Makita DDF343SYX3 User manual

	Cordless Driver Drill	Instruction manual
GB
	Perceuse-visseuse sans fil	Manuel d’instructions
F
	Akku-Bohrschrauber	Betriebsanleitung
D
	Trapano avvitatore a batteria	Istruzioni per l’uso
I
	Accuschroefboormachine	Gebruiksaanwijzing
NL
	Taladro sin cables	Manual de instrucciones
E
	Berbequim sem fios	Manual de instruções
P
	Akku bore-skruemaskine	Brugsanvisning
DK
	Δραπανοκατσάβιδο μπαταρίας	Οδηγίες χρήσης
GR

DDF343

DDF453

009075

1	4

2

3

1

012153

2

012128

		A	B
	5		6
3	009077	4	009078
	7		8

9 10

5

009079

6

009080

11

7

009081

8

009082

2

ENGLISH (Original instructions)

Explanation of general view

1.	Red indicator	5.	Switch trigger	9.	Graduation
2.	Button	6.	Reversing switch lever	10.	Pointer
3.	Battery cartridge	7.	Speed change lever	11.	Sleeve
4.	Star marking	8.	Adjusting ring

SPECIFICATIONS

	Model			DDF343		DDF453
			Steel	10 mm		13 mm
Capacities			Wood	25 mm		36 mm
		Wood screw		5.1 mm x 63 mm		6 mm x 75 mm
		Machine screw			6 mm
No load speed (min-1)			High (2)		0 - 1,300
			Low (1)		0 - 400
Overall length				192 mm		214 mm
	Net weight			1.4 kg		1.6 kg
Rated voltage				D.C. 14.4 V		D.C. 18 V

•Due to our continuing program of research and development, the specifications herein are subject to change without notice.

•Specifications and battery cartridge may differ from country to country.

•Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Intended use

ENE034-1

The tool is intended for drilling and screw driving in wood, metal and plastic.

General Power Tool Safety
Warnings	GEA010-1

WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

CORDLESS DRIVER DRILL
SAFETY WARNINGS	GEB088-1

1.Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2.Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

3.Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

4.Always be sure you have a firm footing.

Be sure no one is below when using the tool in high locations.

5.Hold the tool firmly.

6.Keep hands away from rotating parts.

7.Do not leave the tool running. Operate the tool only when hand-held.

8.Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

9.Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS ENC007-7

FOR BATTERY CARTRIDGE

1.Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2.Do not disassemble battery cartridge.

3.If operating time has become excessively shorter, stop operating immediately. It may result in a risk

3

of overheating, possible burns and even an explosion.

4.If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

5.Do not short the battery cartridge:

(1)Do not touch the terminals with any conductive material.

(2)Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.

(3)Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

6.Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).

7.Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

8.Be careful not to drop or strike battery.

9.Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1.Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2.Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

3.Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.

4.Charge the battery cartridge once in every six months if you do not use it for a long period of time.

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge (Fig. 1)

•Always switch off the tool before installing or removing of the battery cartridge.

•To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.

•To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely. Install it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

•Do not use force when installing the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Battery protection system (Lithium-ion battery with star marking) (Fig. 2)

Lithium-ion batteries with a star marking are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life.

The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions:

• Overloaded:

The tool is operated in a manner that causes it to draw an abnormally high current.

In this situation, release the trigger switch on the tool and stop the application that caused the tool to become overloaded. Then pull the trigger switch again to restart.

If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the trigger switch again.

• Low battery voltage:

The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.

Switch action (Fig. 3)

CAUTION:

•Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when

released.

To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

Reversing switch action (Fig. 4)

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation.

When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

CAUTION:

•Always check the direction of rotation before operation.

•Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.

•When not operating the tool, always set the reversing switch lever to the neutral position.

Speed change (Fig. 5)

To change the speed, first switch off the tool and then slide the speed change lever to the “2” side for high speed or, “1” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job.

CAUTION:

•Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and “2” side, the tool may be damaged.

4