Makita 6891DW, 6891D User Manual
Cordless Drywall Screwdriver
-
Equipped with Electric Brake
MODEL 6891D
MODEL 6891DW
With
Fast
Charger
INSTRUCTION MANUAL
SPEC
IF
I
CAT
Capacity
Drywall screw
4
mm 15132"l
Battery Cartridge
Voltage
9.6 V
I
0
N
S
No load speed IRPMI
9000
0
--
1,400
Model DC9700 Fast Charger
Input output Charging time
A.C. only 50 Hz
230
~
60
Dimensions
mm
x
55 mm x 260 mm
19"
x
2-118'' x 10-1/4"1
Hr
D.C.
(L
x W x
7
HI
2 V. 9.6 V
Net weight
,3
kg
,2,9
1
Hr.
,bsl
IMPORTANT
SAFETY INSTRUCTIONS
(For
All
Tools)
WARNING:
TY PRECAUTIONS SHOULD ALWAYS
WHEN USING ELECTRIC TOOLS, BASIC SAFE-
BE
FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
2.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp
or wet locations. Keep work area well
Don't use tool in presence of flammable liquids or gases.
3.
KEEP CHILDREN AWAY.
Don't let visitors contact tool or extension cord.
4.
STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place
5.
DON'T FORCE TOOL.
it
was intended.
6.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
7.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is
8.
dusty.
9.
DON'T ABUSE CORD. Never carry tool by cord or yank
receptacle. Keep cord from heat, oil, and sharp edges.
IO.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
11.
DON'T OVERREACH. Keep proper footing and balance at all times.
12.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and
rized service facility. Inspect extension cords periodically and replace if
damaged. Keep handles dry. clean, and free from oil and grease.
13.
DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.
it
frees both hands to operate tool.
All
visitors should be kept away from work area.
-
out
of
reach of children.
It
will do the job better and safer at the rate for which
lit.
Don't expose power tools to rain.
it
to disconnect from
if
damaged, have repaired by autho-
2
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger
on switch. Be sure switch is OFF when plugging in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
so
extension cords intended for use outdoors and
17.
STAY
ALERT.
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere
Have defective switches replaced
if
tool
IS.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user
the
tool. If
voltage less than the nameplate rating is harmful to
Watch what you are doing, use common sense. Don't operate
by
authorized service center. Don't use
switch does not turn
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source with
it
on and off.
marked.
of
parts, mounting, and any
in
this instruction manual.
-
as well as damage to
the
motor.
it
will
3
IMPORTANT SAFETY INSTRUCTIONS
1.
SAVE
contains important safety and operating instructions for battery charger.
2.
Before using battery charger, read all instructions and cautionary markings
on
(1)
3.
CAUTION - To reduce risk of injury, charge only MAKITA Battery
9000
and damage.
4.
Do not expose charger to rain or snow.
5.
Use of an attachment not recommended or sold by the battery charger
manufacturer may result
6.
To reduce risk of damage to electric plug and cord, pull by plug rather than
cord when disconnecting charger.
7.
Make sure cord is located
or otherwise subjected to damage or stress.
8.
An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock.
extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape
as those of plug on charger;
b. That extension cord is properly wired and
c. That wire size is at least as large as the one specified
THESE
battery charger,
or
9100.
Other types of batteries may burst causing personal injury
RECOMMENDED MINIMUM AWG
EXTENSION CORDS
INSTRUCTIONS
(2)
battery, and
in
a risk of fire, electric shock, or injury to persons.
so
that
TABLE
(3)
product using battery.
it
will not be stepped on, tripped over,
in
good electrical condition; and
1
SIZE
FOR
BATTERY CHARGERS
-
This manual
in
the table below.
FOR
7000,
If
Length of Cord (Feet)
AWG Size of Cord
9.
Do not operate charger with damaged cord or plug - replace them immediately.
IO.
Do not operate charger
otherwise damaged in any way; take
11.
Do not disassemble charger or battery cartridge; take
serviceman when service or repair is required. Incorrect reassembly may
result
in
a risk of electric shock or fire.
12.
To reduce risk
ing any maintenance or cleaning. Turning off controls will not reduce this risk.
4
of
electric shock, unplug charger from outlet before attempt-
if
it
has received a sharp blow, been dropped, or
25
50
100
18 18 18
it
to a qualified serviceman.
150
16
it
to a qualified
Loading...