Table
Saw
255
mm
(10")
MODEL
With Electric Brake
INSTRUCTION MANUAL
2711
SPEC
IF
I
CAT
I
0
N
S
Blade
Cutt,ng
Arbor
thole
dldnlPtel
255
mn,
iio"i
CaPdCmeF
90" 45"
91
mm
13
9
16'1
63
nirn
12
1 z 'I
123
600
Fixed
mm x 405
5
8' x 15
table
Table
inmi
15
16 I 111
size
IL
295
x
WI
Sliding
mm
58' x 19
x
table
497
mm
$)I6
No
I
load
3
800 1090
Rk"
142 7<a x 28
Manufacturer reserves the right to change specifications without notice.
*
Note. Specifications may differ from country to country.
Dimensions
IL
mm
x
x W x
715
mm
im"
i:z'
mm
I
Ne,
wetghf
32
5
kg
171 6 ibsi
HI
x
470
ia
For Your Own Safety Read Instruction
Manual Before Operating Table Saw
GENERAL SAFETY PRECAUTIONS
(For
All
Tools)
1
KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the
tools applications and limitations, as well as the specific potential hazards
peculiar to
2.
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
3.
see that keys and adjusting wrenches are removed from tool before turning
it
on.
4.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DON'T USE IN DANGEROUS ENVIRONMENT. Don't use power tools in damp
5.
or wet locations, or expose them to rain. Keep work area well lighted.
KEEP CHILDREN AWAY. All visitors should be kept safe distance from work
6.
area.
MAKE WORKSHOP KID PROOF with padlocks, master switches, or by
7.
removing starter keys.
DON'T FORCE TOOL.
8.
it
was designed.
USE RIGHT TOOL. Don't force tool or attachment to do a job for which
9.
was not designed.
WEAR PROPER APPAREL. Wear no loose clothing, gloves, neckties, rings.
10.
bracelets, or other jewelry which may get caught in moving parts. Nonslip
footwear is recommended. Wear protective hair covering to contain long hair.
11.
ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they
are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It's safer
than using your hand and
13.
DON'T OVERREACH. Keep proper footing and balance at all times.
14.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories such as
blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is
in off position before plugging in.
it.
It
will do the job better and safer at the rate for which
it
frees both hands to operate tool.
it
2
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for
recommended accessories. The use of improper accessories may cause risk
of injury to persons.
18.
NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or
if the cutting tool is accidentally contacted.
19.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
it
part that is damaged should be carefully checked to determine that
-
operate properly and perform its intended function
of
of moving parts, binding
any other conditions that may affect its operation.
is damaged should be properly repaired or replaced.
20.
DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of
rotation of the blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t
it
leave tool until
22. PROPER GROUNDING. This tool should be grounded while in use to protect
the operator from electric shock.
23.
EXTENSION CORDS: Use only three-wire extension cords which have threeprong grounding-type plugs and three-pole receptacles which accept the
tool’s plug. Replace or repair damaged or worn cord immediately.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
If
the tool.
voltage less than the nameplate rating is harmful to the motor.
in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
comes to a complete stop.
moving parts, breakage of parts, mounting, and
check for alignment
A
guard or other part that
-
as well as damage to
will
3
G
R
0
U N D I N G INSTRUCT IONS
ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or
breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided-if
let installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. The conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is necessary, do not connect
the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or serviceman if the grounding instructions are
not completely understood, or if in doubt as to whether the tool is properly
grounded.
This tool is intended for use on a circuit that has an outlet that looks like the
one illustrated in Figure
illustrated in Figure A. A temporary adapter, which looks like the adapter illus-
trated in Figure
as shown in Figure
adapter should be used only until a properly grounded outlet can be installed by
a qualified electrician. The green-colored rigid ear, lug, etc. extending from the
adapter must be connected to a permanent ground such as a properly grounded
outlet box.
B
A.
The tool has a grounding plug that looks like the plug
and C, may be used to connect this plug to a 2-pole receptacle
B
if a properly grounded outlet is not available. The temporary
it
will not fit the outlet, have the proper out-
4
FIG. A
Q
Grounding Pin
I
GROUNDING METHODS
FIG.
B
Cover
of
Outlet
Grounded
Box
-
FIG. C
Adaoter
9'
Grounding
Means
ADDITIONAL SAFETY RULES
1.
Wear eye protection.
2.
Don't use the tool
3.
Never use the tool with an abrasive cut-off wheel installed.
4.
