Majestic fireplaces ODGSR36A, ODGSR42A, ODGSR36ARN, ODGSR36ARP, ODGSR42ARN Homeowner's Installation And Operating Manual
...
Outdoor Gas Fireplace
D
E
S
I
G
N
C
E
R
T
I
F
I
E
D
CER TIF IED
Models:
ODGSR36A, ODGSR42A
INSTALLER/CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE.
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
do not use any phone in your
building.
• Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
• If you cannot reach your gas
supplier, call the fire department.
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
WARNING:
Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage. Read the installation,
operating and maintenance instructions
thoroughly before installing or servicing
this equipment.
WARNING:
For Outdoor Use ONLY.
Homeowner's Installation and
Operating Manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
20007114 4/08 Rev. 10
ODGSR Series Outdoor Gas Fireplace
Table of Contents
Thank you and Congratulations on your purchase of a CFM Corporation fireplace.
PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING THE APPLIANCE
IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these
instructions may result in a possible fire hazard and will void the warranty.
Installation & Operating Instructions ..........................................................................................3
General Information .............................................................................................................3
Fireplace Dimensions .......................................................................................................... 4
Moisture Resistance ............................................................................................................ 5
Screened Porch Installation ................................................................................................5
Clearance to Combustibles .................................................................................................5
Mantels ............................................................................................................................... 5
Hearth ...............................................................................................................................5
Moisture Resistance ............................................................................................................ 6
Framing & Finishing ............................................................................................................6
Final Finishing .....................................................................................................................6
Gas Specifications ...............................................................................................................7
Gas Inlet & Manifold Pressures ........................................................................................... 7
High Elevations ...................................................................................................................7
Valve Access .......................................................................................................................7
Exterior Chase Installation ..................................................................................................8
Gas Line Installation ............................................................................................................ 8
Remote Wall Switch ............................................................................................................9
Operating Instructions
Log Installation ..................................................................................................................10
Lava Rock .........................................................................................................................10
First Firing .........................................................................................................................10
Flame Adjustment .............................................................................................................. 11
Flame Characteristics ........................................................................................................ 11
Optional Weather Enclosures ............................................................................................12
Optional Stainless Steel Hood ...........................................................................................12
Lighting & Operating Instructions ......................................................................................13
Troubleshooting .................................................................................................................14
Maintenance .................................................................................................................................15
Replacement Parts ...................................................................................................................... 16
Accessories ..................................................................................................................................18
Warranty ....................................................................................................................................... 19
IMPORTANT:
PLEASE READ THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace “ON”.
It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle. Similar noises are found
with your furnace heat exchanger or car engine.
It is not unusual for your Majestic Fireplaces gas fire
place to give off some odor the first time it is burned.
This is due to the curing of the paint and any undetected oil used in the manufacturing process.
It is recommended that you burn your fireplace for at
least ten (10) continuous hours the first time you use it.
2
Proposition 65 Warning:
burning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects
and other reproductive harm.
California Health & Safety Code Sec. 25249.6
-
Fuels used in gas, wood-
20007114
General Information
This gas appliance should be installed by a qualified
installer in accordance with local building codes and with
current CSA-B149.1 Installation codes for Gas Burning
Appliances and Equipment.
FOR U.S.A Installations follow local codes and/or the current National Fuel Gas Code. ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings
and installation of this heater shall only be done by a
licensed gas fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION PLEASE
NOTE THE FOLLOWING:
1. This appliance gives off high temperatures and should be
located out of high traffic areas and away from furniture.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this appliance and should stay
away to avoid burns or ignition of clothing.
3. Children should be carefully supervised when they are in the
same room as your appliance.
4. Under no circumstances should this appliance be modified.
Parts having to be removed for servicing should be replaced
prior to operating this appliance again.
5. Installation and any repairs to this appliance should be carried out by a qualified service person. A professional service
person should be contacted to inspect this appliance annually. Make it a practice to have all of your gas appliances
checked annually. More frequent cleaning may be required
due to excess lint and dust from carpeting, bedding material,
etc.
6. Control compartments, burners and air passages in this ap
pliance should be kept clean and free of dust and lint. Make
sure that the gas valve and pilot light are turned off before
you attempt to clean this unit.
7. Keep the area around your appliance clear of combustible
materials, gasoline and other flammable vapor and liquids.
This appliance should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung
in the area of it.
8. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard etc.) be used in this appliance.
9. The flow of combustion and ventilation air must not be ob
structed in any way.
10. Whether the appliance is installed directly on carpeting, vinyl
tile or any combustible material other than wood, this appliance must be installed on a metal or wood panel extending
the full width and depth of the appliance.
11. This appliance requires adequate ventilation and combus
tion air to operate properly.
12. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system or
gas control that has been under water.
13. Inspect the burner before each use of the appliance. The
burner must be replaced prior to operation if there is evidence the burner is damaged. Use only burner specified by
manufacturer.
LP-cylinder enclosures, if provided by the consumer must conform to the design parameters as detailed below.
20007114
-
-
-
ODGSR Series Outdoor Gas Fireplace
Enclosures for LP-Gas Supply Systems
Enclosures for LP-gas supply cylinders shall be ventilated by
openings at the level of the cylinder valve and at floor level. The
effectiveness of the opening(s) for purposes of ventilation shall
be determined with the LP-gas supply cylinder(s) in place. This
shall be accomplished by one of the following:
a. One side of the enclosure shall be completely open; or
b. For an enclosure having four sides, a top and a bottom:
1. At least two ventilation openings at cylinder valve level
shall be provided in the side wall, equally sized, spaced at
180 degrees (3.14rad), and unobstructed. Each opening
shall have a total free area of not less than 1/2 square
inch per pound (3.2 sq. cm/kg) of stored fuel capacity and
not less than a total free area of 10 square inches (64.5
sq. cm).
2. Ventilation opening(s) shall be provided at floor level and
shall have a total free area of not less than 1/2 square
inch per pound (3.2 sq. cm/kg) of stored fuel capacity and
not less than a total free area of 10 square inches (64.5
sq. cm). If ventilation openings at floor level are in a side
all, there shall be at least two openings. The bottom of
the openings shall be at floor level and the upper edge no
more than 5 inches (127 mm) above the floor. The open
ings shall be equally sized, spaced at 180 degrees (3.14
rad) and unobstructed.
3. Every opening shall have minimum dimensions so as to
permit the entrance of a 1/8 inch (3.2 mm) diameter rod.
Cylinder valves shall be readily accessible for hand operation.
A door on the enclosure to gain access to the cylinder valves
is acceptable, provided it is non-locking and can be opened
without the use of tools.
There shall be a minimum clearance of 2 inches (51 mm)
between the lower surface of the floor of the LP-gas supply
cylinder enclosure and the ground.
The design of the appliance shall be such that (1) the LP-gas
supply cylinder(s) can be connected, disconnected and the
connections inspected and tested outside the cylinder enclosure; and (2) those connections which could be disturbed when
installing the cylinder(s) in the enclosure can be leak tested
inside the enclosure.
Description
The ODGSR Series are radiant fireplaces. Do not burn wood
or other materials in these appliances. Each model is available
with standing pilot for use with Natural or Propane gas units.
Report to your dealer any parts damaged in shipment.
Adequate combustion and ventilation air must be provided. The
flow of combustion and ventilation air MUST NOT be obstructed.
Provide adequate clearances around the air opening into the
combustion chamber; and adequate accessibility clearance for
servicing and proper operation. NEVER obstruct the front opening of the appliance.
This fireplace is not designed to be water tight.
Therefore, when installing this unit against an exterior wall, the wall must be finished before setting unit
in place.
-
3
ODGSR Series Outdoor Gas Fireplace
42"
(1067mm)
46"
(1168mm)
39
"
(1007mm)
" (16mm)
50" (1270mm)
50" (1270mm)
" (13mm)
"
" (1791mm)
"
(610mm)
43"
(1111mm)
"
(191mm)
"
(165mm)
"
(191mm)
Rough
Opening
Height
"
(16mm)
22"
(559mm)
"
(572mm)
"
(667mm)
Recessed
Nailing
Flange
Rough Opening Width 47"
Rough
Opening
Depth
3"
(76mm)
35" (895mm)
(1194mm)
14"
(362mm)
3"
(95mm)
Low Voltage
Wire Access
Gas Line Access
14"
(362mm)
Low Voltage
Wire
Access
36"
(914mm)
40"
(1016mm)
39
"
(1007mm)
" (16mm)
" (13mm)
"
" (822mm)
"
(622mm)
43"
(1111mm)
8"
(210mm)
"
(165mm)
"
(191mm)
Gas Line Access
Rough
Opening
Height
"
(16mm)
22"
(559mm)
"
(572mm)
" (559mm)
Recessed
Nailing
Flange
Rough Opening Width 41"
Rough
Opening
Depth
3"
(95mm)
(1041mm)
3"
(98mm)
68" (1740mm)
48" (1232mm)
48" (1232mm)
14"
(362mm)
3"
(95mm)
Low Voltage
Wire Access
14"
(362mm)
Low Voltage
Wire
Access
Fireplace Dimensions
Fig. 1 ODGSR36A specification and framing dimensions.
Fig. 2 ODGSR42A specification and framing dimensions.
4
Fireplace Dimensions
20007114
ODGSR Series Outdoor Gas Fireplace
A
B
Y
Z
Fireplace
Moisture Resistance
This outdoor fireplace will shed moderate amounts of
water, but is not waterproof. Water and condensing water vapor may enter the chase under certain conditions.
The fireplace will not perform as an exterior wall. Moisture penetration must be considered for construction
that places the fireplace in structure walls or on moisture sensitive surfaces.
When installed on exterior walls: CFM Corporation
recommends the fireplace chase be constructed outside
the structure's weather envelope. Where the platform
meets the wall, use a flashing detail similar to that
required for attached decks. Chase platforms, including
hearths should slope away from the structure at 1/4 in
per foot. The fireplace can be shimmed level.
When installed on surfaces where water may collect or
cause damage: CFM Corporation recommends a slope
of 1/8 in to 1/4 in per foot towards the drain port suggested. The fireplace can be shimmed level.
Hearths should slope away from the front of the fireplace and chase at 1/8 in to 1/4 in per foot. Metal safety
strips must be on top of any combustible hearth materials used for moisture management.
Mantels
WARNING: A 4" hood must be used if a
mantel is to be installed.
The height that a combustible mantel is fitted above the
fireplace is dependent on the depth of the mantel. This
also applies to the distance between the mantel leg (if
fitted) and the fireplace.
For the correct mounting height and widths refer to
Figures 3a and 3b
Noncombustible mantels and legs may be installed at
any height and width around the appliance.
When using paint or lacquer to finish the
mantel, such paint or lacquer must be heat
resistant to prevent discoloration.
Side View
Maintain minimum
3/4" (19 mm)
clearance to
combustible.
Standoff
Screened Porch Installation
The ODGSR may be installed safely and is design
certified by CSA to be installed in a screened porch with
these guidelines:
Minimum porch area ..............................96 sq. feet (9 sq m)
Minimum celing height ..................................... 92" (234 cm)
Minimum of two (2) walls must be screened
Minimum top of screen height, side walls ........
Minimum screen area ............................64 sq. feet (6 sq m)
6'6" (198 cm)
Clearance to Combustibles
Appliances
Top ..........................................................0” (0 mm)
Bottom .....................................................0” (0 mm)
Side .........................................................0” (0 mm)
Back ........................................................0” (0 mm)
Perpendicular Sidewall ...........................0” (0 mm)
Top of unit to ceiling ..........................36” (914 mm)
Front of unit to combustibles .............36” (914 mm)
Top of Combustion
Chamber
CFM146
Ref. Mantel Ref. Mantel From Top
Shelf Depth of Comb. Chamber
Y 8" (203 mm) A 28" (711 mm)
Z 1
Fig. 3a Mantel clearances.
¹⁄₂" (38 mm) B 26" (660 mm)
Hearth
A hearth is not mandatory but is recommended for
aesthetic purposes. We recommend a noncombustible
hearth.
20007114
5
ODGSR Series Outdoor Gas Fireplace
J
F
G
H
I
Mantel
Leg
O
N
M
L
K
Black
Surround
CFM164
Ref. Mantel Ref. Mantel Leg From
Leg Depth of Comb. Opening
F 14" (356 mm) K 14" (356 mm)
G 12" (305 mm) L 12" (305 mm)
H 10" (254 mm) M 10" (254 mm)
I 8" (203 mm) N 8" (203 mm)
J 1¹⁄₂" (38 mm) O 1¹⁄₂" (38 mm)
Fig. 3b Combustible mantel leg minimum installation.
Face
Side of
Combustion Chamber
CFM170
Moisture Resistance
Hearths should slope away from the front of the fire
place and chase at 1/8 in to 1/4 in per foot. Metal safety
strips must be on top of any combustible hearth materials used for moisture management.
Framing and Finishing
Check appliance to make sure it is levelled
and properly positioned.
The appliance should only be mounted on the following
surfaces:
• A flat combustible (burnable) surface.
• A raised wooden platform.
• A concrete block or other solid object placed
beneath each of the four corners of the appliance.
To mount the appliance:
1. Choose unit location.
2. Four (4) nailing flanges are supplied with the fire
place (found on the fireplace hearth). To level the
box and secure it firmly in place, remove the nailing
flanges from the hearth and install at the sides of the
fireplace as shown in Figure 4.
-
Nail Top
Standoffs
Nail SideNailing
Flanges
This outdoor fireplace will shed moderate amounts of
water, but is not waterproof. Water and condensing water vapor may enter the chase under certain conditions.
The fireplace will not perform as an exterior wall. Moisture penetration must be considered for construction
that places the fireplace in structure walls or on moisture sensitive surfaces.
When installed on exterior walls: CFM Corporation
recommends the fireplace chase be constructed outside
the structure's weather envelope. Where the platform
meets the wall, use a flashing detail similar to that
required for attached decks. Chase platforms, including
hearths should slope away from the structure at 1/4 in
per foot. The fireplace can be shimmed level.
When installed on surfaces where water may collect or
cause damage: CFM Corporation recommends a slope
of 1/8 in to 1/4 in per foot towards the drain port suggested. The fireplace can be shimmed level.
6
FP549
Fig. 4 Adjustable drywall strip (nailing flange).
Finishing
CAUTION: All joints between the finished
wall and the appliance surround (top and
sides) may be sealed only with non-combustible material. Only noncombustible
material can be applied as facing to the ap-
pliance surround (the black painted face).
Finish the wall with the material of your choice. Refer to
Figures 3a and 3b for specific clearances when installing a combustible mantel or other combustible projection.
20007114
Loading...