Page 1
Chain
Saw
300
mm
(11-3/4")
MODEL
INSTRUCTION MANUAL
5012B
SPEC
IF1
CAT
I
ON
S
Guide
Chain speed
1FPMl
5,500
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country to country.
length
300
11
1-314")
bar
mm
Saw chain
Pitch Gauge
(9.5
318"
mm)
0.050"
11.27
mm)
Overall
length
560
122")
DOUBLE
INSULATION
mm
weight
4.3
19.5
kg
Ibs)
Page 2
IMPORTANT
SAFETY
WARNING:
WHEN USING AN ELECTRIC CHAIN SAW, BASIC
INSTRUCTIONS
SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY
TO PERSONS, INCLUDING THE FOLLOWING:
READ
1.
2.
3.
4.
5.
6.
7.
8.
2
ALL
Keep Work Area Clean
Cluttered areas invite injuries. Do not start cutting
area, secure footing, and a planned retreat path from the falling tree.
Consider Work Area Environment
Use extreme caution when cutting small size brush and saplings because
the slender material may catch the saw chain and be whipped toward you
or pull you off balance. Do not operate a chain saw
cally trained to do
spring back
fibers is released. Don‘t expose chain saw to rain. Don’t use chain saw in
damp or wet locations. Do not use chain saw
liquids or gases.
Guard Against Electric Shock
Prevent body contact with grounded surfaces. For example: metal pipes, wire
fences.
Keep Children Away
Do not let visitors contact chain saw or extension cord. All visitors should
be kept away from work area.
Store Idle Chain Saw
When not
up place
or carrying case.
Don’t Force Chain Saw
It
will do the job better and safer at the rate for which
Use Right Tool
Cut wood only. Don’t use chain saw for purpose not intended
-
Don’t use chain saw for cutting plastic, masonry non-wood building
materials.
Dress Properly
Do not wear loose clothing or jewelry. They can get caught in moving parts.
Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
INSTRUCTIONS.
until
you have a clear work
in
a tree unless specifi-
so.
When cutting a limb that is under tension be alert for
so
that you will not be struck when the tension in the wood
in
presence of flammable
in
use, chain saws should be stored in a dry, and high or locked-
-
out of the reach of children. When storing saw, use a scabbard
it
was intended.
-
for example
Page 3
9.
Use Safety Glasses
Also
use safety footwear; snug fitting clothing; protective gloves; hearing
and head protection.
Carrying Saw
IO.
Carry the chain saw by the front handle
the switch, the guide bar and saw chain to the rear.
11.
Maintain Chain Saw With Care
Inspect chain saw cords periodically and if damaged, have repaired by
authorized service facility. Keep cord clear of the chain and operator at all
times. Never carry saw by the cord or pull
Keep cord from oil and sharp edges. Inspect extension cords periodically and
replace
mance. Follow instructions for lubricating and changing accessories. Keep
handles dry, clean, and free from oil and grease.
Disconnect Chain Saw
12.
Disconnect chain saw when not
accessories and attachments, such as saw chain and guard.
Outdoor Use Extension Cords
13.
Use only extension cords intended for use outdoors and
14.
Stay Alert
Watch what you are doing. Use common sense.
when you are tired. Keep all parts of the body away from the saw chain when
the motor is operating. Before you start the saw, make sure the saw chain
is not contacting anything.
Check Damaged Parts
15.
Before further use of the chain saw, a guard or other part that is damaged
should be carefully checked to determine that
perform its intended function. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center unless other-
wise indicated elsewhere
replaced by authorized service center.
not turn
adjusted, or is not completely and securely assembled. Be sure that the saw
chain stops moving when the trigger is released.
Guard Against Kickback
16.
WARNING: KICKBACK may occur when the nose or tip of the guide bar
touches an object, or when the wood closes
in
reaction, kicking the guide bar up and back towards the operator. Pinching
the saw chain along the top of the guide bar may push the guide bar rapidly
back towards the operator. Either of these reactions may cause you to lose
control of the saw which could result
precautions should be followed to minimize kickback.
if
damaged. Keep tools sharp and clean for better and safer perfor-
it
on and off.
the cut. Tip contact
Do
in
use. before servicing, and when changing
in
this instruction manual. Have defective switches
not operate a chain saw that is damaged, improperly
in
some cases may cause a lightning fast reverse
with
the saw stopped, finger off
it
to disconnect from receptacle.
so
marked.