Check the blade carefully for cracks or damage before operation. Replace
cracked or damaged blade immediately.
5.
Clean the spindle, flanges (especially the installing surface) and hex
before installing the blade. Poor installation may cause vibration/wobbling
or slippage of the blade.
6.
Use saw-blade guard and spreader for every operation for which
used, including all through sawing operations. Through sawing operations
in
are those
ripping or cross cutting. Never use the tool with a faulty blade guard or
secure the blade guard with a rope, string, etc. Any irregular operation of
the blade guard should be corrected immediately.
7.
Avoid cutting nails, screws, etc. Inspect for and remove all nails, screws and
other foreign matter from the workpiece before operation.
8.
Remove wrenches, cut-off pieces, etc. from the table before the switch is
turned on.
9.
Never wear gloves during operation.
IO.
Keep hands out of the line of saw blade.
to stand
11.
Make sure the blade is not contacting the spreader or workpiece before the
switch is turned on.
12.
Before cutting an actual workpiece, let the tool run for a while. Watch for
vibration or wobbling that could indicate poor installation or a poorly balanced
blade.
13.
Use a push stick when required. Push sticks should be used for ripping
narrow workpieces to keep your hands and fingers well away from the blade.
14.
Pay particular attention to instructions for reducing risk of KICKBACK.
KICKBACK is the ejection of the workpiece from the tool back towards the
operator. Avoid KICKBACKS by keeping the blade sharp, by keeping the rip
fence parallel to the blade, by keeping the spreader, antikickback fingers and
blade guard
until
you have pushed
piece that is twisted or warped or does not have a straight edge to guide
along the fence.
15.
Do not perform any operation freehand. Freehand means using your hands
to support or guide the workpiece.
16.
Never reach around or over saw blade.
17.
Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard
workpieces. Do not bend or twist workpiece while feeding. If you stall or
which the blade cuts completely through the workpiece as in
in
line with the path of the saw blade.
in
in
presence of flammable liquids or gases.
Do
not stand or permit anyone else
place and operating properly, by not releasing the workpiece
it
all the way past the blade, and by not ripping a work-
it
can be
nut
5
jam the blade
tool. Then clear the jam.
18.
Never remove cut-off pieces near the blade or touch the blade guard while
the blade is running.
19.
Don't abuse cord. Never yank cord to disconnect from receptacle. Keep cord
away from heat,
in
the workpiece, turn the tool off immediately. Unplug the
oil,
water and sharp edges.
SAVE THESE INSTRUCTIONS.
6
Movement and transport
of
table saw
Before moving the table saw, tighten the
wing bolt to secure the sliding table.
When moving the table saw, hold
it
by the
fixed table and the bars.
Be sure to use two persons to lift and move
it.
When transporting the table saw by
vehicle, secure
it
with a rope or other sub-
stantial means.
ASSEMBLY
The table saw
is
shipped from the factory with the ruler guides, miter gauge, saw blade,
rip fence, blade guard and table insert not installed. Assemble
CAUTION
Always be sure that the tool
:
is
switched off and unplugged before assembly.
Installing ruler guides
Install the graduated ruler guide on the
front side of the fixed table and the non-
graduated
one
on the
rear
side.
Use
the hex
wrench to tighten the bolts.
as
follows.
Sliding fable
Fixed
fable
7
Installing miter gauge
Insert the wooden gauge into the miter
gauge and tighten
the
two
screws lightly
but firmly. The wooden gauge will be used
later to help you accurately make crosscuts.
Place the miter gauge on the sliding table
with the wooden gauge extending toward
the fixed table. Insert the longer miter
gauge installation screw through the hole
(A)
in the miter gauge and screw
it
into the
threaded hole in the sliding table. Insert
the shorter miter gauge installation screw
through the hole
(B)
and screw
it
into the
nut in the sliding table. Loosen the wing
bolt securing the sliding table before
mov-
ing the sliding table.
Installing or removing
saw
blade
Hold the outer flange with the offset
wrench and loosen the hex nut clockwise
with the wrench (the hex nut has left hand
thread). Then remove the outer flange and
flange.
8
Install the blade between the two flanges.
Then install
the
outer flange and hex nut
onto the arbor, making sure the teeth of
the blade are pointing down
of
the table.
at
the front
To secure the blade in place, hold the outer
flange with the offset wrench, then tighten
the hex nut counterclockwise with the
wrench. When tightening the hex nut, the
offset wrench handle should be supported
as
by the table
SURE
TO TIGHTEN THE HEX NUT
shown in the figure. BE
SECURELY.
