ENGLISH
Cordless Auto Feed
Screwdriver
MODEL 6835D
INSTRUCTION MANUAL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
001872
SPECIFICATIONS
Model 6835D
Screw strip 4 mm x 25 mm - 41 mm
No load speed (min-1)
Overall length 364 mm
Net weight 2.0 kg
Rated voltage D.C. 12V
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
..................Only for EU countries
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Do not dispose of electric equipment
together with household waste
material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life
must be collected separately and
returned to an environmentally
compatible recycling facility.
END001-1
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is not more
than 70 dB (A).
The noise level under working may exceed 85 dB (A).
– Wear ear protection. –
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standardized documents;
EN60745, EN55014 in accordance with Council Directives, 89/336/EEC, 98/37/EC.
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
Yasuhiko Kanzaki CE2005
2,000
Director
2
.
2
GENERAL SAFETY RULES GEA002-3
WARNING:
Read all instructions. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains-operated (corded) power tool or batteryoperated (cordless) power tool.
SAVE THESE INSTRUCTIONS
Wor k a rea sa fet y
1. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
2. Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Personal safety
9. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
10. Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
11. Avoid accidental starting. Ensure the switch is
in the off-position before plugging in. Carrying
power tools with your finger on the switch or plugging in power tools that have the switch on invites
accidents.
12. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
13. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
14. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
15. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
Power tool use and care
16. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
17. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
18. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
19. Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
3
20. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
21. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
22. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and in
the manner intended for the particular type of
power tool, taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
23. Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites accidents.
24. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
25. Use power tools only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a fire.
27. Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or
burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and changing
accessories.
30. Keep handles dry, clean and free from oil and
grease.
SPECIFIC SAFETY RULES GEB017-1
DO NOT let comfort or familiarity with product (gained from repeated use)
replace strict adherence to screwdriver safety rules. If you use this power
tool unsafely or incorrectly, you can suffer serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal
parts of the tool “live” and shock the operator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in this instruction manual
may cause serious personal injury.
4
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CARTRIDGE
1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the battery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
7. Do not store the tool and battery cartridge in
8. Do not incinerate the battery cartridge even if it
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
4. Charge the Nickel Metal Hydride battery car-
ENC004-1
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
locations where the temperature may reach or
exceed 50°C (122°F).
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
ture at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.
tridge when you do not use it for more than six
months.
5
FUNCTIONAL
DESCRIPTION
2
1. Button
2. Battery cartridge
1
1. Lever
2. Stopper base
3. Plate
4. Casing
CAUTION:
• Always be sure that the tool is switched off and the battery cartridge is
removed before adjusting or checking function on the tool.
001873
Installing or removing battery cartridge
• Always switch off the tool before insertion or removal of the battery
cartridge.
1
• To remove the battery cartridge, withdraw it from the tool while pressing
the push buttons on both sides of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge
with the groove in the housing and slip it into place. Always insert it all the
way until it locks in place with a little click. If not, it may accidentally fall
out of the tool, causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge
does not slide in easily, it is not being inserted correctly.
Setting for desired screw length
There are 3 positive-lock screw length settings. To obtain the desired setting,
001875
pull out the stopper base while depressing the lever until you see the number
of the desired screw length (indicated on the plate) appear to rest on the very
top edge of the casing.
2
See the table below for the relation between the number indicated on the plate
and the respective screw length ranges.
3
4
Number indicated on the plate Screw length range (mm)
25/28 25 - 28
32 28 -35
41 35 -41
006479
1
2
3
B
4
A
1. Approx. 5 mm
2. Stopper base
3. Casing
4. Adjusting knob
6
Adjusting the driving depth
005429
Depress the stopper base as far as it will go. While keeping it in this position,
turn the adjusting knob until the bit tip projects approx. 5 mm from the stopper
base. Drive a trial screw. If the screw head projects above the driving surface,
turn the adjusting knob in the A direction; if the screw head is countersunk,
turn the adjusting knob in the B direction.
001877
Switch action
1. Switch trigger
ASSEMBLY
1
2
1. Casing
2. Thumb screws
1 2 3
1
CAUTION:
• Before inserting the battery cartridge into the tool, always check to see
that the switch trigger actuates properly and returns to the “OFF” position
when released.
To start the tool, simply pull the switch trigger. Release the switch trigger to
stop.
CAUTION:
• Always be sure that the tool is switched off and the battery cartridge is
removed before carrying out any work on the tool.
Installing or removing the bit
001878
Loosen the thumb screws which secure the casing. Pull out the casing in the
direction of the arrow.
001879
Press the dust cover toward the plane bearing and pull out the bit. If the dust
cover cannot be moved as far as the plane bearing, try it again after turning
the bit slightly.
To install the bit, insert it into the socket while turning it slightly. After installing,
always make sure that the bit is securely held in place by trying to pull it out.
1. Bit
2. Dust cover
3. Plane bearing
7
1
2
3
1. Feeder box
2. Screw strip
3. Screw guide
1
1. Driving position
001880
Installing screw strip
Insert the screw strip through the screw guide. Then insert it through the
feeder box until the first screw reaches the position next to the driving position.
001881
Removing screw strip
001883
To remove the screw strip, just pull it out in the direction of the arrow.
1
1. Reverse button
8
If you depress the reverse button, you can pull out the screw strip in the
001882
reverse direction of the arrow.
1
1. Hook
OPERATION
Carry hook
001884
The carry hook is convenient for temporarily hooking the tool. It can be
installed on either side of the tool.
When installing or removing the carry hook, widen it by pressing its lower portion in the direction of the arrow.
001886
Driving operation
Switch on the tool by pulling the switch trigger. Hold the tool squarely and
firmly up against the driving surface. A screw will be automatically carried to
the driving position and fastened.
CAUTION:
• Always check the bit carefully for wear before driving operations. Replace
a worn bit or poor fastening may result.
• Always hold the tool squarely against the driving surface. Holding it at an
angle may damage the screw heads and cause wear on the bit. This may
also lead to poor fastening.
• Always keep the tool firmly against the driving surface until the driving is
over. Failure to do so may cause insufficient fastening of screws.
• Be careful not to drive a screw onto another screw already fastened.
• Do not operate the tool without screws. It will damage the driving surface.
• If the feeder box does not work smoothly when driving screws, spray car
wax (spray type) on the sliding surfaces. Never lubricate it.
1
15mm
1. Wall
2. Stopper base
MAINTENANCE
005333
Driving in corner
This tool can be used to drive at a position 15 mm away from the wall as
2
shown in the figure.
CAUTION:
• Driving at a position closer than 15 mm to the wall or driving with the
stopper base in contact with the wall may damage the screw heads and
cause wear on the bit. This may also lead to poor fastening of screws
and malfunction of the tool.
CAUTION:
• Always be sure that the tool is switched off and the battery cartridge is
removed before attempting to perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
9
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended for use with your Makita tool specified in this manual. The
use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita service center.
• Drywall screw strip
• Phillips bit
• Plastic carrying case
• Various type of Makita genuine batteries and
chargers
10
Memo
11
884269E228
Makita Corporation Anjo, Aichi, Japan
Loading...