Do
not operate chain saw
it
will operate properly and
Do
not use chain saw if switch does
in
and pinches the saw chain
in
serious injury to user. The following
3
Page 4
(1)
Grip saw firmly. Hold the chain saw firmly with both hands when the
motor is running. Use a firm grip with thumbs and fingers encircling the
chain saw handles.
(2)
Do not over reach.
(3)
Keep proper footing and balance at all times.
(4)
Don't let the nose of the guide bar contact a log, branch, ground, or other
obstruction.
(5)
Don't cut above shoulder height.
(6)
Use devices such as low kickback chain and special guide bars that
reduce the risks associated with kickback.
(7)
Only use replacement bars and chains specified by the manufacturer.
17.
Power Supply
Connect chain saw to correct voltage, that is, be sure that the voltage
supplied is the same as that specified on the nameplate of the tool.
18.
Replacement Parts
When servicing use only identical replacement parts.
19.
Wear ear protectors during operation.
20.
Before making a felling cut, remove dirt, stones, loose bark, nails, staples
and wire from the tree.
21.
Secure the log
22.
AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool
on switch. Be sure switch is
23.
Attention! Do not expose this tool to rain and pull plug immediately if the
supply cable be damaged or cut.
24.
The chain saw must not be left outdoors during rain and
when wet.
so
that
it
will not roll or move suddenly during operation.
with
OFF
when plugging in.
it
must not be used
finger
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle,
outlet, etc.) be sure the voltage supplied is the same as that specified on the
A
nameplate of the tool.
for the tool can result
the tool.
voltage less than the nameplate rating is harmful to the motor.
4
If
in
doubt, DO NOT PLUG IN THE TOOL. Using a power source with
power source with voltage greater than that specified
in
SERIOUS INJURY to the user - as well as damage to
Page 5
Use Of Extension Cord
If
the extension cord is intended to be used outdoors, the cord shall be marked
with the suffix
to indicate
A.
W-A
following the cord type designation, for example
it
is acceptable for outdoor use. Use an extension cord heavy
-
SJTW-
enough to carry the current the tool will draw. Undersize cord will cause a drop
in line voltage resulting in
loss
of power and over-heating. Make sure the extension cord is in good condition before using. Keep the cord away from the cutting area and
to
position cord
so
that
it
will not be caught on branches, and the
like, during cutting. Use the table below to determine the proper wire size required in the extension cord.
Ampere rating
(on nameplate)
I
Ext. Cord Length
25
Ft.
50
Ft.
75
Ft.
100
Ft.
125
Ft.
150
Ft.
0 - 5.0 5.1 - 10.0 10.1 - 13.0 13.1 - 15.0
I
18 18 16 14
18 16 16 14
18 16 14 14
16 14 12 12
16 12 12 12
16 12 12
Wire Size (American Wire Gauge)
-
Contact Makita Authorized or Factory Service Center if a proper extension cord
cannot be found.
SAVE
THESE INSTRUCTIONS.
5
Page 6
LEFT SIDE
Chain Saw Nomenclature
Front handle Manual oiler control
I
Trigger switch
SIDE
Oil
cap Guide bar nose
Sprocket mounting pad
Guide bar
Fig.
Bucking - The process of cross cutting a felled tree or log into lengths.
-
A
Chain Saw Powerhead
-
Sprocket
Felling
Felling Back Cut
The toothed part that drives the saw chain.
-
The process of cutting down a tree.
-
The final cut
chain saw without the saw chain and guide bar.
in
a tree felling operation made on the opposite
side of the tree from the notching undercut.
-
Front Handle
Front Handle Guard
The support handle located at the front of the chain saw.
-
A
structural barrier between the front handle of a chain
saw and the guide bar, typically located close to the hand position on the front
handle.
Guide Bar
-
A
solid railed structure that supports and guides the saw chain.
1
6
Page 7
Kickback - The backward or upward motion, or both
when the saw chain near the nose of the top area of the guide bar contacts any
object such as a log or branch, or when the wood closes in and pinches the saw
chain in the cut.
-
Kickback, Pinch
wood closes
the guide bar.
