Makita B05001 User guide
Random Orbit
Sander
MODEL
INSTRUCTION MANUAL
BO5001
Pad
size
123
mm
14-13/16’,)
*
Manufacturer reserves the right
Note: Specifications may differ from country to country.
Orbits
per
minutes
10,000
to
change specifications without notice.
Dimensions
127
mm x 123
(L
x
W
x
mm
x
(5” x 4-13/16“ x 6”)
154
H)
mm
Net weight
1,3
kg
(2,9
IMPORTANT
SAFETY
WARNING:
PRECAUTIONS SHOULD ALWAYS
THE RISK
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
OF
FIRE, ELECTRIC SHOCK, AND PERSONAL
INSTRUCTIONS
(For
All Tools)
BE
FOLLOWED TO REDUCE
INJURY, INCLUDING THE FOLLOWING:
READ
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
ALL INSTRUCTIONS.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
or wet locations. Keep work area well
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
or locked-up place
DON'T FORCE TOOL.
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in
moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and
rized service facility. Inspect extension cords periodically and replace
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.
-
out of reach of children.
It
will do the job better and safer at the rate for which
it
frees both hands to operate tool.
in
lit.
Don't expose power tools to rain.
use, tools should be stored
if
cutting operation is
it
to disconnect from
if
damaged, have repaired by autho-
in
dry, and high
in
damp
if
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
that
see
it
15.
AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger
on switch. Be sure switch is OFF when plugging
16.
OUTDOOR USE EXTENSION
extension cords intended for use outdoors and
17.
STAY ALERT. Watch what
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Don’t
use tool if switch does not turn
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
21.
POLARIZED PLUGS: To reduce the risk of electric shock, this equipment ha8
a polarized plug (one blade is wider than the other). This plug will fit in a
polarizedoutlet onlyone way. If the plug does not fitfully in theoutlet, reverse
the plug. If it still does not fit, contact
proper outlet.
VOLTAGE
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified for
the tool can result in
If
in
doubt,
than the name plate rating is harmful to the motor.
keys and adjusting wrenches are removed from tool before turning
on.
in.
CORDS.
you
are doing, use common sense. Don’t operate
Do
not change the plug in any way.
WARNING: Before connecting the tool to a power source (receptacle,
DO
NOT
SERIOUS
PLUG
INJURY to the user-as well as damageto the tool.
IN
THE TOOL. Using a power source with voltage less
When tool is used outdoors, use only
so
marked.
it
on and off.
a
qualified electrician to install the
it
will
ADDITIONAL SAFETY RULES
1.
Hold the tool firmly.
2.
Do
not leave the tool running. Operate the tool only when hand-held.
3.
This tool has not been waterproofed,
surface.
so
do not use water on the workpiece
SAVE THESE INSTRUCTIONS.
3
Loading...