Makita 906H User Manual

Page 1
Die Grinder
1/4” MODEL 906H
INSTRUCTION MANUAL
WARNING:
For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Page 2
SPECIFICATIONS
Model 906H
Collet size 1/4”
No load speed (RPM) 30,000/min.
Overall length 355 mm (14”)
Net weight 1.9 kg (4.2 lbs)
• Manufacturer reserves the right to change specifications without notice.
• Specifications may differ from country to country.
GENERAL SAFETY RULES
USA001-2
(For All Tools)
WARNING:
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work A re a
1.
Keep your work area clean and well lit.
Cluttered benches and dark areas invite acci­dents.
2.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Powe r
tools create sparks which may ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool. Distrac-
tions can cause you to lose control.
Electrical Safety
4.
Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordi­nances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically mal-
function or break down, grounding provides a low resistance path to carry electricity away from the user.
2
Page 3
5.
Avoid body contact with grounded sur­faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is grounded.
6.
Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
8.
When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
Personal Safety
9.
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
10.
Dress properly. Do not wear loose cloth­ing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
11.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.
12.
Remove adjusting keys or wrenches before turning the tool on. A wrench or a
key that is left attached to a rotating part of the tool may result in personal injury.
13.
Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
14.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection.
Tool Use and Care
15.
Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or
against your body is unstable and may lead to loss of control.
16.
Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
17.
Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
18.
Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.
Such preventive safety measures reduce the risk of starting the tool accidentally.
19.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
20.
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely to bind and are easier to control.
21.
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool ser­viced before using. Many accidents are
caused by poorly maintained tools.
22.
Use only accessories that are recom­mended by the manufacturer for your model. Accessories that may be suitable for
one tool, may become hazardous when used on another tool.
3
Page 4
24.
SERVICE
23.
Tool service must be performed only by qualified repair personnel. Service or main-
tenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury.
USE PROPER EXTENSION CORD: Use only three-wire extension cords that have three­prong grounding-type plugs and three-pole receptacles that accept the tool's plug. Make sure your extension cord is in good condition. Replace or repair damaged or worn cord immediately. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Table 1: Minimum gage for cord
Ampere Rating
More Than Not More Than AWG
0 6 18 16 16 14
6 10 18161412 10 12 16 16 14 12 12 16 14 12 Not Recommended
Volts Total length of cord in feet
120 V 25 ft. 50 ft. 100 ft. 150 ft.
GROUNDING INSTRUCTIONS
This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Never connect the green (or green and yellow) wire to a live terminal. Your unit is for use on 120 volts and has a plug that looks like Fig. “A”.
4
Page 5
An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two-prong receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con­nected to a permanent ground, such as a properly grounded outlet box.
Adapter
Grounding Means
Grounding
Blade
Cover of Grounded
Outlet Box
Fig. A Fig. B Fig. C
SPECIFIC SAFETY RULES
USB006-2
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to grinder safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.
1.
Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running
over rated speed can fly apart and cause injury.
2.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live” and shock the operator.
3.
Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses.
4.
Check the wheel carefully for cracks or damage before operation. Replace
cracked or damaged wheel immediately. Run the tool at no load for about a minute, holding tool away from others. If wheel is flawed, it will likely separate during this test.
5.
Hold the tool firmly.
6.
Keep hands away from rotating parts.
7.
Make sure the wheel is not contacting the workpiece before the switch is turned on.
8.
Before using the tool on an actual work­piece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel.
5
Page 6
9.
Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials.
10.
Do not leave the tool running. Operate the tool only when hand-held.
11.
Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin.
12.
Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
13.
Do not use water or grinding lubricant.
14.
Do not use this tool as cutter.
15.
ALWAYS wear proper apparel including long sleeve shirts, leather gloves and shop aprons to protect skin from contact with hot grindings.
16.
Use of this tool to grind or sand some products, paints and wood could expose user to dust containing hazardous sub­stances. Use appropriate respiratory pro­tection.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
6
Page 7
FUNCTIONAL DESCRIPTION
1. Switch lever
1
CAUTION:
Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.
Switch action
CAUTION:
Before plugging in the tool, always check to see that the tool is switched off.
Switch can be locked in ON position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool.
To start the tool, move the switch lever to the “ON” position. To stop the tool, move the switch lever to the “OFF” position.
ASSEMBLY
1
1. Wrench 17
2. Wrench 10
3. Collet nut
10 mm (3/8) Max.
003492
2
3
CAUTION:
Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing or removing wheel point
Loosen the collet nut and insert the wheel point into the collet nut. Use the smaller wrench to hold the spindle and the larger one to tighten the collet nut securely.
The wheel point should not be mounted more than 10 mm (3/ 8) from the collet nut. Exceeding this distance could cause vibration or a broken shaft. To remove the wheel point, follow the installation procedure in reverse.
CAUTION:
A 1/4 collet cone is provided as standard equipment. Use an optional collet cone 1/8 to install a 1/8 shank wheel point.