Kickback, Rotational
can occur when the moving saw chain near the upper portion of the tip of the
guide bar contacts an object, such as a log or branch.
Low-Kickback Chain
requirements of
saws.
Normal Cutting Position
and felling cuts.
Notching Undercut
Oiler Control
Rear Handle
Reduced Kickback Guide Bar
reduce kickback significantly.
Replacement Saw Chain
requirements of ANSI 8175.1 when tested
meet the
Saw Chain
is driven by the motor and is supported by the guide bar.
Spiked Bumper (Spike)
bucking to pivot the saw and maintain position while sawing.
Switch
power circuit to the motor of the chain saw.
Lock-Off Button
the switch until manually actuated.
ANSI
-
-
A
device that when operated will complete or interrupt an electrical
The rapid pushback of the saw which can occur when the
in
and pinches the moving saw chain in the cut along the top of
-
The rapid upward and backward motion of the saw which
-
A
chain that complies with the kickback performance
ANSI
B175.1 when tested on a representative sample of chain
-
Those positions assumed in performing the bucking
-
A
notch cut in a tree that directs the tree's fall.
-
A
system for oiling the guide bar and saw chain.
-
The support handle located at the rear of the saw.
-
A
guide bar which has been demonstrated to
-
A
chain that complies with the kickback performance
with
performance requirements when used with other saws.
A
loop of chain having cutting teeth, that cut the wood, and that
-
The pointed tooth or teeth for use when felling or
-
A movable stop that prevents the unintentional operation of
of
the
guide bar
specific chain saws.
occurring
It
may not
7
Page 8
Installing saw chain and guide
CAUTION
:
Always be sure that the tool
bar
is
switched off and unplugged before installing saw chain and
guide bar.
Use the socket wrench to toosen the hex
bolt holding the chain cover. Remove the
chain cover.
Fig.
Fit one end of the chain over the sprocket and the other over the end of the guide bar.
Notice that the cutters must be in the direction of the arrow in Fig.
3
and
4.
Keep the
chain in the guide bar grooves.
I
2
Install the guide bar
that the lower hole in the guide bar
is
just over the adjusting pin.
so
Install the chain cover and tighten the hex bolt only tight enough to hold the guide bar
temporarily.
Adjusting saw chain tension
CAUTION
Always be sure that the tool
:
is
switched off and unplugged before adjusting chain tension.
Grasp the chain in the middle of the guide
bar and lift up. The gap between the side
link of the chain and the guide bar should
be about
8
3
mm to 4 mm
(1/8”
-
5/32”).
Fig.
5
Page 9
If the gap
is
not about
3
mm
to 4 mm
(1/8" - 5/32"), adjust the chain tension.
a
screwdriver to turn the chain tension
Use
adjusting screw clockwise for more tension,
or counterclockwise for less tension. When
adjusting the chain tension, lift the end
the guide bar slightly.
of
I
After adjusting the chain tension, use the
socket wrench to tighten the hex bolt
sew
re1
y
.
1
CAUTION
:
When breaking in a new chain, adjust the tension often, since it tends
Hook
When using an extension cord, secure it
the tool's cord with the hook provided.
Attach the hook about 100-200 mm
8")
from the extension cord connector.
to
(4"-
I
1
Cord connector
This will help prevent unintentional dis-
connection.
to
'stretch'.
Power cord
I
Fig.
6
I
I
Fig.
7
I
I
Extension cord
I
Fig.
8
9
Page 10
Switch action
To prevent the trigger from being acciden-
tally pulled,
as
a
safety feature.
lock-off button
is
provided
a
To start the tool, press in the lock-off
button and pull the trigger.
Release
the
trigger to stop.
CAUTION:
Before plugging in the tool, always check to
see
and returns to the "OFF" position when released.
Trigger
I
switch
Fig.
that the trigger switch actuates properly
Lubrication
I
Turn the tool on and then depress the oil
button
or 5 times. Let the oil
get
around
4
the bar groove and penetrate before cutting. For continuous operation, lubricate
a
the tool for every log having
about 200"
4
button
or 5 times. For greater thickness,
(8')
by depressing the
depress the button several times
diameter of
at
some
point in the cutting.
