Makita HR2010 User guide
I
20
mm
(13/16”)
MODEL
INSTRUCTION MANUAL
HRZOlO
SPEC
I
FI
CAT1 0 N
Capacities
In concrete
20
mm
(13116”l (15116“)
S
In
wood
24” 13
In steel
mm
(112”)
No load speed Blows
(RPM)
0
~
900
per minute length weight
~
4’000
DOUBLE
INS
U
L
Overall
287
mm
(11-5116”) (6.8
3.1
AT
Net
I 0 N
kg
Ibs)
GENERAL SAFETY RULES
(For
All
Tools)
WARNING! Read and understand all instructions.
to
follow
all
instructions listed
below,
may
result in electric
shock, fire and/or serious personal injury.
SAVE
THESE INSTRUCTIONS
READ ALL INSTRUCTIONS.
1.
Keep your work area clean and well
accidents.
2.
Do not operate power tools
of flammable liquids, gases, or dust. Power tools create sparks which may
ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to loose control.
4.
Double Insulated tools are equipped with a polarized plug (one blade is wider
than the other.) This plug will fit in a polarized outlet only one way.
plug does
contact a qualified electrician to install a polarized outlet. Do not change
the plug
wire grounded power cord and grounded power supply system.
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
6.
Don't expose power tools to rain or wet conditions. Water entering a power
tool
7.
Do not abuse the cord. Never use the cord to carry
from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged cords increase the risk of
electric shock.
8.
When operating a power tool outside, use an outdoor extension cord marked
"W-A" or
of
electric shock.
9.
Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use tool while tired or under the influence of drugs,
alcohol, or medication.
may result in serious personal injury.
IO.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
not
fit fully in the outlet, reverse the plug.
in
any way. Double insulation H eliminates the need for the three
will
increase the risk
"W."
These cords are rated for outdoor use and reduce the risk
in
of
A
moment of inattention while operating power tools
lit.
Cluttered benches and dark areas invite
explosive atmospheres, such as
If
it
still does not fit,
electric shock.
the
tools or pull the plug
in
the presence
Failure
If
the
11.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying
tools with your finger on the switch or plugging
on invites accidents.
12. Remove adjusting keys or switches before turning the tool on.
a key that is left attached to a rotating part of the tool may result
injury.
13. Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the tool in unexpected situations.
14. Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
15. Use clamps or other practical way to secure and support the workpiece to
a stable platform. Holding the work by hand or against your body is unstable
and may lead to
16. Do not force tool. Use the correct tool for your application. The correct tool
will
do the job better and safer at the rate for which
17. Do not use tool
be controlled
18. Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the
reduce the risk of starting the tool accidentally.
19. Store idle tools out of reach of children and other untrained persons.
are dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges are less likely
to control.
21. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tools operation. If damaged, have
the
tool service before using. Many accidents are caused by poorly maintained
tools.
22. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool, may become hazardous
when used on another tool.
Tool
23.
24. When servicing a tool. use only identical replacement parts. Follow instruc-
service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of
injury.
tions in the Maintenance section of this manual. Use of unauthorized parts
or failure to follow Maintenance Instructions may create a risk of electric shock
of injury.
loss
of control.
if
switch does not turn
with
the switch is dangerous and must be repaired.
tool.
in
tools that have the switch
A
wrench or
in
personal
it
is designed.
it
on or off. Any
Such preventive safety measures
tool
that cannot
Tools
to
bind and are easier
3
SPECIFIC SAFETY RULES FOR ROTARY HAMMER
1.
Hold tools
the
"live" wire will make exposed metal parts
operator.
2.
Wear ear protectors when using the tool
exposure
by
insulated gripping surfaces when performing an operation where
cutting tool may contact hidden wiring or its own cord. Contact with
of
the tool "live" and shock the
for
extended periods. Prolonged
to
high intensity noise can cause hearing
loss.
SYMBOLS
a
The followings show the symbols used
v
A
Hz
kg
h
min
S
Q
=
%
lol
A
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
.................................
volts
amperes
herts
kliograms
hours
minutes
seconds
alternating current
direct current
no load speed
alternating or direct current
Class
II
Construction
splash-proof construction
for
tool.
A4
...
/min
@
4
.................................
................................
.................................
watertight construction
revolutions or reciprocation per minute
number of blow
Installing or removing the drill bit
CAUTION:
Always be sure that the tool is switched
off
and unplugged before installing or removing
the bit.
To install the bit, turn the chapge ring in the
of
direction
the arrow until the
the change ring
is
aligned with the I mark
fi
mark on
on the rubber cap. Align the key groove on
the bit shank with the mark on the
rubber cap and insert the bit.
~
mark mark
Turn the change ring in the direction
arrow until the
is
aligned with the mark on the rubber
fi
mark on the change ring
cap to secure the bit.
To
remove the bit, turn the change ring in the
direction
change ring
of
the arrow until the
is
aligned with the mark on the
fi
mark on the
rubber cap. Then pull out the bit.
of
the
mark
5
Loading...