ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Cleaner
4076D
IMPORTANT: Read Before Using.
008901
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model 4076D
Capacity
Continuous use
Overall length 446 mm (without nozzle) / 983mm (with nozzle)
Net weight 1.1 kg
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Rated voltage D.C. 7.2 V
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
Cd
･ Only for EU countries
Ni-MH
Li-ion
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
Intended use
The tool is intended for collecting dry dust.
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING THIS
APPLIANCE.
High Approx. 10 min.
Low Approx. 20 min.
END004-4
WARNING - To reduce the risk of fire, electric shock
or injury:
1. Do not expose to rain. Store indoors.
2. Do not allow to be used as a toy. Close
attention is necessary when used by or near
children.
3. Use only as described in this manual. Use only
manufacturer's recommended attachments.
4. Do not use with damaged battery. If appliance
is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water,
return it to a service center.
5. Do not handle appliance with wet hands.
6. Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce
air flow.
7. Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving
parts.
8. Turn off all controls before removing the
ENE017-1
battery.
9. Use extra care when cleaning on stairs.
ENA005-3
10. Do not use to pick up flammable or
combustible liquids, such as gasoline, or use
in areas where they may be present.
11. Use only the charger supplied by the
manufacturer to recharge.
12. Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or hot
ashes.
13. Do not use without filters in place.
14. Do not charge the battery outdoors.
15. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
500 ml (for dust bag)
330 ml (for paper pack)
2
responsible for their safety.
16. Children should be supervised to ensure that
they do not play with the appliance.
SAVE THESE INSTRUCTIONS.
This appliance is intended for household use.
ENB106-2
ADDITIONAL SAFETY RULES
1. Read this instruction manual and the charger
instruction manual carefully before use.
2. Do not pick up the following materials:
− Hot materials such as lit cigarettes or
spark/metal dust generated by
grinding/cutting metal
− Flammable materials such as gasoline,
thinner, benzine, kerosene or paint
− Explosive materials like nitroglycerin
− Ignitible materials such as Aluminum, zinc,
magnesium, titanium, phosphorus or
celluloid
− Wet dirt, water, oil or the like
− Hard pieces with sharp edges, such as
wood chips, metals, stones, glasses, nails,
pins or razors
− Powder to clot such as cement or tonor
− Conductive dust such as metal or carbon
− Fine particle like concrete dust
Such action may cause fire, injury and/or
property damage.
3. Stop operation immediately if you notice
anything abnormal.
4. If you drop or strike the cleaner, check it
carefully for cracks or damage before
operation.
5. Do not charge the cleaner close to dangerous
flammable materials such as gasoline, gas,
paint or adhesives.
6. Do not charge the cleaner on papers, cloth,
carpet, vinyl, etc. This may cause a fire.
7. Do not charge the cleaner in a dusty place.
8. Be sure no one is below when using the
cleaner in high locations.
9. Do not bring close to stoves or other heat
sources.
10. Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BUILT-IN BATTERY
1. Before using built-in battery, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble built-in battery.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5. Do not short the built-in battery:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing built-in battery in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose built-in battery to water or
rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
6. Do not store the tool and built-in battery in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).
7. Do not incinerate the built-in battery even if it
is severely damaged or is completely worn out.
The built-in battery can explode in a fire.
8. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the built-in battery before completely
discharged.
Always stop tool operation and charge the
built-in battery when you notice less tool
power.
2. Never recharge a fully charged built-in battery.
Overcharging shortens the battery service life.
3. Charge the built-in battery with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot built-in battery cool down before
charging it.
3
ENC008-1
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off before
adjusting or checking function on the tool.
Charging the built-in battery
1
2
008909
008910
Use only the Makita charger DC7021 to charge this
cleaner. Use of other type chargers may cause the
battery to burst, resulting in personal injury and damage.
Charge the cleaner when it is to be used for the first time
or it has been left uncharged for a long time. Connect
the charging plug to the charging connector, then plug in
the charger to the power receptacle. The light in front of
the cleaner switch will come on and charging will begin.
Charging takes approximately 3 - 5 hours. The light goes
out after the charging is complete. Refer to the
instruction manual for the charger for more details.
CAUTION:
• Do not operate the cleaner during charging. It may
be damaged.
• Always disconnect the charging plug from the
cleaner after charging.
• When you charge a new cleaner or a cleaner
which has been left uncharged for a long time, it
may not accept a full charge. This is a normal
condition and does not indicate a problem. You can
recharge the cleaner fully after discharging it
completely a couple of times.
• Maximum charging time may be 9 hours
depending on room temperature.
1. Charging
connector
2. Charging plug
1. Lamp
1
Switch action
1. Switch
1
008911
CAUTION:
• Always be sure that the dust bag or paper pack is
installed properly in the cleaner before use.
Improper installation may allow dust to enter the
motor, resulting in malfunction of the cleaner.
• Always switch off the cleaner after each use to
prevent damage to the cleaner and to lengthen the
service life of the batteries.
This cleaner can be operated in "standard" and "strong"
suction. For standard suction, slide the switch forward to
the LOW position. For strong suction, slide the switch
further to the HIGH position.
To stop the cleaner, slide the switch back to the OFF
position.
ASSEMBLY
Dust disposal
CAUTION:
• Empty the cleaner before it becomes too full, or the
suction force weakens.
• Be sure to empty out the dust inside the cleaner
itself. Failure to do so may cause the sponge filter
to be clogged or the motor to be damaged.
• Never throw away the dust stopper because it
should be used whenever either the dust bag or
the dust pack is used.
1. Lever
4
008917
1
A
B
008918
Push the A part of the lever and grab it. Pull the lever in
the direction B to open the cover.
