Makita 3706 User guide
Cutout
Tool
MODEL
INSTRUCTION MANUAL
3706
SPECIFICATIONS
load
speed
Collet chuck capacity
1/4",
1/8"
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country to country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
No
(RPM)
32,0001min.
Overall length Net weight
250
mm
(9-7/8")
DOUBLE
INSULATION
1.1 kg (2.4
Ibs)
GENERAL SAFETY RULES
USAW2-’
(For
WARNING! Read and understand
All
Tools)
all
instructions.
Failure
to follow all instructions listed below, may result in electric
shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
1.
Keep your work area clean and well
accidents.
2.
Do not operate power tools
of flammable liquids, gases, or dust. Power tools create sparks which may
ignite the dust or fumes.
3.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
4.
Double Insulated tools are equipped
than the other.)
plug does not
contact a qualified electrician to install a polarized outlet. Do not change
the plug
wire grounded power cord and grounded power supply system.
5.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk
grounded.
6.
Do not expose power tools to rain or wet conditions. Water entering a power
tool
7.
Do not abuse the cord. Never use the cord to carry the tools or pull the plug
from an outlet. Keep cord away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged cords increase the risk
electric shock.
8.
When operating a power tool outside, use an outdoor extension cord marked
“W-A“ or “W.“ These cords are rated for outdoor use and reduce the risk
of electric shock.
Personal Safety
9.
Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools
may result
IO.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry
or long hair can be caught
in
will
increase the risk
This
fit
fully
any way. Double insulation eliminates the need for the three
in
serious personal injury.
in
plug
will
in
the outlet, reverse the
of
in
lit.
Cluttered benches and dark areas invite
explosive atmospheres, such as in the presence
with
a polarized plug (one blade is wider
fit
in a polarized outlet only one way.
plug.
If
it
of
electric shock if your body is
electric shock.
moving parts.
still does not
If
the
fit,
of
2
11.
Avoid accidental starting. Be sure switch is off before plugging
tools with your finger on the switch or plugging in tools that have the switch
on invites accidents.
12. Remove adjusting keys or wrenches before turning the tool on. A wrench
a
key that is left attached to a rotating part
or
injury.
Do
13.
14.
Tool
15. Use clamps or other practical way to secure and support the workpiece to
16.
17.
18.
19. Store idle tools out
20.
21. Check for misalignment or binding of moving parts, breakage of parts, and
22.
SERVICE
23.
24. When servicing a tool, use only identical replacement parts. Follow
not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
Use and Care
a stable platform. Holding the work by hand or against your body is unstable
loss
and may lead to
Do not force tool. Use the correct tool
will do the job better and safer
Do not use tool if switch does not turn
be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the
reduce the risk of starting the tool accidentally.
are
dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges are less likely to bind and are easier
to control.
any other condition that may affect the tools operation.
the tool serviced before using. Many accidents are caused by poorly
maintained tools.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool, may become hazardous
when used on another tool.
Tool
service
or maintenance performed
injury.
instructions
parts or failure to follow Maintenance Instructions may create a risk of electric
shock or injury.
must
in
the Maintenance section of this manual. Use
of control.
at
the rate for which
tool.
of
reach of children and other untrained persons.
be
performed only by qualified repair personnel. Service
by
unqualified personnel could result in a risk
of
the tool may result in personal
for
your application. The correct tool
it
is designed.
it
on or off. Any tool that cannot
Such preventive safety measures
in.
Carrying
If
damaged, have
of
unauthorized
Tools
of
3
Loading...