Makita 6328D, 6327D User Manual

Page 1
GB
Cordless Driver Drill Instruction Manual
F
Perceuse-visseuse sans fil Manuel d’instructions
D
Akku-Bohrschrauber Betriebsanleitung
I
Trapano-avvitatore a batteria Istruzioni per l’uso
Snoerloze boor-schroevedraaier Gebruiksaanwijzing
E
Taladro-atornillador a batería Manual de instrucciones
P
Berbequim aparafusador a bateria Manual de instruções
DK
Akku bore-skruemaskine Brugsanvisning
S
Sladdlös borrmaskin/skruvdragare Bruksanvisning
N
Akku boreskrutrekker Bruksanvisning
SF
Akkuporakone Käyttöohje
GR Βιδοτρύπανο µε µπαταρία Οδηγίες χρήσεως
12 V 6327D
14.4 V 6328D
Page 2
1
3
4 5
2
12
7
16
14
12
6
89
6 1
14
12
7
1110
34
16
15
12 13
16
16
14
17
18
56
16
7
2
Page 3
ENGLISH
Explanation of general view
1 Button 2 Battery cartridge 3Tighten 4Sleeve 5 Ring 6 Switch trigger
SPECIFICATIONS
Model 6327D 6328D
Capacities
Steel .........................................................................................13 mm 13 mm
Wood ........................................................................................24 mm 24 mm
Wood screw ..............................................................................5.1 mm x 63 mm 5.1 mm x 63 mm
No load speed (min
High ..........................................................................................0 – 1,100 0 – 1,100
Low ...........................................................................................0 – 350 0 – 350
Overall length ..............................................................................220 mm 220 mm
Net weight.....................................................................................1.6 kg 1.7 kg
Rated voltage ..............................................................................D.C. 12 V D.C. 14.4 V
-1
)
7 Reversing switch lever 8A side 9B side 10 Clockwise 11 Counterclockwise 12 Low speed
13 High speed 14 Speed change lever 15 Adjusting ring 16 Graduations 17 Drill marking 18 Pointer
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood, metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using bat­tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain. A battery short can cause a large current flow, overheating, possible burns and even a break­down.
ENC004-1
7. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the bat­tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera­ture at 10°C – 40°C (50°F – 104°F). Let a hot bat­tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car­tridge when you do not use it for more than six months.
ADDITIONAL SAFETY RULES
1. Be aware that this tool is always in an operating condition, because it does not have to be plugged into an electrical outlet.
2. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.
3. Always be sure you have a firm footing.
4. Be sure no one is below when using the tool in high locations.
5. Hold the tool firmly.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool only when hand-held.
ENB022-1
3
Page 4
8. Do not touch the drill bit or the workpiece imme­diately after operation; they may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the car­tridge.
• To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being inserted correctly.
Installing or removing driver bit or drill bit (Fig. 2)
Important: Always be sure that the tool is switched off and the bat­tery cartridge is removed before installing or removing the bit.
Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clock­wise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve coun­terclockwise.
Switch action (Fig. 3)
CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
To start the tool, simply pull the trigger. Tool speed is increased by increasing pressure on the trigger. Release the trigger to stop.
Reversing switch action (Fig. 4)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counter­clockwise rotation. When the switch lever is in the neutral position, the switch trigger cannot be pulled.
Speed change (Fig. 5)
To change the speed, first switch off the tool and then slide the speed change lever to the “II” side for high speed or “I” side for low speed. Be sure that the speed change lever is set to the correct position before opera­tion. Use the right speed for your job.
CAUTION:
• Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned half-way between the “ I ” side and “II” side, the tool may be damaged.
• Do not use the speed change lever while the tool is run­ning. The tool may be damaged.
Adjusting the fastening torque (Fig. 6)
The fastening torque can be adjusted in 17 steps by turn­ing the adjusting ring so that its graduations are aligned with the pointer on the tool body. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. The clutch is designed not to slip at the
A marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.
NOTE: Do not operate the tool with the adjusting ring set between the number 16 and the be damaged.