CAUTION
Be sure to hold the hex nut carefully with the wrench.
:
If
your grip should slip, the
wrench may come off the hex nut, and your hand could strike the sharp blade edges.
9
Installing and adjusting rip fence
Loosen the lever on the rip fence and fit
the rip fence on the ruler guides.
Lever
Rip
Ruler
fence
guide
1
I
To check to be sure that the rip fence
parallel with the blade, secure the rip fence
2
-
3
mm
(5/64"
-
1/8")
from the blade.
Raise
the blade up to maximum elevation.
a
(B)
crayon.
between
Mark one of the blade teeth with
Measure the distance (A) and
the rip fence and blade. Take both measure-
ments using the tooth marked with the
two
crayon. These
be identical. If the rip fence
with the blade, proceed
Insert
a
screwdriver into the hole in the
measurements should
is
not parallel
as
follows:
rear end of the rip fence, then loosen
the screw counterclockwise two or three
turns.
two
Loosen the
bolts on the top of the
rip fence with the wrench.
it
Adjust the rip fence until
parallel with the blade, then secure
becomes
it
by
tightening the bolts.
Tighten the screw in the hole in the rear
two
end of the rip fence clockwise
or
three turns.
is
10
Tighen the lever on the rip fence. If the rip
fence
is
not
secure enough,
in the tightened position and tighen the
screw in the hole in the rear end
fence clockwise. However, do not tighten
the screw excessively, or the lever will become loose.
leave
the
of
the rip
lever
I
CAUTION
Be sure to adjust the rip fence parallel with the blade, or a dangerous kickback condition
may occur.
Move the rip fence
blade and secure
the distance
blade. Make sure that the pointer on the
ruler guide points to the correct graduation.
If
the pointer does not point to the correct
graduation, loosen the screw on the pointer.
Then align the pointer with the correct
graduation and tighten the screw.
:
a
bit away from the
it.
Use a ruler to measure
(A)
between the rip fence and
Blade
11
Installing blade guard
CAUTION
Before installing the blade guard, adjust the depth
(Note: The depth of cut
shipped from the factory.)
Temporarily tighten the bolts with the
offset wrench. Check to be sure that the
blade and spreader are in
If they are not properly aligned, shift the
adjusting washers from one side to another
until the spreader
the blade.
:
is
adjusted to
a
straight line.
is
aligned directly behind
its
maximum elevation when the table saw
washer
Pressure plate
of
cut to
its
maximum elevation.
r--l
K'
/
Bolt
These two clearances
should be equal.
Spreader Blade
h
is
CAUTION
If the blade and spreader are not aligned properly, a dangerous pinching condition may
result during operation. Make sure they are properly aligned.
There must be
5 mm (5/32"-13/64") between the spreader
and the blade teeth. Adjust the spreader
accordingly and tighten the bolts securely.
Attach the table insert on the table, then
check to
smooth.
CAUTION
Be sure to tighten the screws securely after installing the table insert.
12
:
a
clearance of about
see
that the blade guard works
:
4
-
1
I
Soreader
-,
----
1
I
Positioning
Locate the table
table
saw
saw
in
a
well
lit
and
level
area where you can maintain good footing
It
and balance.
area that
handle the
saw
table
should be installed in an
leaves
enough room to easily
size
of your workpieces. The
should be secured with four
screws or bolts to the work bench or table
saw stand (optional accessory) using the
holes provided in
bottom
of
the
table
the
saw. When securing the table saw on the
is
work bench, make sure that there
an
opening in the top of the work bench the
size
as
same
the table saw
the opening in the bottom
so
the sawdust can drop
of
through.
No.
10
wood
40
If during operation there
screw
mm
Il-l/Z’’l
min.
length
is
any tendency for the table saw to tip over, slide
work bench or table saw stand should be secured
to
the floor.
or
move, the
13
Hand tool storage pocket
The table saw comes with a hand tool
storage pocket in the base. Keep wrenches,
screwdriver, etc. in this pocket.
Adjusting depth
The depth
of
cut
of
cut may be adjusted by turn-
ing the knob. Turn the knob clockwise
or
to raise the blade
it.
lower
The depth
the scale by the pointer
If
the knob does not turn easily, loosen the
two adjusting screws on the inside
table saw counterclockwise.
counterclockwise to
of
cut
is
indicated on
(A).
of
If
the knob
the
loose enough to be turned by vibration,
tighten the adjusting screws clockwise.
is
I
1
14
Bevel
cutting
Loosen the lock lever clockwise, then
the blade by swinging the knob until
reaches the desired angle
is
The bevel
the pointer
angle, tighten the lock lever counterclock-
wise to secure the adjustment.
indicated on the
(B).
