of debris.

Maintenance instructions

1. The condition of the nylon cutting head, protective devices must be checked before commencing work.

2. Turn off the motor and remove the battery cartridge before carrying out maintenance, replacing the nylon cutting head or nylon cord and cleaning the tool.

3. Check for loose fasteners and damaged parts such as cracks in the nylon cutting head.

4. Follow instructions for lubricating and changing accessories if applicable.

5. When not in use store the equipment in a dry location that is locked up or out of children's reach.

6. Use only the manufacturer's recommended replacement parts and accessories.

7. Inspect and maintain the tool regularly, especially before/after use. Have the tool repaired only by our authorized service center.

8. Keep handles dry, clean and free from oil and grease.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

USG001-2

WARNING:

Use of this product can create dust containing chemicals which may cause respiratory or other illnesses. Some examples of these chemicals are compounds found in pesticides, insecticides, fertilizers and herbicides. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

USD301-1

Symbols

The followings show the symbols used for tool.

･ volts

･ direct current

･ no load speed

･ revolutions or reciprocation per minute

ENC007-7

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such as nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ﾟ C (122 ﾟ F).

7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F). Let a hot battery cartridge cool down before charging it.

4. Charge the battery cartridge once in every six months if you do not use it for a long period of time.

PARTS DESCRIPTION

Battery cartridge

Indication lamp

Switch trigger

Grip

Protector

Cutting tool

012869

FUNCTIONAL DESCRIPTION

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before adjusting or checking the functions on the tool. Failure to

switch off and remove the battery cartridge may result in serious personal injury from accidental start-up.

Installing or removing battery cartridge

012859

CAUTION:

• Always switch off the tool before installing or

removing of the battery cartridge.

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

1. Red indicator

2. Button

3. Battery cartridge

hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a

personal injury. To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally

fall out of the tool, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being

inserted correctly.

Power switch action

WARNING:

• Before inserting the battery cartridge in the

tool, always check to see that the switch trigger

actuates properly and returns to the "OFF"

position when released. Do not pull the switch

trigger hard without pressing in the lock-off

button. This can cause switch breakage.

Operating a tool with a switch that does not actuate

properly can lead to loss of control and serious

personal injury.

012860

To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, press in the lock-off button and pull the switch trigger. The tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

Reversing Switch for Debris Removal

012861

This tool has a reversing switch. Reversing is used only when weeds and debris are entangled in the tool. To operate the tool normally the "A" side of the switch should be depressed. If weeds and debris are jammed in the rotating head, the tool can be reversed by depressing the "B" side of the switch. In the reverse position, the tool only operates for a short period of time and automatically shut off.

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before removing weeds or debris entangled in the tool that is not removed by the reverse mode. Failure to switch

off and remove the battery cartridge may result in serious personal injury from accidental start-up.

NOTICE:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Do not change the direction of rotation while the head is still rotating, the tool may be damaged.

Speed change

012862

Two speed ranges can be preselected with the speed change switch. Flipping the speed change switch lever to the "1" position will set the tool to the low speed range and the "2" position will set the tool to the high speed range.

Battery/motor protection system

The battery cartridge and tool are provided with protection functions that will automatically reduce or cut off power when overload situations occur that may cause

1. Speed change switch lever

1. Reversing switch

1. Lock-off button

2. Switch trigger

damage to the tool or battery cartridge. If the tool becomes overloaded but not locked up, a protector is provided to reduce the revolutions to protect the motor. In this case the two indicator lamps described in the table below do not light or blink. All other protection functions can be identified by the indicator lights described in the table below.

012967

Status

Blinking

Lighting On

-Lighting On

Battery power has been nearly used up.

Battery protector is

shutting off the power battery power has been used up.

Action to be taken

Replace the battery with fully charged

one.

Replace the battery with fully charged one.

Rest the equipment for a while.

Blinking

Overload protector is shutting off the power - the motor was locked.

Blinking Blinking

Electric or electronic

lfunction

Ask your local authorized service center for repairs.

Overheat protector is shutting off the power - overheating.

Release the switch trigger and remove the

cause of the motor lock or overload. If the cutting tool is lock

ed by entangling weeds or the like, always remove the battery cartridge before clearing it.

010823

Nylon cutting head

NOTICE:

• Do not attempt to bump feed the head while the tool

is operating at a high RPM. Bump feeding at a high RPM may cause damage to the nylon cutting head.

• The bump feed will not operate properly if the head

is not rotating.

