Makita 6OLODWK, 6010D, 6010DW, 6010DWK Instruction Manual
Cordless
Drills
-
Capacities
No
load
speed Net weight
Steel
I
Wood Wood screw
10
mm
1318")
600
Rimin.
1.1
kg (2.4 Ibs)
4.5
mm
x
20
mm
(311
6"
x
314")
10
mm
(318")
MODEL 6010D
10
mm
(318")
MODEL 6OlODW
10
mm
(318")
MODEL 6OlODWK
With Fast Charger
With Fast Charger and Carrying Case
Overall length
227
mm
19")
INSTRUCTION MANUAL
Battery Cartridge
7000
Voltage
7.2 V
1
SPEC
I
FI CAT
IO
N
S
*
Model DC7100 Fast Charger
Dimensions Net Charging
IL
x W x
HI
weight time
50
Hz
-
60
Hz
7.2 V
15-314" x 3-118"
x
2-318")
(1
5
lbs)
'
Hr
Input output
A.C
only D.C.
145
mm
x
80
mm
x
61
mm
0.7
kg
IMPORTANT
SAFETY INSTRUCTIONS
(For
All
Tools)
WARNING:
WHEN USING ELECTRIC TOOLS, BASIC SAFE-
TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
SONAL INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER-
1.
2.
3.
4.
5.
6.
7.
8.
9.
IO.
11.
12.
13.
2
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don't use power tools
in
damp
or wet locations. Keep work area well
lit.
Don't expose power tools to rain.
Don't use tool in presence of flammable liquids or gases.
KEEP CHILDREN AWAY. All visitors should be kept away from work area.
Don't let visitors contact tool or extension cord.
STORE IDLE TOOLS. When not
in
use, tools should be stored
in
dry, and high
or locked-up place
-
out of reach of children.
DON'T FORCE TOOL.
It
will
do the job better and safer at the rate for which
it
was intended.
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a
heavy-duty tool. Don't use tool for purpose not intended.
DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught
in
moving parts. Rubber gloves and non-skid footwear are recommended
when working outdoors. Wear protective hair covering to contain long hair.
USE SAFETY GLASSES. Also use face or dust mask
if
cutting operation is
dusty.
DON'T ABUSE CORD. Never carry tool by cord or yank
it
to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It's safer than using
your hand and
it
frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace
if
damaged. Keep handles dry, clean, and free from oil and grease.
DISCONNECT TOOLS. When not in use, before servicing, and when chang-
ing accessories, such as blades, bits, cutters.
14.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are removed from tool before turning
it
on.
15.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool
with
finger
on switch. Be sure switch is OFF when plugging
in.
16.
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and
so
marked.
17.
STAY ALERT. Watch what you are doing, use common sense. Don't operate
tool when you are tired.
18.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that
it
will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere
in
this instruction manual.
Have defective switches replaced by authorized service center. Don't use
tool
if
switch does not turn
it
on and off.
19.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact
with
grounded
surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.
20.
REPLACEMENT PARTS. When servicing, use only identical replacement parts.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
nameplate of the tool. A power source
with
voltage greater than that specified
for the tool can result
in
SERIOUS INJURY to the user - as well as damage to
the tool. If
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source
with
voltage less than the nameplate rating is harmful to the motor.
3
IMPORTANT SAFETY INSTRUCTIONS
Length of Cord (Feet)
AWG Size of Cord
I.
SAVE THESE INSTRUCTIONS
-
This manual
25
50
100 150
18 18
18 16
contains important safety and operating instructions for battery charger.
2.
Before using battery charger, read all instructions and cautionary markings
on
(1)
battery charger,
(2)
battery, and
(3)
product using battery.
3.
CAUTION
-
To reduce risk of injury, charge only MAKITA Battery
7000.
Other types of batteries may burst causing personal injury and damage.
4.
Do not expose charger to rain or snow.
5.
Use of an attachment not recommended or sold by the battery charger
manufacturer may result in a risk of fire, electric shock, or injury to persons.
6.
To
reduce risk of damage to electric plug and cord, pull by plug rather than
cord when disconnecting charger.
7.
Make sure cord is located
so
that
it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
8.
An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins
on
plug of extension cord are the same number, size, and shape
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is at least as large as the one specified in the table below.
TABLE
1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS
FOR
BATTERY CHARGERS
as those of plug on charger;
9.
Do not operate charger with damaged cord or plug
-
replace them im-
mediately.
IO.
Do not operate charger
if
it
has received a sharp blow, been dropped, or other-
wise damaged in any way; take
it
to a qualified serviceman.
11.
Do not disassemble charger or battery cartridge; take
it
to a qualified
serviceman when service or repair is required. Incorrect reassembly may
result in a risk
of
electric shock or fire.
12.
To reduce risk of electric shock, unplug charger from outlet before attempt-
ing any maintenance or cleaning. Turning off controls will not reduce this risk.
4
ADDITIONAL SAFETY RULES
FOR CHARGER
&
BATTERY CARTRIDGE
1.
Do
not charge Battery Cartridge when temperature is BELOW 10°C (5OOF)
2.
Do
not attempt to use a step-up transformer, an engine generator or DC power
3.
Do
not allow anything to cover or clog the charger vents.
4.
Always cover the battery terminals with the battery cover when the battery
5.
Do
not short the battery cartridge:
or ABOVE 4OoC (104OF).
receptacle.
cartridge
is
not used.
(1)
Do
not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such
(3)
Do
not expose battery cartridge to water or rain.
as nails, coins, etc.
A battery short can cause a large current flow, overheating, possible burns
and even a breakdown.
6.
Do
not store the tool and Battery Cartridge in locations where the tempera-
7.
Do
not incinerate the Battery Cartridge even
if
it
is severely damaged or is
ture may reach or exceed 5OoC (122OF).
completely worn out. The battery cartridge can explode in a fire.
ADDITIONAL SAFETY RULES
1.
Be aware that this tool is always in an operating condition, because
it
does
2.
Always be sure you have a firm footing.
3.
Hold the tool firmly.
4.
Keep hands away from rotating parts.
5.
When drilling into walls, floors or wherever "live" electrical wires may be
encountered,
DO
NOT TOUCH ANY METAL PARTS
OF
THE TOOL!
Hold the tool only by the insulated grasping surfaces to prevent electric shock
if
you drill into a "live" wire.
not have to be plugged into an electrical outlet.
Be sure no one is below when using the tool in high locations.
6.
Do
not leave the tool running. Operate the tool only when hand-held.
7.
Do
not touch the drill bit or the workpiece immediately after operation: they
may be extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
5
Loading...