Makita 6953 User Manual
Impact Wrench
MODEL 6953
DOUBLE
INSULATION
INSTRUCTION MANUAL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
SPECIFICATIONS
Capacities
Standard bolt
10mm - 16mm
(3/8”- 5/8”)
High tensile
bolt
8mm - 12mm
(5/16” - 1/2”)
No load
speed (RPM)
0 - 3000/min. 0 - 3000
Impacts per
minute
Max. fasten-
ing torque
150 N • m
(111ft • lbs)
Overall length Net weight
233 mm
(9-1/8”)
1.4kg(3lbs)
• Manufacturer reserves the right to change specifications without notice.
• Specifications may differ from country to country.
GENERAL SAFETY RULES
USA002-2
(For All Tools)
WARNING:
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work Ar ea
1.
Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.
tools create sparks which may ignite the dust
or fumes.
3.
Keep bystanders, children, and visitors
away while operating a power tool.
tions can cause you to lose control.
Electrical Safety
2
Powe r
Distrac-
4.
Double insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way.
tion eliminates the need for the three wire
grounded power cord and grounded power
supply system.
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators.
electric shock if your body is grounded.
There is an increased risk of
Double insula-
6.
Do not expose power tools to rain or wet
conditions.
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately.
cords increase the risk of electric shock.
8.
When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”.
use and reduce the risk of electric shock.
Water entering a power tool will
These cords are rated for outdoor
Personal Safety
9.
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication.
operating power tools may result in serious
personal injury.
10.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts.
hair can be caught in moving parts.
11.
Avoid accidental starting. Be sure switch
is off before plugging in.
your finger on the switch or plugging in tools
that have the switch on invites accidents.
12.
Remove adjusting keys or wrenches
before turning the tool on.
key that is left attached to a rotating part of
the tool may result in personal injury.
13.
Do not overreach. Keep proper footing
and balance at all times.
balance enables better control of the tool in
unexpected situations.
14.
Use safety equipment. Always wear eye
protection.
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
A moment of inattention while
Loose clothes, jewelry, or long
Carrying tools with
A wrench or a
Proper footing and
Dust mask, non-skid safety
Damaged
Tool Use and Care
15.
Use clamps or other practical way to
secure and support the workpiece to a
stable platform.
against your body is unstable and may lead
to loss of control.
16.
Do not force tool. Use the correct tool for
your application.
job better and safer at the rate for which it is
designed.
17.
Do not use tool if switch does not turn it
on or off.
with the switch is dangerous and must be
repaired.
18.
Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
19.
Store idle tools out of reach of children
and other untrained persons.
dangerous in the hands of untrained users.
20.
Maintain tools with care. Keep cutting
tools sharp and clean.
tools with sharp cutting edges are less likely
to bind and are easier to control.
21.
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool serviced before using.
caused by poorly maintained tools.
22.
Use only accessories that are recommended by the manufacturer for your
Accessories that may be suitable for
model.
one tool, may become hazardous when used
on another tool.
Holding the work by hand or
The correct tool will do the
Any tool that cannot be controlled
Properly maintained
Many accidents are
SERVICE
23.
Tool service must be performed only by
qualified repair personnel.
tenance performed by unqualified personnel
could result in a risk of injury.
Service or main-
To ol s a r e
3
24.
When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Table 1: Minimum gage for cord
Ampere Rating
More Than Not More Than
0 6 18 16 16 14
6 10 18161412
10 12 16 16 14 12
12 16 14 12 Not Recommended
Volts Total length of cord in feet
120 V 25 ft. 50 ft. 100 ft. 150 ft.
AWG
SPECIFIC SAFETY RULES
USB003-2
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to impact wrench safety
rules. If you use this tool unsafely or incorrectly, you can suffer
serious personal injury.
1.
Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or
its own cord.
make exposed metal parts of tool “live” and
shock the operator.
2.
Wear ear protectors.
3.
Check the socket carefully for wear,
cracks or damage before installation.
4.
Hold the tool firmly.
Contact with a “live” wire will
4
5.
Always be sure you have a firm footing.
Be sure no one is below when using the
tool in high locations.
6.
The proper fastening torque may differ
depending upon the kind or size of the
bolt. Check the torque with a torque
wrench.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
SYMBOLS
The followings show the symbols used for tool.
....................... volts
V
....................... amperes
A
..................... hertz
Hz
................ alternating current
....................no load speed
n
˚
....................Class II Construction
................revolutions or reciprocation per
.../min
minute
................number of blow
USD202-2
5
Loading...