Makita 4014NV, 4014N User Manual

Blower

4014N
4014NV

DOUBLE
INSULATION

SPECIFICATIONS

Model 4014N 4014NV

Capacities

Air pressure (water column)...................................................... 560 mm 0 – 560 mm

Air volume ................................................................................ 2.8 m

No load speed (min

–1

) ................................................................ 16,000 0 – 16,000

Overall length .............................................................................. 430 mm 430 mm

Net weight ................................................................................... 1.75 kg 1.75 kg

• Due to our continuing programme of research and development, the specifications herein are subject to change with-

out notice.

• Note: Specifications may differ from country to countr y.

Power s up ply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can,
therefore, also be used from sockets without earth wire.

3

/min. 0 – 2.8 m3/min.

For European countries only

Noise and Vibration of Model 4014N

The typical A-weighted noise levels are

sound pressure level: 87 dB (A)

ENG005-2-V3

sound power level: 98 dB (A)
Uncertainty is 3 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to

2

.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product
is in compliance with the following standards of standard­ized documents,

EN60745, EN55014, EN61000
in accordance with Council Directives, 73/23/EEC,
89/336/EEC and 98/37/EC.

Yasuhiko Kanzaki

CE 2005

EN60745.

For European countries only

Noise and Vibration of Model 4014NV

The typical A-weighted noise levels are

sound pressure level: 86 dB (A)
sound power level: 97 dB (A)
Uncertainty is 3 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.

Symbols

The followings show the symbols used for the tool. Be sure that you understand their meaning before use.

Read instruction manual.

❏

DOUBLE INSULATION

❏

2

.

ENG005-2-V3

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND

Only for EU countries

Do not dispose of electric equipment together with household waste material!

In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and
its implementation in accordance with national law, electric equipment that have reached the end of
their life must be collected separately and returned to an environmentally compatible recycling facil­ity.

ENH101-4

2

2

2

1

4

3

1

12

6

5

7

34

6

8

7

9

10

11

56

12

13

7

3

ENGLISH

1 Nozzle
2 Blower outlet
3 Suction inlet
4 Dust bag
5 Fastener

Explanation of general view

6 Switch trigger
7 Lock button
8 Speed control screw
9Lower
10 Higher

11 Limit mark
12 Screwdriver
13 Brush holder cap

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all

instructions listed below may result in electric shock, fire
and/or serious injur y. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.

GEA001-3

SAVE THESE INSTRUCTIONS.

Work area safety

1. Keep work area clean and well lit. Cluttered and

dark areas invite accidents.

2. Do not operate power tools in explosive atmo­spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while oper­ating a power tool. Distractions can cause you to

lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet condi­tions. Water entering a power tool will increase the

risk of electric shock.

7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of
electric shock.

Personal safety

9. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools
may result in serious personal injury.

10. Use safety equipment. Always wear eye protec­tion. Safety equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal inju­ries.

11. Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying

power tools with your finger on the switch or plug­ging in power tools that have the switch on invites
accidents.

12. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may
result in personal injury.

13. Do not overreach. Keep proper footing and bal­ance at all times. This enables better control of the

power tool in unexpected situations.

14. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery

or long hair can be caught in moving parts.

15. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of

these devices can reduce dust-related hazards.

Power tool use and care

16. Do not force the power tool. Use the correct
power tool for your application. The correct power

tool will do the job better and safer at the rate for
which it was designed.

17. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be
repaired.

18. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool
accidentally.

19. Store idle power tools out of the reach of chil­dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the

hands of untrained users.

20. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by

poorly maintained power tools.

21. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

22. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and in
the manner intended for the particular type of
power tool, taking into account the working con­ditions and the work to be performed. Use of the

power tool for operations different from those
intended could result in a hazardous situation.

4

Service

23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

24. Follow instruction for lubricating and changing
accessories.

25. Keep handles dr y, clean and free from oil and
grease.

ADDITIONAL SAFETY RULES

1. Always use protective goggles, a cap and mask
when using the blower.

2. Never point the nozzle at anyone in the vicinity
when using the blower.

3. Always use the dust bag when collecting dust,
chips and the like.

4. Do not collect still smoldering cigarette ashes or
freshly cut metals shavings. Warning – Electric
shock could occur if used on wet surfaces. Do
not expose to rain. Store indoors.

5. Never block suction inlet and/or blower outlet.
Increased motor revolution may cause danger­ous fan breakage.

6. The tool is not intended for use by young chil­dren or infirm persons without supervision.

7. Young children should be supervised to ensure
that they do not play with the tool.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Blowing (Fig. 1)

For dust blowing, attach nozzle to blower outlet, turning
clockwise to lock it in place.

Dust suction (Fig. 2 & 3)

Note:
Dust bags are optional accessories in some countries.

For dust suction, fit nozzle onto suction inlet and dust
bag onto blower outlet.

After the bag fills with dust, empty the contents of the
dust bag into a dust bin by releasing the fastener.

Switch action

CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.

For 4014N (Fig. 4)

To start the tool, simply pull the trigger. Release the trig­ger to stop. For continuous operation, pull the trigger and
then push in the lock button. To stop the tool from the
locked position, pull the trigger fully, then release it.

For 4014NV (Fig. 5)

To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop. For continuous operation, pull the trig­ger and then push in the lock button. To stop the tool from
the locked position, pull the trigger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclockwise
for lower speed.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.

Replacement of carbon brushes (Fig. 6 & 7)

Replace carbon brushes when they are worn down to the
limit mark. Both identical carbon brushes should be
replaced at the same time.

To maintain product safety and reliability, repairs, mainte­nance or adjustment should be carried out by a Makita
Authorized Service Center.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.

If you need any assistance for more details regarding
these accessories, ask your local Makita service center.

•Joint

•Flexible hose

• Corner nozzle

• Straight pipe

• Nozzle assembly

• Nozzle assembly (long size)

• Dust bag assembly

5

6

7

Makita Corporation

Anjo, Aichi, Japan

883440A221