Makita 9627 User Manual
Disc
Grinder
180
mm
(7")
MODEL
INSTRUCTION MANUAL
9627
No
load speed
(RPM)
6,000
DOUBLE
I
N
S U LATlO
Overall length Net weight Spindle thread
442
mm
I1
7-1
/2"l
5.4
kg
I1
1.9
Ibs)
518-1
N
1 UNC
IMPORTANT
SAFETY
WARNING:
WHEN
INSTRUCTIONS
(For
USING
All
Tools)
ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE
RISK
OF
FIRE, ELECTRIC SHOCK, AND PER-
SONAL INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
or wet locations. Keep work area well
Don't use tool
3.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
4.
STORE IDLE TOOLS. When not
or locked-up place - out of reach of children.
DON'T FORCE TOOL.
5.
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
6.
heavy-duty tool. Don't use tool for purpose not intended.
7.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
8.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
dusty.
9.
DON'T ABUSE CORD. Never carry tool by cord or yank
receptacle. Keep cord from heat, oil, and sharp edges.
IO.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
11.
DON'T OVERREACH. Keep proper footing and balance at all times.
12.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil and grease.
13.
DISCONNECT TOOLS. When not
ing accessories, such as blades, bits, cutters.
in
presence of flammable liquids or gases.
in
It
will
do the job better and safer at the rate for which
it
frees both hands to operate tool.
lit.
Don't expose power tools to rain.
use, tools should be stored
in
use, before servicing, and when chang-
in
it
to disconnect from
in
damp
dry, and high
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger
on switch. Be sure switch is
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
17.
STAY ALERT. Watch what you are doing, use common sense. Don’t operate
OFF
when plugging
in.
so
marked.
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.
Have defective switches replaced by authorized service center. Don’t use
if
tool
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
switch does not turn
it
on and off.
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.1 be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result
SERIOUS INJURY to the user - as well
as
damage to
in
the tool, If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
voltage less than the nameplate rating is harmful to the motor.
3
ADDITIONAL SAFETY RULES
1.
Keep guards
2.
Use only wheels having a maximum operating speed at least as high as
Load
RPM"
wheels, be sure to use only fiberglass-reinforced wheels.
3.
Check the wheel carefully for cracks or damage before operation. Replace
cracked or damaged wheel immediately.
4.
Use only flanges specified for this tool.
5.
Be careful not to damage the spindle, the flange (especially the installing
surface) or the lock
breakage.
6.
Hold the tool firmly.
7.
Keep hands away from rotating parts.
8.
Make sure the wheel is not contacting the workpiece before the switch is
turned
9.
Before using the tool on an actual workpiece, let
for vibration or wobbling that could indicate poor installation or a poorly
balanced wheel.
IO.
Use the specified surface of the wheel to perform the grinding.
11.
Watch out for flying sparks. Hold the tool
and other persons or flammable materials.
12.
Do not leave the tool running. Operate the tool only when hand-held.
13.
Do not touch the workpiece immediately after operation;
hot and could burn your skin.
in
place.
marked on the tool's nameplate. When using depressed center
nut.
Damage to these parts could result
on.
it
run for a while. Watch
so
that sparks fly away from you
it
may be extremely
in
"No
wheel
SAVE THESE INSTRUCTIONS.
4
Loading...