After obtaining the desired
(0
to
45
tilt
degrees).
scale
by
it
CAUTION
After adjusting the
Adjusting
Secure the lock lever
the lock lever contacts the stopper plate.
Make sure the blade
degrees to the table surface. If the bevel
is
not
as
follows:
:I,
Use the hex wrench to loosen the bolt
securing the stopper plate.
Z
Loosen the lock lever and adjust the
blade to
secure the lock lever.
3
Slide the stopper plate until
the lock lever, then tighten the bolt
securely.
@
Make sure the pointer
the blade
tio!, loosen the screws holding the pointer
45 graduation. Then tighten screws. (Note: The screws holding the pointer
located inside the base.)
:
bevel,
be sure to tighten the lock lever securely.
stopper plate
at
the position where
is
at
90
at
90
degrees or 45 degrees, proceed
90
degrees or 45 degrees, then
(B)
is
at
90
degrees or 45 degrees.
degrees or 45
it
contacts
points to the
0"
or 45" graduation on the bevel scale when
If
it
does not point to the
(B)
and align the pointer
0"
(B)
or 45" graduawith the
0"
(B)
or
are
1s
Adjusting miter angle
Loosen the miter gauge installation screws
and adjust the miter gauge to the desired
angle
(0
to
45
degrees). Then tighten the
miter gauge installation screws securely.
CAUTION
:
After adjusting the miter angle, be sure to
securely.
Switch action
To start the tool, press the "ON" button
is
while the key
pressed in. Press the"0FF"
button to stop.
When operating the key and switch buttons,
it
is
convenient to view them through the
window area in the fixed table.
tighten the miter gauge installation screws
CAUTION
:
When not using the tool, remove the key and store
unauthorized operation.
16
it
in a secure place. This prevents
Operation
CAUTION
:
*Make sure the blade guard works smoothly and properly for making both square cuts
and bevel cuts before operation.
*Never withdraw the workpiece while the blade
a
workpiece before completing
piece firmly.
workpiece. Failure to do
Wait
until the blade has come to a complete stop before withdrawing the
so
cut, first switch the tool off while holding the work-
may cause dangerous kickback.
is
running. If you must withdraw the
Never remove cut-off pieces that may be trapped inside the blade guard while the blade
is
running.
When moving the sliding table, do not place your fingers or hands on the reverse side of
get
the sliding table. You may
your fingers pinched between the sliding table and bars.
Work helpers
Push sticks, push blocks or auxiliary fence are types of "work helpers." Use them to
make safe, sure cuts without the need for the operator to contact the blade with any part
of the body.
Push
stick
a
A push stick can be easily made from
piece of plywood 19 mm
(3/4")
to 25 mm (1")
thick.
130
mm
15")
(HI
9
5
mm
19
(314"I
mm
40
(1-1
mm
12"l
380
mm
(15"l
3/8"1
Cut out the hatched area on the stick and smooth edges with a file.
less
than 12.7 mm (1/2")
be
so
as
to be thinner than the workpiece.
(H)
dimension should
'1
mm
17
Push block
a
19
Use
mm (3/4") piece of plywood.
120 .;.4-)fm11
mm
(5")
Faceledge
parallel
6
mm
(1/4"l
5o
(2")
mm
Handle should be in center of plywood piece. Fasten with glue and wood screws
9.5
Small piece
mm x 8 mm x
50
mm
(3/8"
x
5/16" x 2")
of wood must always be glued
(5")
as
shown.
to plywood to keep the blade from dulling if the operator cuts into push block by mistake. (Never use nails in push block.)
Auxiliary fence
Make auxiliary fence from
and
19
mm
(3/4")
plywood pieces.
Wood
facing (Rip fence)
A
wood facing should be used for opera-
9.5
mm (3/8")
9.5
mm
Faceledge
parallel
Fasten
(18")
with
19
glue and
mm
(314'')
wood
(5-1
screws.
40
(1 -1
12")
mm
12"
I
tions when the blade comes close to the
rip fence. Wood facing for the rip fence
should be same
Make sure the bottom of facing
size
as
the rip fence.
is
flush
with the table surface.
18
Crosscutting
CAUTION
When making a crosscut, remove the rip fence from the table.
