Makita 8411DW, 8411D User Manual
Cordless Hammer Drill
Equipped with electric brake
MODEL 8411D
MODEL 8411DW
With Fast Charger
INSTRUCTION MANUAL
Steel Wood Wood
10
mm
(3/8”) 21
0
~
12,700 1.87
Voltage
mm
Capacities
I13/16”) 71;4m:
0
~
4,100
screw
~~~~1~~
273
mm
x
110-3/4” x 3-1/8”
Input output Charging time
79
mm
Concrete
10
x
mm
x
220
(3/8”)
8-5/8”)
mm
Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
No load speed
High
0
~
1,150
kg
(RPM)
LOW
0
--
(4 2 Ibs)
370
I
M
PO
RTANT
SAFETY
WARNING:
PRECAUTIONS SHOULD ALWAYS
WHEN USING ELECTRIC TOOLS, BASIC SAFETY
I
N
(For
STRUCTI
All
Tools)
BE
FOLLOWED TO REDUCE
0
N
S
THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
ALL
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
or wet locations.*Keep work area well
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place
DON'T FORCE TOOL.
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in
moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
DON'T OVERREACH. Keep proper footing and balance at
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and
rized service facility. Inspect extension cords periodically and replace
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not
ing accessories, such as blades, bits, cutters.
INSTRUCTIONS.
lit.
Don't expose power tools to rain.
-
out of reach of children.
It
will do the job better and safer at the rate for which
it
frees both hands to operate tool.
if
damaged, have repaired
in
use, before servicing, and when chang-
in
damp
if
cutting operation is
it
to disconnect from
all
times.
by
autho-
if
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger
on switch. Be sure switch is OFF when plugging
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
17.
STAY ALERT. Watch what you are doing, use common sense. Don’t operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Don’t
use tool
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
the tool.
voltage less than the nameplate rating is harmful to the motor.
if
switch does not turn
If
in doubt, DO NOT PLUG IN THE TOOL. Using a power source with
it
on and off.
in.
so
marked.
-
as well as damage to
it
will
3
IMPORTANT
I.
SAVE
THESE INSTRUCTIONS
SAFETY
INSTRUCTIONS
-
This manual
Length of Cord (Feet)
AWG Size of Cord
Do not operate charger with damaged cord or plug - replace them
9.
mediately.
IO.
Do not operate charger if
otherwise damaged
11.
Do not disassemble charger
serviceman when service or repair is required. Incorrect reassembly may
in
result
12.
To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning
4
a risk of electric shock or fire.
it
has received a sharp blow, been dropped, or
in
any way; take
or
25 50 100 150
18 18 18 16
it
to a qualified serviceman.
battery cartridge; take
off
controls
will
not reduce this risk.
it
to a qualified
im-
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1.
Do
not charge Battery Cartridge when temperature is BELOW 10°C
or ABOVE 4OoC (104OF).
2.
Do
not attempt to use a step-up transformer, an engine generator or DC power
receptacle.
3.
Do
not allow anything to cover or clog the charger vents.
4.
Always cover the battery terminals with the battery cover when the battery
cartridge is not used.
5.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
(1)
Do
not touch the terminals with any conductive material.
(2)
Avoid storing battery cartridge in a container with other metal objects such
as nails, coins, etc.
(3)
Do
not expose battery cartridge to water or rain.
6.
Do
not store the tool and Battery Cartridge
ture may reach or exceed 5OoC (122OF).
7.
Do
not incinerate the Battery Cartridge even if
completely worn out. The battery cartridge can explode
in
locations where the tempera-
it
is severely damaged or is
in
a fire.
ADDITIONAL SAFETY RULES
1.
Be aware that this tool is always
not have to be plugged into an electrical outlet.
2.
Wear a hard hat (safety helmet), safety glasses and/or face shield.
highly recommended that you wear a dust mask, ear protectors and thickly
padded gloves.
3.
Under normal operation, the tool is designed to produce vibration. The screws
can come loose easily, causing a breakdown or accident. Check tightness of
screws carefully before operation.
4.
Always be sure you have a firm footing.
no
Be sure
5. Hold the tool firmly.
6.
Keep hands away from rotating parts.
7.
Do
not leave the tool running. Operate the tool only when hand-held.
8.
When drilling into walls, floors or wherever "live" electrical wires may be
encountered,
Hold the tool by the insulated grasping surfaces to prevent electric shock if
you drill into a "live" wire.
9.
Do
not touch the bit or the workpiece immediately after operation; they may
be extremely hot and could burn your skin.
one is below when using the tool
DO NOT
TOUCH ANY METAL PARTS OF THE TOOL!
in
an operating condition, because
in
high locations.
It
(5OOF)
it
does
is also
SAVE THESE INSTRUCTIONS.
5
Loading...