Screwdriving operation (Fig. 7)
Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in.
NOTE:
• Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
• When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart below.
Nominal diameter of
wood screw (mm)
3.1 2.0 – 2.2
3.5 2.2 – 2.5
3.8 2.5 – 2.8
4.5 2.9 – 3.2
4.8 3.1 – 3.4
5.1 3.3 – 3.6
5.5 3.6 – 3.9
5.8 4.0 – 4.2
6.1 4.2 – 4.4
• If the tool is operated continuously until the battery car­tridge has discharged, allow the tool to rest for 15 min­utes before proceeding with a fresh battery.
marking is aligned with the
A
A marking. The tool may
Recommended size of
pilot hole (mm)
4
Page 5
Drilling operation
First, turn the adjusting ring so that the pointer on the tool body points to the
• Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece.
• Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry.
CAUTION:
• Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool perfor­mance and shorten the service life of the tool.
• There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
• A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly.
• Always secure small workpieces in a vise or similar hold-down device.
• If the tool is operated continuously until the battery car­tridge has discharged, allow the tool to rest for 15 min­utes before proceeding with a fresh battery.
A marking. Then proceed as follows.
MAINTENANCE
CAUTION: Always be sure that the tool is switched off and the bat­tery cartridge is removed before carrying out any work on the tool.
To maintain product safety and reliability, repairs, mainte­nance or adjustment should be carried out by a Makita Authorized Service Center.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita service center.
•Screw bits
• Rubber pad assembly
• Foam polishing pad 125
• Wool bonnet 100
• Various type of Makita genuine batteries and chargers
• Plastic carrying case
5
Page 6
NEDERLANDS
Verklaring van algemene gegevens
1 Knop 2 Accu 3 Vastdraaien 4Bus 5 Ring 6 Trekschakelaar
TECHNISCHE GEGEVENS Model 6327D 6328D
Capaciteiten
Staal ......................................................................................... 13 mm 13 mm
Hout .......................................................................................... 24 mm 24 mm
Houtschroef .............................................................................. 5,1 mm x 63 mm 5,1 mm x 63 mm
Toerental onbelast (min
Hoog ......................................................................................... 0 – 1 100 0 – 1 100
Laag ......................................................................................... 0 – 350 0 – 350
Totale lengte ................................................................................220 mm 220 mm
Netto gewicht ...............................................................................1,6 kg 1,7 kg
Nominale spanning .....................................................................D.C. 12 V D.C. 14,4 V
-1
)
7 Omkeerschakelaar 8 Zijde A 9 Zijde B 10 Rechtse draairichting 11 Linkse draairichting 12 Laag toerental
13 Hoog toerental 14 Toerentalschakelaar 15 Stelring 16 Schaalverdelingen 17 Boormarkering 18 Wijzer
• In verband met ononderbroken research en ontwikke-
ling behouden wij ons het recht voor bovenstaande
technische gegevens te wijzigen zonder voorafgaande
kennisgeving.
• Opmerking: De technische gegevens kunnen van land
tot land verschillen.
Doeleinden van gebruik
Dit gereedschap is bedoeld voor het boren en het indraaien van schroeven in hout, metaal en plastic.
Veiligheidswenken
Voor uw veiligheid dient u de bijgevoegde Veiligheids­voorschriften nauwkeurig op te volgen.
BELANGRIJKE VEILIGHEIDSVOORSCHRIFTEN VOOR ACCULADER EN ACCU
1. Lees alle voorschriften en waarschuwingen op
(1) de acculader, (2) de accu, en (3) het product waarvoor de accu wordt gebruikt, aandachtig door alvorens de acculader in gebruik te nemen.
2. Neem de accu niet uit elkaar.
3. Als de gebruikstijd van een opgeladen accu aan-
zienlijk korter is geworden, moet u het gebruik ervan onmiddellijk stopzetten. Voortgezet gebruik kan oververhitting, brandwonden en zelfs een ontploffing veroorzaken.