When cutting long or large workpieces, always provide adequate support
the table. The support should be
(1;
Loosen the wing bolt securing the sliding table.
0)
Adjust the blade to
table surface. Adjust the miter gauge to
0
the sliding table forward to cut the
wooden gauge.
Align
with the end
131
Adjust the depth
than the thickness
Firmly hold the workpiece flush against
the miter gauge and move the sliding
table forward gently to cut the workpiece.
:
at
the same height
90
degrees to the
degree. Switch the tool on and move
the cutting line on the workpiece
of
the wooden gauge.
of
cut a bit higher
of
the workpiece.
as
the table.
to
the sides of
cutting
Miter
Adjust the miter gauge to the desired angle
(0
to
45
degrees) and tighten the miter
gauge
installation
the same procedure as’mentioned in
crosscutting.
screws securely. Follow
@
for
19
The wooden gauge cannot be used for miter cutting.
NOTE:
Miter cutting capacity
is
less
than crosscutting capacity. Make sure
of
the max miter cutting capacity before operation.
The following reference table indicates some examples of miter cutting capacity.
Miter angle
O0
45"
Bevel angle
0"
45
0"
45O
0"
45"
nl4
I
Thickness
*
(2-1
*
(2-1/8")
*
(23/32")
*
(3-9/
19
(3/4")
63"
19
(3/4")
55mm
18mm
91"
19
(3/4")
Cutting capacity
I
Width
290
(1 1 -3/8")
mm
/2")
mm
1
6"
mm
260
(1
0-1 /4")
210
(8-1 /4")
255
(10")
220 mm
(8-5/8")
270
(1
0-5/8")
70
)
(2-3/4")
60
(2-3/8")
mm
mm
mm
mm
mm
mm
mm
max. thickness at each angles.
(The illustrations in the reference table show the table saw in use with the blade guard
is
removed. This
not be construed
done only in the interest of the clarity of the illustrations and should
as
a
normal working procedure.)
20
When a spacer block can be placed between
the miter gauge and workpiece, you can
a
obtain
Ripping
CAUTION
.When cutting long or large workpieces, always provide adequate support behind the
Before operating the table saw, check to be sure that the antikickback fingers operate
properly. Turn the tool off and unplug
along both sides of the blade to simulate cutting. Try to withdraw the workpiece on each
side by pulling
prevent
sharp
maintain the original shape of the fingers.
greater miter cutting capacity.
When ripping, remove the miter gauge from the sliding table.
table. The support should be
it
toward you. The antikickback fingers should grab the workpiece and
it
from moving back toward the operator. Always keep the antikickback fingers
so
they will operate properly. Keep them sharp by using round -shaped file to
at
the same height
it.
as
the table.
Feed the workpiece under the blade guard and
@
Adjust the depth of cut a bit higher than the thickness of the workpiece.
@
Tighten the wing bolt to secure the sliding table.
@)
Position the rip fence to the desired
width of rip and lock in place by tighten-
ing the lever. Before ripping, make sure
the rear end of the rip fence
If
it
is
firmly.
follow the procedure in "Adjusting rip
fence".
a
Turn the tool on and gently feed the
workpiece into the blade along with the
rip fence.
(P.11)
not secured enough,
is
secured
21
i) When the width of rip
is
150
and wider, carefully use your right
hand to feed the workpiece. Use your
left hand to hold the workpiece in
position against the rip fence.
ii)
When the width
150
mm
(2-1/2"
of
rip
-
6")
is
65
wide, use the
push stick to feed the workpiece.
mm
mm
(6")
-
iii)
When the width of rip
mm
65
(2-1/2"),
is
narrower than
the push stick cannot
be used because the push stick will
strike the balde guard. Use the auxiliary fence and push block. Attach the
auxiliary fence to the rip fence with
two
"C"
clamps.
22
I
Feed the workpiece by hand until the
end
is
about
25
mm
(I”)
from
the
front edge
Continue to feed using the push block
on
the cut
the top
is
of
the table.
of
the auxiliary fence until
complete.
23
MA1 NT ENANCE
CAUTION
Always be sure that the tool
inspection or maintenance.
Cleaning
Clean out sawdust and chips from time to time.
Carefully clean the balde guard and moving parts inside the table saw.
Lubrication
To
oil or grease the moving parts and rotating parts from time to time.
:
is
switched off and unplugged before attempting to perform
keep the table saw in tip-top running condition, and to assure maximum service life,
Use machine oil
the slide table and the bars.
Use grease or machine
moving parts under the table.