Insufficient oiling will cause wear on the rivets, rough chain travel and high chain tension.
a
Use in such conditions will put
cut out. Unplug the saw and pump the oil plunger
great load on the motor, and the overload protector may
5
or 6 times while running the saw
chain around by hand. After enough lubrication, resume sawing operations.
I
10
Fig.
11
Page 11
To replenish the oil, take
off
the cap on
the tank and fill with the oil supply.
CAUTION
Turbine oil
is
neither needed nor advisable, since the aim
Do
Cutting operation
:
#200
or machine
oil
not use dirty oil nor volatile oil.
is
recommended. A special
is
to lubricate the chain and the guide bar.
oil
or one of high viscosity
Turn the tool on and allow the chain to reach full speed before
is
Be sure the chain
Use the spike
tool into the wood, rocking
Do
not force the guide bar in. Whenever
heavy work
adequately lubricated.
as
a
pivot point and
is
prolonged, the overload pro-
ease
it
in gently.
the
tector will cut out to stop the motor.
it
contacts the wood.
Fig.
12
CAUTION
If you notice that the guide bar
:
is
too hot to touch, stop operation and
off. Check the chain tension. Make sure the oil
Overload protector
The overload protector automatically cuts
out to break the circuit and the button
pops out, whenever heavy work
is
pro-
longed. If this occurs, turn the switch off
and unplug the tool. Check the chain tension,
oil
feeding and your sawing method.
Then press the restart button to resume
operation. Your finger should not be on
the trigger when you press the restart
button, however.
is
feeding properly.
let
the tool cool
Fig.
14
11
Page 12
Holding the chain saw
Always grip each handle with the thumb
as
and fingers encircling the handle
in
Fig.
15.
shown
I
Use
this
thumb
grip
below
I
Fig.
l!
Using the chain saw
Always be sure of your footing and hold the chain saw firmly with both hands while the
motor
is
running.
a
Felling
When bucking and felling operations are being performed by two or more persons,
tree
at
the
same time, the felling operation should be separated from the bucking operation by
distance of
a
manner that would endanger any person, strike any utility line or cause any property
at
least
twice the height of the tree being felled. Trees should not be felled in
damage. If the tree does make contact with any utility line, the utility company should
be notified immediately.
The chain saw operator should keep on the uphill side of the terrain
it
is
to roll or slide downhill after
felled.
as
the tree
is
likely
A retreat path should be planned and
as
cleared
The retreat path should extend back and
necessary before cuts are started.
\Retreat
diagonally to the rear of the expected line
of fall
as
shown in Fig.
Before felling
is
16.
Fig.
started, consider the natural lean of the tree, the location of larger
branches and the wind direction to judge which way the tree will fall. Remove dirt, stones,
loose bark, nails, staples, and wire from the tree where felling cuts are to be made.
a
1,
12
Page 13
Notching undercut
Make the notch
shown in Fig.
?/3
the diameter of the
17.
Make the lower horizontal notching cut first. This will help to avoid
tree,
perpendicular to the direction
pinching of either the saw chain or the guide bar when the second notch
Felling back cut
Make the felling back cut
(50.8
mm) higher than the horizontal
notching cut
as
shown in Fig.
at
least
17.
2
inches
Keep the
felling back cut parallel to the horizontal
notching cut. Make the felling back cut
enough wood
is
left to act
as
a
hinge. The
so
hinge wood keeps the tree from twisting
Do
and falling in the wrong direction.
not
cut through the hinge.
is
being made.
of
fall
as
I
Fig.
1
As
the felling cut gets close to the hinge the tree should begin to fall. If there
chance that the tree may not fall in the desired direction or
the saw chain, stop cutting before the felling back cut
it
may rock back and bind
is
complete and use wedges of
wood, plastic or aluminum to open the cut and drop the tree along the desired line of fall.
When the tree begins to fall remove the chain saw from the cut, stop the motor, put the
chain saw down, then use the retreat path planned. Be alert for overhead limbs falling and
watch your footing.
Limbing
Limbing
fallen tree. When limbing,
a
tree
is
removing the branches from
leave
larger
a
LIMB
CUT
Keep work
Leave support
off
ground
limbs
until log
is
cut
lower limbs to support the log off the
ground. Remove the small limbs in one
cut
as
shown in Fig.
18.