4. Als er elektrolyt in uw ogen is terechtgekomen,
spoel dan uw ogen met schoon water en roep onmiddellijk de hulp van een dokter in. Elektrolyt in de ogen kan blindheid veroorzaken.
5. Bedek de accuklemmen altijd met de accukap
wanneer u de accu niet gebruikt.
6. Voorkom kortsluiting van de accu: (1) Raak de accuklemmen nooit aan met een
geleidend materiaal.
(2) Bewaar de accu niet in een bak waarin
andere metalen voorwerpen zoals spijkers,
munten e.d. worden bewaard. (3) Stel de accu niet bloot aan water of regen. Kortsluiting van de accu kan oorzaak zijn van een grote stroomafgifte, oververhitting, brand-
wonden, en zelfs defecten.
7. Bewaar het gereedschap en de accu niet op plaatsen waar de temperatuur kan oplopen tot 50°C of hoger.
8. Werp de accu nooit in het vuur, ook niet wanneer hij zwaar beschadigd of volledig versleten is. De accu kan namelijk ontploffen in het vuur.
9. Wees voorzichtig dat u de accu niet laat vallen en hem niet blootstelt aan schokken of stoten.
BEWAAR DEZE VOORSCHRIFTEN.
Tips voor een maximale levensduur van de accu
1. Laad de accu op voordat hij volledig ontladen is. Stop het gebruik van het gereedschap en laad de accu op telkens wanneer u vaststelt dat het ver­mogen van het gereedschap is afgenomen.
2. Laad een volledig opgeladen accu nooit opnieuw op. Als u de accu te veel oplaadt, zal hij minder lang meegaan.
3. Laad de accu op bij een kamertemperatuur tus­sen 10°C en 40°C. Laat een warme accu afkoelen alvorens hem op te laden.
4. Laad de nikkel-metaalhydride accu op telkens wanneer u hem langer dan zes maanden niet hebt gebruikt.
16
Page 7
AANVULLENDE VEILIGHEIDSVOORSCHRIFTEN VOOR HET GEREEDSCHAP
1. Denk eraan dat dit gereedschap altijd gebruiks­klaar is, omdat het niet op een stopcontact hoeft te worden aangesloten.
2. Houd het gereedschap bij de geïsoleerde hand­grepen vast wanneer u boort op plaatsen waar het gereedschap met verborgen elektrische bedrading in aanraking kan komen. Door contact met een onder spanning staande draad, zullen ook de niet-geïsoleerde metalen delen van het gereedschap onder spanning komen te staan en zal de gebruiker een elektrische schok krijgen.
3. Zorg ervoor dat u altijd stevige steun voor de voeten hebt.
4. Controleer of er zich niemand beneden bevindt wanneer u het gereedschap op een hoge plaats gaat gebruiken.
5. Houd het gereedschap stevig vast.
6. Houd uw handen uit de buurt van roterende onderdelen.
7. Laat het gereedschap niet achter terwijl het nog in bedrijf is. Bedien het gereedschap alleen wan­neer u het met de handen vasthoudt.
8. Raak de boor of het werkstuk niet aan onmiddel­lijk na het gebruik; deze kunnen erg heet zijn en brandwonden veroorzaken.
BEWAAR DEZE VOORSCHRIFTEN.
BEDIENINGSVOORSCHRIFTEN
Installeren of verwijderen van de accu (Fig. 1)
• Schakel het gereedschap altijd uit alvorens de accu te
installeren of te verwijderen.
• Om de accu te verwijderen, neemt u deze uit het
gereedschap terwijl u de knoppen aan beide zijden van de accu indrukt.
• Om de accu te installeren, past u de rug op de accu in
de groef in de behuizing van het gereedschap, en dan schuift u de accu naar binnen. Schuif de accu zo ver mogelijk erin, totdat deze met een klikgeluid vergren­delt. Indien u dit niet doet, kan de accu per ongeluk uit het gereedschap vallen en uzelf of anderen verwon­den.
• Als de accu moeilijk in de houder gaat, moet u niet pro-
beren hem met geweld erin te duwen. Indien de accu er niet gemakkelijk ingaat, betekent dit dat u hem niet op de juiste wijze erin steekt.