Replacing carbon brushes
Remove and check the carbon brushes
regularly. Replace when they wear down to
the timit mark. Keep the carbon brushes
clean and free to slip in the holders. Both
carbon brushes should be replaced
same time. Use only identical carbon
brushes.
Use
a
screwdriver to remove the brush
holder caps. To replace the carbon brush
in the side near the table, lower the blade
as
far
as
Loosen the lock lever,
secure
brush holder cap while viewing
the opening in the base.
the new ones and secure the brush holder
caps.
it
Remove the worn carbon brushes, insert
#I20
to wet the felt on
oil
possible
at
by
turning the knob.
tilt
45
degrees. Then loosen the
#I20
for the
at
the
the blade and
it
through
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized or Factory Service Centers,
always using Makita replacement parts.
24
ACCESSORIES
CAUTION
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories
of injury to persons. The accessories or attachments should be used only in the proper
and intended manner
:
or
attachments might present a risk
Dado head set
A
dado
into the workpiece. The dado head
sists
of two outside cutters, five inside
(Part
No
191
794-9)
is
cutting a rabbet or a wide groove
set
con-
cutters and three rings.
Outside cutters
Inside cutters
Inside cutter
Rings
Paper washers
:
6" diameter,
:
6" diameter,
:
6" diameter, 1/16" thick,
:
1/8"
1/8"
thick,
thick,
5/8"
arbor hole, 2 pcs.
5/8"
arbor hole,
5/8"
arbor hole, 1 pc.
518"
arbor hole, 3 pcs.
5/8"
arbor hole, 6 pcs.
4
pcs.
Various combinations of these cutters are used to cut grooves from
use in making joints, tenoning, grooving,
To install the dado head
(1:
Turn the tool off and unplug
(2;
Remove the blade guard with the spreader.
3,
Install the dado head
set,
proceed
it
set
with the teeth pointing down
etc.
as
follows:
before installing.
at
the front of the table
1/8"
to 13/16" for
25
@
Use the chart below to select the proper cutters to obtain the various cutting widths.
Flange Ring
I
I
114"
I I
5116"
7/16"
112"
9/16"
518"
11116"
314"
1311 6"
CAUTION
For a 1/8"
as
the saw blade.
The outer flange must be used for each cut width.
The hex nut alone must not be used to secure the dado on to the spindle.
0
0
:
cut width, the outside cutter
I
-*
10x2
I
I
-I
Outslde
cutter
I
I
I
+
is
,',~~~e
cutter
t-
ox3
o
0
0
10x4
assembled to the spindle in the same manner
0 0 0
:
NOTE
When widths slightly greater than the above are required, fit the paper washers in between
the inside and outside cutters to adjust the width.
@
Arrange the cutters
the inside cutters are positioned
gullets
of
the outside cutter.
When more than one inside cutter
used, space the tips
equidistantly in relation to one another.
Poorly spaced cutters may cause vibration and noise.
26
so
that the tips
of
the inside cutters
at
of
the
is
When installing two outside cutters
without any inside cutter, be sure that
the cutter tips do not face each other.
0
@
While tightening the hex nut, be careful to maintain the even spacing between the tips
of the inside cutters.
@
When cutting
table saw. When cutting 9/16" or wider, use optional accessory table insert (Part
343396-9).
@
Rotate the dado head one turn by hand to make sure that
before operation.
When dadoing, use featherboards. The
diagram shown illustrates dimensions for
making
made from
free of knots or craks.
a
typical featherbord.
1/2"
or narrower grooves, use the table insert originally installed on the
Be
sure to install proper table insert.
It
should be
a
straight piece of wood that
is
it
does not contact anything
X
Kerf
should
No.
be
27
Featherbords are used to keep the workpiece in contact with the rip fence and
as
table
To
@
@
@
@
When using the miter gauge during dodoing,
featherboards should not be employed.
Place
gauge and workpiece
can be pushed completely past the cutter.
When the miter agnle
spacer block should be about
shown, and to stop kickbacks.
install featherbords. proceed
Turn the tool off and unplug it.
Add 8" high flat facing board to the rip
fence, the full length of the rip fence.
Mount featherboards to the rip fence
and table
edges of featherboard will support the
workpiece until the cut
the workpiece has been pushed completely past the cutter with
Make sure featherboards are securely attached.
as
shown,
a
spacer block between the miter
so
so
that the workpiece
as
follows
that the leading
is
complete, and
is
0
degree, the
3"
wide.
:
a
push stick.
