Makita 9564P Owner's Manual

ENGLISH (Original instructions)

INSTRUCTION MANUAL

Angle Grinder

9564P
9565P

IMPORTANT: Read Before Using.

013574

DOUBLE INSULATION

1

ENGLISH (Original instructions)

SPECIFICATIONS

Depressed center wheel diameter 115 mm 125 mm

Rated speed (n)/ No load speed (n0) 12,000 min-1

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Symbols

The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Wear safety glasses.

･ Only for EU countries

Do not dispose of electric equipment
together with household waste
material!
In observance of European Directive
2012/19/EU on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible
recycling facility.

Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.

Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.

Model 9564P 9565P

Max. wheel thickness 6.4 mm

Spindle thread M14

Overall length 307 mm

Net weight 2.3 kg 2.4 kg

Safety class /II

END202-7

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

ENE048-1

ENF002-2

operating a power tool. Distractions can cause
you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

2

GEA005-3

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always
recommended.

Personal safety

11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools

with your finger on the switch or energising power
tools that have the switch on invites accidents.

14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.

15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

16.

Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts.

or long hair can be caught in moving parts.

17.

If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.

dust collection can reduce dust-related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

Loose clothes, jewellery

Use of

19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.

20. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

21. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

22. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many

accidents are caused by poorly maintained power
tools.

23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the

power tool for operations different from those
intended could result in a hazardous situation.

Service

25. Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the

safety of the power tool is maintained.

26. Follow instruction for lubricating and

changing accessories.

27. Keep handles dry, clean and free from oil and
grease.

GEB033-7

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool.
Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions

listed below may result in electric shock, fire
and/or serious injury.

2. Operations such as polishing are not

recommended to be performed with this
power tool. Operations for which the power tool

3

was not designed may create a hazard and cause
personal injury.

3. Do not use accessories which are not

specifically designed and recommended by
the tool manufacturer. Just because the

accessory can be attached to your power tool, it
does not assure safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on
the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of

your accessory must be within the capacity
rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or
controlled.

6. Threaded mounting of accessories must

match the grinder spindle thread. For
accessories mounted by flanges, the arbour
hole of the accessory must fit the locating
diameter of the flange. Accessories that do not

match the mounting hardware of the power tool
will run out of balance, vibrate excessively and
may cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed for
one minute. Damaged accessories will normally

break apart during this test time.

8. Wear personal protective equipment.

Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must

be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.

9. Keep bystanders a safe distance away from

work area. Anyone entering the work area
must wear personal protective equipment.

Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.

10. Hold the power tool by insulated gripping

surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.

11. Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.

12. Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.

13. Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.

14. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.

15. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.

Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel that is
entering into the pinch point can dig into the surface of
the material causing the wheel to climb out or kick out.
The wheel may either jump toward or away from the
operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels
may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.

The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b)

Never place your hand near the rotating

accessory.

Accessory may kickback over your hand.

4