Installeren of verwijderen van de schroefbit of boor (Fig. 2)
Belangrijk: Controleer altijd of het gereedschap is uitgeschakeld en de accu is verwijderd alvorens de boor te installeren of te verwijderen.
Houd de ring vast en draai de bus naar links om de klau­wen van de boorkop te openen. Steek de boor zo ver mogelijk in de boorkop. Houd daarna de ring weer stevig vast en draai de bus naar rechts om de boorkop vast te zetten. Om de boor te verwijderen, houdt u de ring vast en draait u de bus naar links.
Werking van de trekschakelaar (Fig. 3)
LET OP: Alvorens de accu in het gereedschap te plaatsen, moet u altijd controleren of de trekschakelaar juist werkt en bij het loslaten naar de “OFF” positie terugkeert.
Om het gereedschap in te schakelen, drukt u gewoon de trekschakelaar in. Hoe dieper de trekschakelaar wordt ingedrukt, hoe sneller het gereedschap draait. Om het gereedschap uit te schakelen, de trekschakelaar losla­ten.
Werking van de omkeerschakelaar (Fig. 4)
LET OP:
• Controleer altijd de draairichting alvorens het gereed­schap te gebruiken.
• Verander de stand van de omkeerschakelaar alleen nadat het gereedschap volledig tot stilstand is geko­men. Indien u de draairichting verandert terwijl de boor nog draait, kan het gereedschap beschadigd raken.
• Zet de omkeerschakelaar altijd in de neutrale stand wanneer u het gereedschap niet gebruikt.
Dit gereedschap heeft een omkeerschakelaar voor het veranderen van de draairichting. Druk de omkeerschake­laar in vanaf zijde A voor rechtse draairichting, of vanaf zijde B voor linkse draairichting. Wanneer deze schake­laar in de neutrale stand staat, kan de trekschakelaar niet worden ingedrukt.
Veranderen van het toerental (Fig. 5)
Om het toerental te veranderen, schakelt u eerst het gereedschap uit en dan schuift u de toerentalschakelaar naar de “II” zijde voor hoog toerental, of naar de “ I” zijde voor laag toerental. Zorg ervoor dat de toerentalschake­laar in de juiste stand staat alvorens met het werk te beginnen. Gebruik het toerental dat geschikt is voor uw werk.
LET OP:
• Schuif de toerentalschakelaar altijd volledig naar de juiste positie. Als u het gereedschap gebruikt met de toerentalschakelaar halverwege tussen de “ I ” en “II” posities, kan het gereedschap beschadigd raken.
• Verschuif de toerentalschakelaar niet terwijl het gereedschap draait. Hierdoor kan het gereedschap beschadigd raken.
Instellen van het draaimoment (Fig. 6)
Het draaimoment kan worden ingesteld in 17 stappen door de stelring zodanig te draaien dat zijn schaalverde­lingen overeenkomen met de wijzer op het huis van het gereedschap. Het draaimoment is minimaal wanneer het cijfer 1 met de wijzer overeenkomt, en is maximaal wan-
A markering met de wijzer overeenkomt.
neer de Wanneer de stelring op een cijfer van 1 tot 16 is inge­steld, zal de koppeling bij verschillende draaimomentni­veaus slippen. De koppeling is ontworpen om niet te slippen bij de werk te beginnen, moet u het geschikte draaimoment bepalen door een proefschroef in uw werkstuk of in een ander stuk van hetzelfde materiaal te schroeven.
OPMERKING: Gebruik het gereedschap niet met de stelring ingesteld tussen het cijfer 16 en de A gereedschap beschadigd raken.
A markering. Alvorens met het eigenlijke
markering. Hierdoor kan het
17
Page 8
Indraaien van schroeven (Fig. 7)
Plaats de punt van de schroefbit in de schroefkop en oefen druk op het gereedschap uit. Begin met lage snel­heid en voer dan de snelheid geleidelijk op. Laat de trek­schakelaar los zodra de koppeling ingrijpt.