012863

The nylon cutting head is a dual string trimmer head provided with a bump & feed mechanism. To feed the nylon cord, bump the cutting head against the ground while rotating at a low RPM. The nylon cord is

automatically cut to the proper length by the cutter on the protector.

NOTE:

• If the nylon cord does not feed out while bumping

the head, rewind/replace the nylon cord by following the procedures described under "Maintenance."

• Do not bump the tool to the concrete or asphalt

surface. Bumping to this kind of objects may cause the tool damage.

1. Most effective cutting area

1. Indicator lamps

Battery remaining capacity indicator (only for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining capacity indicator.

011715

Press the CHECK button to indicate the battery remaining capacity. The indicator lamps will light up for approximately three seconds.

Indicator lamps

Lighted Off Blinking

Remaining capacity

70% to 100% 45% to 70%

20% to 45% 0% to 20%

Charge the battery.

The battery may have malfunctioned.

011713

•

When only the lowermost indicator lamp (next to the "E") blinks, or when none of the indicator lamps light up, the battery capacity has run out, so the tool does not operate. In these cases, charge the battery or replace the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, which means that the battery has reached the end of its service life.

• When the upper two and lower two indicator lamps

light alternately, the battery may be malfunctioning. Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the

actual level during use or immediately after using the tool.

• Depending on the conditions of use and the

ambient temperature, the indication may differ slightly from the actual capacity.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out any work on the tool. Failure to switch off and

remove the battery cartridge may result in serious personal injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially assembled state may result in serious personal injury from accidental start-up.

Installing the handle

012864

Fit the grip onto the shaft pipe and tighten them with two screws. Make sure that the spacer on the shaft pipe is located between the grip assembly and the other grip. Do not remove or shrink the spacer.

NOTE:

• In some countries, the spacer is not provided with

the tool. In that case, align the handle to further side of the line which is indicated by the arrow marks.

Installing the protector (guard)

012865

WARNING:

• Never use the tool without the protector

illustrated in place. Failure to do so can cause serious personal injury.

CAUTION:

• Be careful not to contact the sharp nylon cord

cutter on the protector while installing. Contact with the cutter could result in personal injury.

1. Nylon cutting head

2. Protector

1. Grip

2. Spacer

1. Indicator lamps

2. CHECK button

012867

Set the protector so that the rib of the shaft fits into the groove of the protector. Then fix the protector and the protector cover to the clamp with two bolts as shown. Tighten the right and left bolts evenly.

Installing nylon cutting head

CAUTION:

• Only use the nylon cutting head with the

protector. Failure to do so may cause serious personal injury.

NOTICE:

• Be sure to use genuine Makita nylon cutting head.

Turn the tool upside down so that you can replace the nylon cutting head easily.

012868

Before you mount the nylon cutting head, turn the cutter holder until you can see a slit under the hole. Insert the lock key through the hole so that the base does not turn. Then screw the cutting head clockwise with holding the lock key until the cutting head is locked firmly. After the cutting head is mounted, remove the lock key. Make sure that the cutting head is tightly attached to the tool before use. To remove the nylon cutting head, turn it counterclockwise while holding the lock key.

CAUTION:

• If the nylon cutting head accidentally impacts a

rock or hard object during operation, stop the tool and inspect it for any damage. If the nylon cutting head is damaged, replace it immediately. Otherwise it may be fly apart and

cause serous personal injury.

OPERATION

CAUTION:

• Do not cut high grass at a time. Cutting high

grass at a time near the root may cause the tool motor under overloaded as grass is entangled, and may result in damage to the tool.

• Do not contact the cutting head with the

ground surface. It may cause the motor under overload, and result in damage to the tool.

• Do not force the trimmer in densely grown grass.

012891

CAUTION:

• Do not use the trimmer as if you dig out the ground

with it.

Cutting the grass near a tree, concrete block, brick or garden stone

012890

Tilt the tool with paying attention that the tool does not contact the ground surface. Approach the tip of the nylon cord to the grass. Smooth feeding out may be needed because the tip of the nylon cord touches the ground and wears more quickly than usual.

NOTE:

• Getting the trimmer too close to a tree, concrete

block, brick, garden stone or the like during the edging work or similar cutting work may cause the nylon cord to be cut off halfway inside the cutter head. In that case, turn off the tool, remove the cutting head and set the nylon cord properly again. Regarding to how to set the nylon code, refer to the section in "Maintenance".

