Page 1
4.3 & 5.0 OCTAVES
DELUXE / ARTIST / PROFESSIONAL
MARIMBA
WWW.MAJESTIC-PERCUSSION.COM
Ver. 201307
I. Components P1
P4
P2
P5
II. Build the frame P3
III. Set up Resonators P6
Assembly Instruction
Item Parts Description
1 Leg Assembly - Bass End x 1
2 Leg Assembly - Treble End x 1
3 Center Cross Bar x 1
4 Leg support x 2
5 Side Frame – Bass End x 1
6 Side Frame – Treble End x 1
7 Rails (no.1~ no.4) x 4
8 Resonator- Naturals for 4.3 Oct Model x 2
9 Resonator- Accidentals for 4.3 Oct Model x 2
10 Tone Bars-Naturals x 1
11 Tone Bars-Accidentals x 1
12 Protective Cover x 1
13 Mallets x 1
Resonator For 5.0 Oct Model
14 Resonator-Naturals Bass-section x 1
15 Resonator-Accidentals Bass-section x 1
16 Resonator-Naturals Mid-section x 1
17 Resonator-Accidentals Mid-section x 1
18 Resonator-Naturals Treble-section x 1
19 Resonator-Accidentals Treble-section x 1
●
Assembly leg
Begin the process by assembling leg support to
center crossbar with provided knob screw.
With Bass End Leg Assembly lying flat on the ground,
place the Center Cross Bar in to square housing at
position (A) and position (B). Align the hole, insert
knob screw in and tighten with moderate pressure.
Set the Bass End Leg Assembly upright, cross bars
are horizontal to ground, repeat the process on Treble
End Leg Assembly.
Engage brakes before setting Leg Assembly in upright
position. This will provide stability and traction. Wheels
with brake should be positioned facing playing side.
●
Assembly rails
Using labels on rails and frame end brackets as guide,
attached rails to corresponding position on the side
frame. Numbering are labeled on bass end of rails and
side frame.
Please begin assembly rails with sequence of
no.3 → no.2 → no.1 → no.4.
●
Attach resonators
Resonators are setup under the frame. Pick up one
resonator, make sure suspension arms is at open
position; attach resonator set by seating arms firmly
into notches on side frame & rails.
1
3
4
7
6
8
10
12
A
B
●
Assemble side frames
Standing in the playing posiition with the wheel with
break facing you, set the bass end side frame on top
of the leg assembly. Match the holes with the knob
screws, then tighten with moderate pressure. Repeat
this process at treble end.
Treble End (small end) is to your right, Bass End
(Large End) is to your left.
9
2
5
11
14 15
18
19
13
16 17
For 5.0 Oct Model
For 4.3 Oct Model
For 4.3 Oct Model
For 4.3 Oct Model
For 5.0 Oct Model
For 5.0 Oct Model
Page 2
●
Unroll the bars
Carefully unroll the tone bars on the flat floor, flip the
bars over so that the playing side faces up (arch side
faces down). Keep out the springs and sharp
object away from tone bar. Prevent scratch or
damages to bar surface.
Use soft wrapping to protect bars, do not scratch.
●
Tone bar leveling
Due to the resonator weight, the rail might sag in the
middle after resonators are attached. This can be
corrected by extension screw length located inside
hinged center.
M7550H
M6543D
Memo P14
P7
V. Other Adjustment P11 P12 VI. Finished View P13
IV. Place Toner bars P8 P9 P10
●
Connect stabilizer bracket
For better resonator stability, you can find stabilizer
arms locate on the rail side.
Pull up the arms, swing over resonator top and insert
to corresponding rubber notch. Press down to
complete the assembly.
●
Position tone bars
Place the Natural note bars on top of the lower rails
(close to player side).
Position each tone bar in between bar posts, begin
from treble end, working progressively down towards
bass end.
Repeat above process with accidentals (refer to C
chromatic scale), placing tone bars over capped
resonators only. Open resonators should have no bar.
●
Fasten Cord & spring
Once tone bars are in place, pull excess bar cord
through bass end, bring bar cord around end posts
and hook the springs together
.
The springs has a small tension after they are
booked. You can adjust knot on the cord to get
different tensions after springs are connected.
●
Instrument Height
You can elevate or lower the Instrument height by
tuning the hand crank handle located on each side of
instrument. Use imprinted scale guide for leveling.
To maintain balance of adjustment, atjust one
end at a time, do not exceed 2” increment at a time.
For 5.0 Oct ModelFor 4.3 Oct Model
Loading...