7
Page 8
OPERATION
1
1. Dressing stone
Turn the tool on without the wheel point making any contact with the workpiece and wait until the wheel point attains full speed. Then apply the wheel point to the workpiece gently. To obtain a good finish, move the tool in the leftward direction slowly.
CAUTION:
Apply light pressure on the tool. Excessive pressure on the tool will only cause a poor finish and overloading of the motor.
Dressing wheel point
When the wheel point becomes “loaded” with various bits and particles, you should dress the wheel point with the dressing stone.
MAINTENANCE
1
1. Limit mark
8
CAUTION:
Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden­tical carbon brushes.
Page 9
1. Brush holder cap
2. Screwdriver
003489
Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure
1
the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs, any
2
other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES
CAUTION:
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita service center.
Wheel points
Collet cone (1/4", 1/8")
Wrench 10
Wrench 17
Dressing stone
9
Page 10
Memo
10
Page 11
Memo
11
Page 12
Memo
12
Page 13
Cut
Makita U.S.A., Inc.
14930 Northam Street La Mirada, CA 90638-5753
Fold
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
13
Page 14
MAIL THIS PORTION
Your answers to the following questions are appreciated.
1. This product was purchased from:
Home Center
Hardware/Lumber Store
Tool Distributor
Industrial Supply
Construction Supply
2. Use of the product is intended for:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Other ( )
5. Any comments:
DATE PURCHASED MODEL NO.
MONTH DAY YEAR
INTL. LAST NAME / COMPANY NAME
Other ( )
3. How did you learn about this product:
4. Most favored points are:
SERIAL NO.
Magazine
From Dealer
Newspaper
Store Display
Catalog
Design
Features
Size
Price
Makita Brand
Radio
Exhibition
From Friend
Previous Usage
Other ( )
Repair Service
Durability
Powe r
Other ( )
STATUS
Married
Single
SEX
MF
STREET ADRESS
CITY
AREA
S TATE
AGE:
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Paste Paste Paste Paste Paste Paste
14
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
ZIP CODE PHONE
Under 19 20-29 30-39 40-49 50-60 Over 60
CODE
Paste Paste Paste Paste Paste Paste Paste Paste
Paste Paste Paste Paste Paste Paste
Page 15
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ARIZONA
3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850
CALIFORNIA
41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881
14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088
1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197
7674 Clairemont Mesa Blvd. San Diego, CA 92111 (858) 278-4471
16735 Saticoy St., Ste. 105 Van Nuys, CA 91406 (818) 782-2440
COLORADO
11839 E. 51st Ave. Denver, CO 80239-2709 (303) 371-2850
FLORIDA
750 East Sample Road Pompano Beach, FL 33064 (954) 781-6333
GEORGIA
4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911
ILLINOIS
1450 Feehanville Dr. Mt. Prospect, IL 60056-6011 (847) 297-3100
MARYLAND
7397 Washington Boulevard, Suite 104 Elkridge, MD 21075 (410) 796-4401
MASSACHUSETTS
232 Providence Hwy. Westwood, MA 02090 (781) 461-9754
MINNESOTA
6427 Penn Ave. South Richfield, MN 55423 (612) 869-5199
MISSOURI
9876 Watson Road St. Louis, MO 63126-2221 (314) 909-9889
NEBRASKA
4129 S. 84th St. Omaha, NE 68127 (402) 597-2925
NEVADA
3375 S. Decatur Blvd. Suites. 22 - 24 Las Vegas, NV 89102 (702) 368-4277
NEW JERSEY
251 Herrod Blvd. Dayton, NJ 08810-1539 (609) 655-1212
NEW YORK
4917 Genessee Street Cheektowaga, NY 14225 (716) 685-9503
OREGON
828 19th Avenue, N.W. Portland, OR 97209 (503) 222-1823
PENNSYLVANIA
1704 Babcock Blvd. Pittsburgh, PA 15209 (412) 822-7370
PUERTO RICO
200 Guayama St. Hato Rey, PR 00917 (787) 250-8776
TENNESSEE
1120 Elm Hill P. Suile 170 Nashville, TN 372 (615) 248-3321
TEXAS
12801 Stemmons Fwy Ste. 809 Farmers Branch, TX 75234 (972) 243-1150
12701 Directors Dr. Stafford, TX 77477-3701 (281) 565-8665
3453 IH-35 North, Ste. 101 San Antonio, TX 78219 (210) 228-0676
WISCONSIN
Lincoln Plaza Shopping Ctr. 2245 S. 108th St. West Allis, WI 53227 (414) 541-4776
CUSTOMER’S RECORD
When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of the carton detailing the problem with your tool.
Date Purchased
Dealer’s Name & Address
Model No.
Serial No.
15
Page 16
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wear and tear:
the tool has been abused, misused or improperly maintained:
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
883498C066
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
Loading...