Majestic MARQ36IN Specifications

Specifications

Please consult the manufacturer’s

installation manual for all details and

requirements before making a final

MARQUIS II 36

Direct Vent Gas Fireplace

design layout decision.

MODEL HEIGHT FRONT WIDTH BACK WIDTH DEPTH GLASS SIZE

MARQ36IN

Actual Framing Actual Framing Actual Framing Actual Framing

57-5/8"

[1464]

56"

[1422]

61"

[1549]

59-1/2"

[1511]

59-1/4"

[1505]

59-1/2"

[1511]

24"

[610]

24"

[610]

35-7/8" x 31-1/16"

[911 X 789]

TOP VIEW

59-1/4" [1505]

29-5/8"

[752]

16"

[406]

MARQ36IN

Heat-Zone

Port

Gas

Access

2-3/4"

[70]

16-1/8"

[410]

FRONT VIEWLEFT SIDE RIGHT SIDE

24"

[610]

®

Electrical

Access

31-1/16"

[789]

3-7/8"

[98]

10-7/8"

[276]

61" [1549]

40-11/16" [1035]

57-5/8"

[1464]

54-15/16"

[1395]

23-1/2"

[597]

Heat-Zone

®

Port

41-3/8"

[1051]

DECORATIVE FRONT

40-11/16"
[1035 mm]

3-5/8"
[92 mm]

35-9/16"
[903 mm]

1-5/16"
[33 mm]

36-13/16"
[935 mm]

Specifications

"

59-1/2" [1511]

74-1/4" [1886]

74-1/4

74-3/16

*Shows center of vent framing hole with

fireplace to ceiling

MARQ36IN

APPLIANCE LOCATION

26-1/2"

[673]

26-1/2"

[673]

[597]

59-1/2"

[1511]

105"

[2667]

29-3/4"

[756]

59-1/2"

[1511]

[1886]

"

23-1/2"

WALL PENETRATION

Do not pack with insulation
or other material.

10"

12"

73-3/16"

"*

minimum vertical for top venting.
Center of hole is 1" above center of
horizontal vent pipe.
*Add height for chase deeper than 24".

MANTEL LEG/WALL PROJECTIONS

Combustible Mantel

1/2" Building material

Combustible

column

Fireplace

opening

Factory-supplied
non-combustible

board

Combustible or

non-combustible wall

Non-combustible Mantel

7" min

14" min

4" maximum

Factory-supplied
non-combustible

board

Fireplace

opening

Non-combustible

column

See section 13.E
for required
clearances

14" min

1/2" Building material

MANTEL PROJECTIONS

1/2 IN NON-COMBUSTIBLE MATERIAL

FIREPLACE
OPENING

MAX.

12

9

6

3

1

55

52

49

46

Note: All measurements in
inches.

58

Note: Measurement is taken
from bottom of appliance.

MIN.

Note: Measurement from
fireplace opening to bottom
of appliance is 35-3/16".

29-3/4

23-1/2"

[597]

6" maximum

Combustible or

non-combustible wall

[756]

FRAMING DIMENSIONS

10"

[254]

56"

[1422]

24"

59-1/2" [1511]

[610]

CLEARANCES TO COMBUSTIBLES

0"

Note: A 12" non-combustible
hearth extension is required.
The replace may be raised
from the oor a minimum of
3" to eliminate this
requirement. See installation
manual for more details.

See

install manual

section 3.D

36"

[914]

[25]

1"

NON-COMBUSTIBLE ZONE

2" x 4" OR GREATER
FRAMING MATERIAL

1/2" BUILDING MATERIAL

(MAY BE COMBUSTIBLE)

NO COMBUSTIBLES

IN HATCHED AREA

2" x 4" ONLY IN
GRAY AREA

2" x 4" HEADER

CONFIGURATION

FACTORY-SUPPLIED

1/2"

NON-COMBUSTIBLE

BOARD

NOTE:

1"

PIPE IS FOR VISUAL

REFERENCE ONLY

Product information provided
is not complete and is subject
to change without notice.

39"

Product installation must
adhere strictly to instructions
accompanying product to
avoid risk of fire and potential
injury.

52"

[1321]
from appliance

opening to
ceiling

87-3/16" [2215]
from bottom of

1"

[25]

PRODUCT LISTING CODES

US ANSI Z21.88-2009

CAN CSA 2.33-2009

UL307B

Combustible Mantel
Projections shown.
See installation manual for
Non-combustible Mantel
Projections

[phone] • www.majesticproducts.com

= COMBUSTIBLES

NOT ALLOWED

MAJ/MARQUISII_MARQ36IN_0917