C
009692
CAUTION:
• Do not pull the lever in the direction C with
excessive force. Doing this may cause the lever to
be taken apart or damaged.
1
008919
Pull out both the dust stopper and dust bag together at
the same time.
1
1. Dust stopper
1. Dust stopper
008921
Remove the dust stopper and empty the cleaner.
Dust bag and paper pack
Install either dust bag or paper pack before using
cleaner.
Use the dust stopper when installing either dust bag or
paper pack.
Dust bag are usable many times repeatedly by cleaning
it out.
Paper pack is a throw-away type. Throw away the entire
paper pack without emptying when it has become full.
Installing dust bag
1
2
008930
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
1
2
1. Upper side of
dust stopper
2. Lower side of
dust stopper
1. Dust stopper
2. Groove
3
3. Dust bag
008920
008935
1. Insert the protrusion of the dust bag into the
groove in the dust stopper as shown in the figure.
5
1. Lower groove
1
2
1
1. Hook of front
cover
2. Front lip
3. Hook
1
008932
2. There is no distinction between the upper and
lower sides of the dust bag. You may insert its
protrusion of any side into the lower groove of the
dust stopper.
008933
3. Overlap the frame of dust stopper with that of the
dust bag.
1
008929
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way
into the slots in the cleaner cavity.
1. Cleaner cavity
3
008923
6. Hook the front cover onto the front lip of the
2
cleaner. Then close the front cover.
Installing the paper pack
008928
1. Unfold the entrance of the paper pack before
setting it on the dust stopper.
1
2
008930
Use the dust stopper also when installing dust pack. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
1
1. Upper side of
dust stopper
2. Lower side of
dust stopper
1. Dust stopper
2. Dust pack
2
3. Groove
008927
5. Place the entire cloth part of the dust bag inside
the tool itself.
3
008931
2. Insert the protrusion of the dust pack into the
groove in the dust stopper as shown in the figure.
6
1. Lower groove
1
008932
3. There is no distinction between the upper and
lower sides of the dust pack. You may insert its
protrusion of any side into the lower groove of the
dust stopper.
008933
4. Overlap the frame of dust stopper with that of the
dust pack.
1. Cleaner cavity
1
008929
5. Place the dust stopper and the dust pack together
into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way
into the slots in the cleaner cavity.
NOTE:
• The paper pack is a throw-away type. When it has
become full, throw away the entire paper pack
without emptying.
1. Hook of front
cover
2. Front lip
3. Hook
008923
1
2
1
3
2
7. Hook the front cover onto the front lip of the
cleaner. Then close the front cover.
CAUTION:
• Forgetting to install the dust bag or the dust pack,
failure to insert the dust stopper together with the
dust bag or the dust pack all the way into the slots
or using a broken or ripped bag, may allow dust to
get into the motor. This may result in motor failure.
• Do not fold the cardboard at its opening when
installing the paper pack, .
• Never throw away the dust stopper because it
need to be used repeatedly whenever either the
dust bag or the dust pack is used.
OPERATION
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture, etc.
Nozzle slips on easily.
1
1. Nozzle
008927
6. Place the entire container part of the dust pack
inside the tool itself.
7
008913
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for
cleaning a floor while standing erect.
1
1. Cleaner
2. Nozzle
3. Extension wand
After use
2
3
008914
Corner nozzle
Fit on the corner nozzle for cleaning corners and
crevices of a car or furniture.
2
008915
Corner nozzle +Extension wand (Straight pipe)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
1
008916
2
3
1. Cleaner
2. Corner nozzle
1
1. Cleaner
2. Corner nozzle
3. Extension wand
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
008922
When charging or storing the cleaner, hang it from a nail
using the convenient hanger in back by raising it.
Cleaning
008908
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/dust pack
mounting area and the dust stopper.
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may
result.
008934
Wash the dust bag in soapy water when it is clogged
with dust and the cleaner power becomes small. Dry it
out thoroughly before use. An insufficiently dried bag
may cause poor suction and shorten the service life of
the motor.
8
NOTE:
• Dust pack is a throw-away type.
When the sponge filter is clogged with dust, remove it
from the cleaner and then wipe it off or wash in water.
Removing and installing the sponge filter
1
008907
1. Sponge filter
To remove the sponge filter, remove the dust bag or dust
pack and then pinch and take it out.
Removing built-in battery
CAUTION:
• Never remove the built-in battery from the cleaner
except when disposing of the cleaner. The battery
will be damaged or a battery short-circuit could
result.
• Do not touch the terminals with any conductive
material.
• Avoid storing battery unit in a container with other
metal objects such as nails, coins, etc.
• Do not expose battery unit to water or rain.
• Do not disassemble or alter battery unit.
1. Rear cover
008902
1. Wall
1
008906
Press in the whole edge of the sponge filter against the
recessed wall inside the dust bag/dust pack mounting
area.
CAUTION:
• After cleaning sponge filter, be sure to install it on
the cleaner. If washed in water, dry it up before
installing. An insufficiently dried sponge filter may
shorten the service life of the motor.
Disposing cleaner
A Ni-Cd battery is built into this cleaner. Always remove
it before disposing of the cleaner.
1
008905
1. To remove the rear cover, push it in the direction
of the arrow.
1. Battery unit
1
008904
2. Withdraw the built-in battery halfway.
1
008903
1. Connector
3. Disconnect the three lead wires from the battery
by pressing the connector on the part 1 in the
direction of arrow shown in the figure and pulling
them. Then withdraw the battery unit completely.
4. Put the removed battery unit in a plastic bag so
that it is not circuit-shorted.
9
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Extension wand (Straight pipe)
• Nozzle
• Corner nozzle
• Dust bag
• Paper pack
• Dust stopper
• Charger DC7021
10
11 12
884808B8
Makita Corporation
www.makita.com
Loading...