Branches under
tension should be cut from the bottom up
to avoid binding the chain saw.
is
Fig.
any
18
13
Page 14
Bucking
Bucking
your weight
a
log
is
cutting a log into lengths.
is
evenly distributed on both feet. When possible, the log should be raised
It
is
improtant to make sure your footing
and supported by the use of limbs, logs or chocks.
cutting.
Follow
the simple directions for easy
is
firm and
When the log
is
supported on one end,
as
shown in Fig. 20, cut 1/3 the diameter
from the underside (underbuck). Then
make the finished cut by overbucking to
meet the first cut.
When the log
shown in
is
supported on both ends,
Fig.
21, cut 1/3 of that diameter
as
from the top overbuck. Then make the
finished cut by underbucking the lower
2/3 to meet the first cut.
2nd Cut overbuck
(2/3diameter)
to meet 1st cut
(to avoid pinching)
~~)~~~~~$~Ck
(to
avoid splintering)
2nd
cut underbuck
(2/3 diameter) to
meet 1st cut
(to avoid pinching)
14
Page 15
When bucking on a slope, always stand on
as
the uphill side of the log,
22.
When "cutting through", to maintain
shown in
Fig.
complete control, release the cutting pressure near the end of the cut without re-
laxing your grip on the chain saw handles.
Don't
let
the chain contact the ground.
After completing the cut, wait for the
saw
chain
to
stop
before
you move the
chain saw. Always stop the motor before
moving from tree to tree.
Carrying
tool
Carry the tool by the front handle with the
tool turned off, finger off the switch, the
guide bar and the saw chain to the rear.
Use the scabbard to cover the guide bar
and the saw chain.
Fig.
2
Fig.
2:
Page 16
MA1 NTENANCE
CAUTION
Always be sure that the tool
inspection or maintenance.
Filling saw chain
To
and filed properly
To file the saw chain, push the file in the
direction of the arrow. When pulling
back, be careful not to touch the cutters
with the file.
:
is
switched off and unplugged before attempting to perform
get the most in cutting performance from your tool, you must keep the cutters sharp
as
shown below.
TOP PLATE ANGLE SIDE PLATE ANGLE TOP FILING ANGLE
Raker
A
30'
top
plate angle
IS
ideal
of
Cutter
File
the side plate
85'.
to
,
If
you have filed the
and side plate correctly
to
the
be
60
8
filling angle
-automatically.
will
it
top
Fig.
2
Fig.
25
After a saw chain has been filed
to be filed down slightly. This
two
or three times, the "raker"
is
because the raker
acts
(see
Fig.
24)
as
a
depth gauge for the cutters.
may need
As the cutters are filed, they lose some height due to their angled shape. Eventually, the
cutters will become lower than the depth gauge and consequently, will not be able to
cut.
To
remedy this, use a flat file to file the tops of the rakers
0.5
mm
(0.025")
below the tips of the cutters
(see
Fig.
24).
rakers excessively or the cutters will be allowed to take too large of
stall
the tool to
16
or snag in the cut.
so
that they are about
Be
careful not to file the
a
"bite", causing
Page 17
Removing chip buildup
Chips and sawdust will build up in the guide bar groove and oil hole, clogging them and
impairing oil flow. Remove the guide bar and clean them out.
Fig.
26
Replacing carbon brushes
Remove and check the carbon brushes
regularly. Replace when they wear down
to the limit mark. Keep the carbon brushes
clean and free to slip in the holders. Both
carbon brushes should be replaced
same time. Use only Makita carbon brushes.
Use
a
screwdriver to remove the brush
holder caps. Take out the worn carbon
brushes, insert the new ones and secure the
brush holder caps.
at
the
I
Guide
bar
-
1
Clean
Id
out
Limit
mark
Fig.
Fig.
I
27
2s
Storing
Before storing the tool, be sure to do the following:
0
0
*Cover the saw chain and the guide bar with the scabbard.
To
adjustment should
always using Makita replacement parts.
the
tool
Remove the chain cover. Remove any chips and sawdust from the tool.
Install the chain cover. Turn the tool on and depress the oil button 4 or 5 times.
maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
be performed by Makita Authorized or Factory Service Centers,
Fig.
29
17
Page 18
ACCESSORIES
CAUTION
These accessories or attachments are recommended for
manual. The
accessories or attachments should
0
Socket wrench
Part
0
Scabbard
Part
0
Saw chain
Part
:
use
of
any other accessories or attachments might present a risk
13
No.