OPMERKING:
• Zorg ervoor dat u de schroefbit recht op de schroefkop plaatst, aangezien anders de schroef en/of de schroef­bit beschadigd kan worden.
• Wanneer u houtschroeven indraait, maak dan voor­boorgaten in het hout. Dit vergemakkelijkt het inschroe­ven en voorkomt dat het hout splijt. Zie de onderstaande tabel.
Nominale diameter van
houtschroef (mm)
3,1 2,0 – 2,2
3,5 2,2 – 2,5
3,8 2,5 – 2,8
4,5 2,9 – 3,2
4,8 3,1 – 3,4
5,1 3,3 – 3,6
5,5 3,6 – 3,9
5,8 4,0 – 4,2
6,1 4,2 – 4,4
• Indien het gereedschap ononderbroken wordt gebruikt totdat de accu is ontladen, dient u het gereedschap 15 minuten te laten rusten alvorens met een nieuwe accu verder te werken.
Aanbevolen diameter
van voorboorgat (mm)
Boren
Draai eerst de stelring zodat de wijzer op het gereed­schap naar de werk.
• Boren in hout Voor boren in hout krijgt u de beste resultaten met houtboren die voorzien zijn van een geleideschroef. Het boren gaat dan gemakkelijker aangezien de gelei­deschroef de boor in het hout trekt.
• Boren in metaal Om te voorkomen dat de boor slipt wanneer u begint te boren, moet u van te voren met een drevel een deukje in het metaal slaan op de plaats waar u wilt boren. Plaats vervolgens de boorpunt in het deukje en start het boren. Gebruik altijd boorolie wanneer u in metaal boort. De enige uitzonderingen zijn ijzer en koper die droog geboord dienen te worden.
A markering wijst. Ga dan als volgt te
LET OP:
• Door overmatige druk op het gereedschap uit te oefe­nen verloopt het boren niet sneller. Integendeel, teveel druk op het gereedschap zal alleen maar de boorpunt beschadigen, de prestatie van het gereedschap ver­minderen en de gebruiksduur verkorten.
• Wanneer de boor uit het gaatje tevoorschijn komt, wordt een enorme kracht uitgeoefend op het gereed­schap en op de boor. Houd daarom het gereedschap stevig vast en wees op uw hoede wanneer de boor door het werkstuk begint te dringen.
• Wanneer de boor klemraakt, keert u met de omkeer­schakelaar de draairichting om, om de boor uit het gaatje te krijgen. Het gereedschap kan echter plotse­ling terugspringen indien u het niet stevig vasthoudt.
• Kleine werkstukken dient u altijd eerst vast te zetten in een klemschroef of iets dergelijks.
• Indien het gereedschap ononderbroken wordt gebruikt totdat de accu is ontladen, dient u het gereedschap 15 minuten te laten rusten alvorens met een nieuwe accu verder te werken.
ONDERHOUD
LET OP: Controleer altijd of het gereedschap is uitgeschakeld en de accu is losgekoppeld vooraleer onderhoud uit te voe­ren aan het gereedschap.
Opdat het gereedschap veilig en betrouwbaar blijft, die­nen alle reparaties, onderhoud of afstellingen te worden uitgevoerd bij een erkend Makita service centrum.
ACCESSOIRES
LET OP:
• Deze accessoires of hulpstukken worden aanbevolen voor gebruik met het Makita gereedschap dat in deze gebruiksaanwijzing is beschreven. Bij gebruik van andere accessoires of hulpstukken bestaat er gevaar voor persoonlijke verwonding. Gebruik de accessoires of hulpstukken uitsluitend voor hun bestemde doel.
Raadpleeg het dichtstbijzijnde Makita Servicecentrum voor verder advies of bijzonderheden omtrent deze accessoires.
•Schroefbits
• Rubber steunschijf set
• Schuimrubber polijstkussen 125
• Wollen poetsschijf 100
• Diverse types originele Makita accu’s en acculaders
• Plastic draagkoffer
18
Loading...