1. Lock key

2. Cutter holder

1. Protector

2. Bolts

3. Protector cover

It is recommended to keep the tool more than 5 cm away from the tree, concrete block, brick, garden stone or the like so that the tip of the nylon code does not contact the hard obstacle and you can expect the best performance. Start the trimmer before getting close to the grass to be cut. Cut the grass using the nylon cord tip by moving the trimmer from right to left and proceed slowly, keeping the trimmer at the angle of about 30 ﾟ in relation to the ground surface. When cutting high grass, cut in layers always beginning from the top with each cut length short.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to perform inspection or maintenance on the tool. Failure to switch off and remove the battery

cartridge may result in serious personal injury from accidental start-up.

NOTICE:

Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Replacing the nylon cord

WARNING:

• Make sure that the cover of the nylon cutting

head is secured to the housing properly as described below. Failure to properly secure the

cover may cause the nylon cutting head to fly apart resulting in serious personal injury.

• Use only 2.0 - 3.0 mm (0.08" - 0.12") diameter

nylon cord. Never use metal wire, rope or the like. Use of something other than the

recommended nylon cord may cause damage to the trimmer and result in serious personal injury.

012902

Press inward on the housing latches and lift upward to remove the cover. Discard any of the remaining nylon cord.

80mm

012904

Hook the middle of the new nylon cord to the notch located at the center of the spool between the 2 channels provided for the nylon cord. One side of the cord should be about 80mm (3-1/8") longer than the other side. Wind both ends firmly around the spool in the direction marked on the head for right hand direction indicated by RH.

100mm

010774

Wind all but about 100 mm (3-15/16") of the cords, leaving the ends temporarily hooked through a notch on the side of the spool.

010775

Mount the spool in the housing so that the grooves and protrusions on the spool match up with those in the housing. Keep the side with letters on the spool visible on the top. Then, unhook the ends of the cord from their temporary position and feed the cords through the eyelets to come out of the housing.

1. Eyelets

1. Notches

1. Spool

2. For right hand rotation

1. Cover

2. Latches

3. Press

012903

Align the protrusion on the underside of the cover with the slots of the eyelets. Then push cover firmly onto the housing to secure it. Make sure the latches fully spread in the cover. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

1. Cover

2. Protrusion (Not shown)

3. Slot of the eyelet

TROUBLE SHOOTING

Before asking for repairs, first, conduct your own inspection. If you find a problem that is not explained in

the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized or Factory Service Centers, always using Makita replacement parts.

Malfunction status Cause Action

Battery cartridge is not installed.Install the battery cartridge.

Battery problem (under voltage).

Recharge the battery. If recharging is not effective, replace battery.

The drive system does not work correctly.

Ask

your local authorized service center

for repair.

Rotation is in reverse.

Change the direction of rotation with the reversing switch.

Battery's charge level is low.

Recharge the battery. If recharging is not effective, replace battery.

Overheating.

Stop using of tool to allow it to cool down.

Battery is installed improperly.

Install the battery cartridge as described in this manual.

Battery power is dropping.

Recharge the battery. If recharging is not effective, replace battery

The drive system does not work correctly.

Ask your local authorized service center for repair.

The nylon cutting cord does not feed.

The cord is used up or tangled in the spool.

Rewind the cord.

The cord cutter

on the protector

is damaged or missing.

Ask your local authorized service center for repair.

The cord extends past the protector.

Rewind the cord.

Foreign object such as branch is jammed between the guard and the nylon cutting head.

Remove the foreign object.

The drive system does not work correctly.

Ask your local authorized service center for

repair.

One nylon cord has been broken

and the head got unbalanced.

Bump the nylon cutting head against the ground while it is rotating to cause the cord to feed.

The drive system does not work correct

ly.

Ask your local authorized service center for repair.

Cutting head and motor cannot stop:

Remove the battery immediately!

Electric or electronic malfunction.

Remove the battery and ask your local

authorized service center f

or repair.

Abnormal vibration: Stop the tool immediately!

The nylon cutting cord is not cut off at the correct length.

Motor does not run.

Motor stops running after a little use.

It does not reach maximum RPM.

Cutt

ing head does not rotate: Stop the tool immediately!

012856

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or

attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

• Nylon cutting head

• Makita genuine battery and charger

• Battery converter BCV02

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.

This Warranty does not apply where:

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

repairs have been made or attempted by others: repairs are required because of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have been made to the tool.

EN0006-1

+ 30 hidden pages

Makita HRU01 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual