MAKERFACTORY MAKEVMA100, MAKEVMA101, MAKEVMA102, MAKEVMA103 User guide
MAKEVMA100/MAKEVMA101/
DEVELOPMENT BOARD
MAKEVMA100
MAKEVMA101
MAKEVMA102
MAKEVMA103
USER MANUAL
MAKEVMA102/MAKEVMA103
MAKEVMA100/MAKEVMA101/MAKEVMA102/MAKEVMA103
This device can be used by children aged from 8 years and above, and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning the use of the device in a
safe way and understand the hazards involved. Children shall not play with the device.
Cleaning and user maintenance shall not be made by children without supervision.
Indoor use only.
Keep away from rain, moisture, splashing and dripping liquids.
Familiarise yourself with the functions of the device before actually using it.
All modifications of the device are forbidden for safety reasons. Damage caused by user
modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way
will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the
warranty and the dealer will not accept responsibility for any ensuing defects or
problems.
The dealers cannot be held responsible for any damage (extraordinary, incidental or
indirect) – of any nature (financial, physical…) arising from the possession, use or
failure of this product.
Due to constant product improvements, the actual product appearance might differ from
the shown images.
Product images are for illustrative purposes only.
Do not switch the device on immediately after it has been exposed to changes in
temperature. Protect the device against damage by leaving it switched off until it has
reached room temperature.
Keep this manual for future reference.
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could
harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device should be returned to your
distributor or to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Please read the manual thoroughly before bringing this device into service. If the device was damaged in
transit, do not install or use it and contact your dealer.
2. Safety Instructions
3. General Guidelines
V. 01 – 07/11/2017 2
MAKEVMA100/MAKEVMA101/MAKEVMA102/MAKEVMA103
MAKEVMA100
The MAKEVMA100 (Arduino® Uno compatible) is a microcontroller board based on the ATmega328. It has 14
digital input/output pins (of which 6 can be used as PWM outputs), 6 analogue inputs, a 16 MHz ceramic
resonator, a USB connection, a power jack, an ICSP header and a reset button. It contains everything
needed to support the microcontroller. Connect it to a computer with a USB cable or power it with an AC-toDC adapter or battery to get started.
1
USB interface
6 16 MHz clock
2
reset button
7 Atmel mega328p (DIL)
3
digital I/O
8 7-12 VDC power input
4
Atmel mega16U2
9 power and ground pins
5
ICSP
10
analogue input pins
microcontroller .................................................................................................. ATmega328
operating voltage ....................................................................................................... 5 VDC
input voltage (recommended) ................................................................................ 7-12 VDC
input voltage (limits) ............................................................................................. 6-20 VDC
digital I/O pins ................................................................ 14 (of which 6 provide PWM output)
analogue input pins ........................................................................................................... 6
DC current per I/O pin ............................................................................................... 40 mA
DC current for 3.3 V pin ............................................................................................. 50 mA
flash memory ...................................... 32 kB (ATmega328) of which 0.5 kB used by bootloader
SRAM .................................................................................................... 2 kB (ATmega328)
EEPROM.................................................................................................. 1 kB (ATmega328)
clock speed ............................................................................................................. 16 MHz
dimensions
length .............................................................................................................. 68.6 mm
width ............................................................................................................... 53.4 mm
weight ................................................................................................................... 25 g
4. What is Arduino
Arduino® is an open-source prototyping platform based in easy-to-use hardware and software. Arduino® boards
are able to read inputs – light-on sensor, a finger on a button or a Twitter message – and turn it into an output
– activating of a motor, turning on an LED, publishing something online. You can tell your board what to do by
sending a set of instructions to the microcontroller on the board. To do so, you use the Arduino programming
language (based on Wiring) and the Arduino® software IDE (based on Processing).
Surf to www.arduino.cc and www.arduino.org for more information.
®
5. Overview
V. 01 – 07/11/2017 3
Loading...