Makita HR4013C Owner's Manual

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Rotary Hammer

HR4003C
HR4013C
HR5202C
HR5212C

IMPORTANT: Read Before Using.

DOUBLE INSULATION

1

014873

ENGLISH (Original instructions)

SPECIFICATIONS

Model HR4003C HR4013C HR5202C HR5212C

Capacities

No load speed (min-1) 250 - 500 150 - 310

Blows per minute 1,450 - 2,900 1,100 - 2,250

Overall length 479 mm 599 mm

Net weight 6.2 kg 6.8 kg 10.9 kg 11.9 kg

Safety class /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Do not dispose of electric equipment
together with household waste
material!
In observance of the European
Directive, on Waste Electric and
Electronic Equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.

Intended use
The tool is intended for hammer drilling in brick,
concrete and stone as well as for chiselling work.

Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.

Carbide-tipped bit 40 mm 52 mm

Core bit 105 mm 160 mm

END201-7

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

ENE044-1

ENF002-2

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

2

GEA005-3

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always
recommended.

Personal safety

11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools

with your finger on the switch or energising power
tools that have the switch on invites accidents.

14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.

15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

16. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.

17. If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-

related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.

20. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

21. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

22. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many

accidents are caused by poorly maintained power
tools.

23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the

power tool for operations different from those
intended could result in a hazardous situation.

Service

25. Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the

safety of the power tool is maintained.

26. Follow instruction for lubricating and

changing accessories.

27. Keep handles dry, clean and free from oil and
grease.

GEB007-7

ROTARY HAMMER SAFETY
WARNINGS

1. Wear ear protectors. Exposure to noise can
cause hearing loss.

2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.

3

3. Hold power tool by insulated gripping

surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.

4. Wear a hard hat (safety helmet), safety

glasses and/or face shield. Ordinary eye or
sun glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
mask and thickly padded gloves.

5. Be sure the bit is secured in place before

operation.

6. Under normal operation, the tool is designed

to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.

8. Always be sure you have a firm footing.

Be sure no one is below when using the tool
in high locations.

9. Hold the tool firmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area

when operating. The bit could fly out and
injure someone seriously.

13. Do not touch the bit or parts close to the bit

immediately after operation; they may be
extremely hot and could burn your skin.

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function
on the tool.

Switch action

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and
returns to the "OFF" position when released.

Switch trigger

This switch functions when setting the tool in
and

symbol modes.

1. Switch trigger

1

014028

To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.

Switch button

This switch functions when setting the tool in
mode.

014880

When the tool is in the symbol mode, the switch
button projects out and lights in red.
To start the tool, press the switch button. The switch
light turns in green.
To stop the tool, press the switch button again.

1. Switch button

1

symbol

symbol

4