CAUTION
*Only the Makita dodo head
saw Model
*After dadoing, always replace the blade guard with the spreader back in
tion on the table saw. Refer to alignment instructions on page
Never attempt bevel cuts when dadoing.
Never dado if there
Never attempt dados in other than wood.
*When using
the depth adjustment section.) To know the depth of cut, you must measure
ruler.
28
:
271
a
1.
is
vibration (flutter) or a strange noise.
dado head
set
(Part No. 191794-9) should be used with Makita table
12.
set,
the depth of cut
is
not indicated by the pointer (A). (See
its
original posi-
it
with
a
Ring
(Part
No.
257137-6)
When cutting groove
7/16",
1/2",
9/16"
or rings.
or
1/4",
5/8",
5/16",
3/8",
use this ring
Table insert
When cutting grooves
this table insert instead
(Part
No.
343396-9)
9/16"
of
or wider, use
the standard
table insert.
Table saw stand
(Part
No.
STEX
122251
1
Place the stays on a level location and
assemble the legs inside. Secure with the
bolts and nuts, then attach the rubber caps
to the ends
Now
of
the legs.
set
the table saw on top
of
the
as-
sembled stand and secure with four bolts,
washers and nuts.
29
Saw
blades
0
Chisel tooth combination saw blade
For
rip and cross-cut work.
Most frequently used for
general carpentry.
Hole
Part
No.
0
Carbide-tipped saw blade
Fastest, smoothest longer sawing
without blade sharpening cuts
wood, drywall, plastic,
hardwood, etc.
0
Rip fence
Part
No
122328-7
0
!Screwdriver
Part
No.
2
783002-8
255-7A I 255
255-11F I 255 (10") I 5/8"
Ruller guide
Part
No.
331308-4
0
Ruller guide
No.
No.
331293-1
41 1447-7
Part
0
Switch button
Part
F
R
(10")
I
518''
I
36 1 792317-2
Hole
I
I
0
Hex wrench
No.
Part
0
Wrench 19
Part
No.
I
I
22 1792424-1
5
783203-8
781010-3
I
Part
No.
0
Offset wrench 13-22
Part
No.
782015-6
30
Hex socket head bolt
(For ruller guide)
No.
Part
922337-4
Holder
set
(Part
No.
191773-7)
Convenient to attach for better support
long workpieces.
Attach the holder to the reverse side
of
of
the
I
I
CAUTION
Never attempt to lift or move the table saw while holding the holders. When moving the
table saw, hold
Hood
When you wish to maintan clean operations through easy dust collection, connect
the vacuum cleaner (Makita Model
the table saw using this hood.
set
:
it
by the fixed table and the bars.
(Part
No.
191793-1
)
410)
to
31
255
mm
TABLE
Model
(IO")
SAW
2711
Jan
22
'87
US
32
Note.
The switch and other part configurations
may differ from country to country
33
MODEL 2711
$FD
MACHINE
~
2
3
4
5
6
7
8
9
IO
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
~
Note
The SWttch
DESCRIPTION
2
Hex
1
Rubber
2
Brush
2
Carbon Brush
4
Pan
1
PO"
1
Motor
1
Flat
1
Ball
1
Dust
1
FIELD
1
Baffle
2
Pan
1
Terminal
1
ARMATURE ASSEMBLY
IWiih
1
Fan
1
Dust
1
Ball
1
Rubber
1
Pan
1
Gear
1
Cord
1
Pan
1
Strain
1
Blade
7
Adjusting
1
Pressure
2
Hex
1
Woodruff
4
Pan
Hex Bolt
4
1
Retaining
1
Needle
1
Tension
2
Pan
1
Retainer
1
Compresston Spring
1
Reta,"e.
