Makita 6207D-NEW, 6317D-NEW, 6347D-NEW, 6337D-NEW Technical Information

T

ECHNICAL INFORMATION

Models No.

Description

6207D-NEW
6317D-NEW, 6337D-NEW, 6347D-NEW

9.6V Cordless Driver Drill 10mm (3/8”)
12V, 14.4V, 18V Cordless Driver Drills 13mm (1/2”)

CONCEPT AND MAIN APPLICATIONS

These four Cordless Driver Drills are redesigned with
the same aesthetic design concept as 6261D series models.
These four models are available in the following variations.

Model No.

6207DWDE

10mm

(3/8")

6207DWFE

6317DWAE

6317DWDE

6317DWFE

6337DWAE

13mm

6337DWDE

(1/2")

6337DWFE

6347DWAE

6347DWDE

6347DWFE

9134 (Ni-MH, 9.6V/ 2.6Ah)

9135 (Ni-MH, 9.6V/ 3.0Ah)

1222 (Ni-Cd, 12V/ 2.0Ah)

1234 (Ni-MH, 12V/ 2.6Ah)

1235 (Ni-MH, 12V/ 3.0Ah)

1422 (Ni-Cd, 14.4V/ 2.0Ah)

1434 (Ni-MH, 14.4V/ 2.6Ah)

1435 (Ni-MH, 14.4V/ 3.0Ah)

1822 (Ni-Cd, 18V/ 2.0Ah)

1834 (Ni-MH, 18V/ 2.6Ah)

1835 (Ni-MH, 18V/3.0Ah)

Type

Battery

Q’ty

2

2

2

2

2

2

2

2

2

2
2

All models also include the accessories listed below
in "Standard equipment".

Cover

2

2

2

2

2

2

2

2

2

2
2

Charger

DC1414

DC1414

DC1414

DC1414

DC1414

DC1414

DC1414

DC1414

DC1804

DC1804

DC1804

W

Dimensions: mm (")

10mm (3/8")

Model No.

Length (L)

Width (W)

Height (H)

*1: for USA, Canada, Mexico, Panama
*2: for all countries except the four listed above

6207D-NEW

*1

235

(9-1/4)

*2

233

(9-1/8)

78

(3-1/16)

252

(9-7/8)

6317D-NEW

244

(9-5/8)

241

(9-1/2)

95

(3-3/4)

256

(10-1/8)

13mm (1/2")

6337D-NEW

*1

*2

L

244

(9-5/8)

241

(9-1/2)

95

(3-3/4)

255

(10)

PRODUCT

P 1/ 8

H

6347D-NEW

*1

244

(9-5/8)

*2

241

(9-1/2)

95

(3-3/4)

258

(10-1/8)

*1

*2

Specification

10 mm

6207D-NEW

6317D-NEW

Ni-cd/ Ni-MH Ni-cd/ Ni-MH

9.6

12 1814.4

2.0/ 2.6/ 3.0 2.0/ 2.6/ 3.0
45/ 60/ 70

with DC1804

Specification

Type of cell

Voltage: V

Battery

Capacity: Ah

Charging time (approx.): min.

Model No.

Max output (W) 160 205 230 305
Chuck capacity: mm (")

Type of keyless drill chuck

Drilling capacity: mm (")

Steel
Wood

No load speed: rpm = min -1

High

Low

Lock torque: N.m (in.lbs)

Max. fastening torque:
N.m (in.lbs)

Hard joint
Soft joint

Torque settings

Electric brake
LED job light
Belt clip
Externally accessible carbon brush

Rubberized soft grip

Net weight*: kg (lbs)

1-10 (1/32-3/8)

Dual sleeve

10 (3/8)

25.4 (1)

0 - 1,400

0 - 450

25.4 (1)
0 - 1,400

0 - 450

35 (310)
50 (440)
20 (180)

60 (530)

25 (220)

16 stages

( + drill mode)

Yes

No

No
Yes
Yes

1.8 (4.0) 2.0 (4.4) 2.1 (4.6) 2.3 (5.1)

*Weight according to EPTA-Procedure 01/2003, including battery

13 mm

6337D-NEW 6347D-NEW

45/ 60/ 70

with DC1804

1.5-13 (1/16-1/2)

Dual sleeve

13 (1/2)

32 (1-1/4) 38 (1-1/2)

40 (350) 45 (400)
65 (580)
30 (270)

16 stages

( + drill mode)

Yes

No

No
Yes
Yes

0 - 1,600

0 - 500

80 (710)
35 (310)

Standard equipment

+- bit 2-45, Plastic carrying case

Note: The standard equipment for the tool shown above may vary by country.

Optional accessories

P 2/ 8

Model No.

6207D-NEW

6317D-NEW

6337D-NEW

6347D-NEW

Battery

9120, 9122, 9134, 9135, 9135A, PA09

1220, 1222, 1234, 1235, 1235A, PA12

1420, 1422, 1434, 1435, PA14

1822, 1834,1835, PA18

Charger

DC1414, DC1439, DC1804, DC1822

DC1804, DC1822

Repair

< 1 > Disassembling of drill chuck See Fig. 1.
For replacing gear assembly, drill chuck has to be disassembled.
Take the following steps.

1. Firmly hold No.1R139 "Drill chuck extractor" with vise. And lock spindle with the drill chuck extractor.

2. Open the jaws of drill chuck fully and take off flat head screw M6 x 22 by turning clockwise.

3. Disassemble drill chuck with hex wrench inserted into drill chuck by turning the hex wrench anti-clockwise.

If drill chuck is damaged, firmly hold the drill chuck with vise and turn spindle with wrench anti-clockwise
as illustrated in fig. 1A.

P 3/ 8

1R139 Drill chuck extractor

Fig. 1

< Note >
For replacing other than gear assembly, it is not necessary to disassemble drill chuck.

< 2 > Disassembling housing See Fig. 2.

1. Take off brush holder caps and carbon brushes.

2. Slide mode change lever to the drill mode side.

3. Unscrew ten PT3x16 Tapping screws.

Mode change lever

Slide mode change lever
to the drill mode side.

Carbon brush

Tapping screw bind
PT 3x16 (10 pcs)

Fig. 1A

Brush holder cap

Carbon brush

Brush holder cap

Fig. 2