782212-4 Part
No.
41 1936-2
No.
713010-5
be
used only in the proper and intended manner.
Screwdriver
No.
783002-8 Part
0
Oil supply
No.
No.
181 11 7-9
158024-1
Part
0
Hook
Part
use
with your Makita tool specified in this
0
File
of
injury to persons. The
No.
744003-1
Cap for oil supply
Part
No.
24201 2-9
18
Page 19
300
mm
CHAIN
Model
(11-3/4")
SAW
5012B
July-29-'88
EN
Note: The switch, noise suppressor and other part configuratlons
may differ from country
to
country.
19
Page 20
July-29’88
ITEM
r
MACHINE
11
21
31
41
61
71
81
91
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Note The switch and other part specifications
DESCRIPTION
Guide
Chain Cover
Hex Flange Head
Hex Lock Nu1 Me- 13
Flat Washer
Sprocket
Flat Washer 12
Adlust Pin
1
Flat
Head
1
Pan Head
1
Plunger
0
Ring
1
1
Compression Spring
1
Flat Washer 5
1
Caring Complete
1
011
Vessel
1
cap
1
Tube
3
1
Rubber
1
Baffle Plate
1
FIELD
2
Hex
8011 M5x65 (With Washer)
1
Ball
Bearing
1
ln~ulstian
1
ARMATURE ASSEMBLY
IWnh Item 24
Bar
8
6
Screw
Screw
6
Pin
6
ASSEMBLY
6200L8
Washer
Bolt
Max17
M5x25
M5x40 (With Washer)
6
-
281
may
differ from country
MACHINE
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
to
country.
$&
DESCRIPTION
1
Fan 90
1
1
1
1
4
1
2
1
2
1
1
1
1
3
1
1
2
1
3
2
2
1
1
1
6202LL8
Ball Bearing
Rubber
Pin
6
Overload
Protector
Motor Housing Cover
Pan Head
Screw
Switch
Rivet
0-5
Name Plate
Pan
Head
Screw
Strain
Relief
Cord
Cord Guard
Motor Housing
Pan
Head Screw M5x50 IWith Washerl
Pan Head
Screw
PrOfeCmr
Pan Head
Screw
Side
Grip
Pan
Head
Screw
Carbon Brush
Brush
Holder
Pan Head Screw M4x12 IWith Washerl
Pan Head
Relay
Cap
Screw M4x8 IWith Washer)
Cover
-
M4x28 IWith Washer)
M4xl8 IWith Washed
M5x40 IWith Washerl
M5x20 IWith Washer)
M5x30 IWith Washer)
US
MAKITA
Every Makita tool is thorou ly inspected and tested before leaving the factory. It
be free of defects from worf!h&p and materials for the period
original purchase. Should any trouble develop during this oneyear period, retum the COMPLETE
tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows
the trouble is caused by defective workmanship or material, Makita
replace) without charge.
This
Warranty does not apply where:
repain have been made or attempted by others:
repairs are required because of normal wear and tear:
The tool has been abused, misused or improperly maintained;
alterations have been made to the
IN NO EVENT SHALL MAKlTA BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CONSEQUENTIAL
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKlTA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED
WARRANTIES
AFTER
This
state
damages, so the above limitation or exclusion may not apply to you. Some states
limitation
DAMAGES
OF
THE
ONE-YEAR TERM OF THIS WARRANTY.
Warranty gives you specific legal rights, and you may also have other rights which vary from
to
state. Some states do not allow the exclusion or limitation of incidental or consequential
on
how long an implied warranty
LIMm
ONE
Warranty
YEAR
Policy
WARRANTY
of
tool.
FROM THE
SALE
OR
USE
OF
THE
PROD^.
“MERCHANTABILITY” AND “FITNESS FOR
lasts,
so
the above limitation may not apply to you.
is
(or
at our option,
THIS
DISCLAIMER
do
warranted
not
allow
ONE YEAR from the date
will
repair
A‘
SPECIFIC PURPOSE,”
to
of
Makita Corporation
3-11-8,
Sumiyoshi-cho,
446
Anjo, Aichi
Japan
8832368066 PRINTED
1991
IN
-
JAPAN
11 - N
Loading...