1
Nylon
1
Feed
1
Hex
1
Flat
1
Link
1
Flat
1
Hex
1
Set Screw
1
Lock Lever
1
Knob 45
1
Spring
2
Pan
1
Screw
1
Screw
2
Pan
1
PO,"fe,
1
Flat
1
Spring
1
Hex
1
Flat
1
Sleeve
1
Spring
1
Chip
2
Pan
1
Frame
-
and
Bolt
M5r65
Pin
Holder
Head
Housing
Washer
Bearing
Seal
ASSEMBLY
Plate
Head
Box
Item
97
Seal
Bearing
Pin
Head
Housing
Head
Relief
Guard
Plate
Bolt
Head
Bearing
Spring
Head
Pin
Nu1
Bolt
Washer
Washer
Bolt
Pin
Head
Guide
Bar
Head
Washer
Washer
Nut M10
Washer
9
Pm
Guide
Head
other
4
Cap
Screw
18
620oC8
10
Screw
9 10
15
6202LLB
6
Screw
Screw
Washer
Mar25
Key 4
Screw
M6r16
Ring
S-
Screw
10
M10
12
10
M10xIB
M5x6
5
16
Screw
M12
Screw
9
9
5-
16
Screw
pail
[With Washer]
M5x40
[With Washerl
M4x10
[With Warherl
&
15
181
M4x8
[With Washerl
M4x14
IWlth Washer)
[With Washeri
M5r30
lWilh Washeri
lWith Warherl
17
121 5
14
M5x30
[With Washer)
24
M4x10
[With Washer)
M5x8
IWgth Washer1
IO
M5x8
IWGth Washerl
specificatmns
may
difler
trom
country
65
66
67
68
69
70
71
72
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
100
101
102
103
104
105
106
107
108
109
I10
111
112
113
114
115
116
117
I18
119
120
121
122
123
124
125
126
127
90
-
to
90
91
92
93
94
95
96
97
98
99
1
country
sD
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
2
1
4
4
4
4
4
2
1
2
2
1
2
4
4
2
1
1
2
2
1
1
2
2
1
2
2
1
1
1
2
4
1
4
5
2
1
2
1
2
2
2
1
2
__
DESCRIPTION
Inner
Race
810
=,n
8
ielical
Gear
49
Waining Ring
3811
3earing
Spindle
Duter
Hex
Screw
Screw
'Aler
Utter
lex
Countersunk Head
Pan
Wooden Gauge
Table
Pan
Flxed
Hex
Flaf
Hex
Hex Socket
Flat
Holder
Sliding
Felf
Slide
Slide
Set
Pan
Felt
Slide
Slide
Slide
Pan
Cushion
Compression Spring
Wing
Set
Pan
Switch
Cord Guard
Pan
Strain
Cord
Cord
Pan
Cap
Base
Hex
Pan
Stopper
Front
Pan
Name
Pan
Flat
Hex
Lock
Flange
nouslng
Bearing
6204LLB
Retainer
Flange
Nu1
M12 19
MI0
M10
Gauge
Gauge
Nut
M10
Head
Screw
Insert
Head
Screw
Table
Socket
Washer
Socket
Washer
Bar
Table
Guide
R
Bar
Plate
Head
Screw
Guide
L
Bar
Stopper
Head
Screw
Bolt
M5x25
Plate
Head
Screw
Head
Screw
Relief
Guard
Head
Screw
20
Nut
M6
Head
Screw
Plate
Plate
Head Screw
Plate
Head
Screw
Washer
Socket
Off
Switch
50
S
COW
30
Guide
Plate
Head
8
Head
Head
6
6
Head
20
31
48
Screw
M5x12
M6x16
Bolt M6x16
Bolt
Max40
Boll
M6x35
M5x25
M6x16
I
M5x16
M4x25
M3x35
M6x25
M6x16
M6x22
Boll
M6xlO
Button
Jan
M5116
lWilh Washerl
lWith Washerl
IWith Washer]
lWith Washer]
IWith Washer1
lWith Washer]
lWith Wdsherl
22 87
US
34
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to
be free of defects from workmanship and materials for the period of ONE YEAR from the date of
original purchase. Should any trouble develop during this one-year period, return the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
the trouble is caused by defective workmanship or material, Makita
replace) without charge.
This Warranty does not apply where:
8
repairs have been made
8
repairs are required because of
8
The tool has been abused, misused or improperly maintained;
8
alterations have been made to the
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,”
AFTER THE ONE-YEAR TERM OF THIS WARRANTY.
Tlu,
Warranty g~ves you spe~ific legal nghts. dnd you may also have other nghts WhiLh vdry
\talc
10
state. Some states do not allow the exclusion
damages,
so
limitation
the above limitation or exclusion may
on
how long an implied warranty lasts,
or
attempted by others:
normal
wear and tear
tool.
OF
THIS WARRANTY.
or
limitdtion
not
apply to you. Some states do not allow
so
the above limitation may not apply
If
will
01
inspection shows
repair (or at our option,
incidental or consequentidl
to
you.
from
Makita Corporation
3-11
-8,
Sumiyoshi-cho,
Anjo, Aichi
446
88357
Japan
1
BOW
PRINTED IN JAPAN
1993-4-N
Loading...