Majestic DSR42 Specifications

PRODUCT SPECIFICATIONS

DSR42 Designer See-Through Radiant Wood Burning Fireplace

47" [1194]

DIMENSIONS

Actual size: 47" W x 587⁄8" H x 28" D

(1016 mm x 1022 mm x 610 mm)

Viewing area: 42" W x 23" H (966 sq. in.)

(1067 mm X 584 mm, 6233 cm

Framing Dimensions: 48" W x 39

⁄8" H x 27" D

)

(1219 mm x 994 mm x 686 mm)

STANDARD FEATURES

• Clean face design and fully insulated see through ﬁreplace

• Full refractory lining

• Authentic masonry appearance

• Powder coated ﬁnish

• Safety ﬁrescreen

• Dual gas knockouts

• Steel grate

• Outside air kit standard

• Attic insulation shield standard

• UL/ULC Listed

OPTIONAL FIELD INSTALLED ACCESSORIES

• Bi-fold glass doors with Black trim (DM1242)

• SL1100 series termination caps

• 4" insulated ﬂex duct for outside air (ID4)

• 4" uninsulated ﬂex duct for outside air (UD4)

• Chimney air kit (CAK4A)

• Gas logs available

Top View

Front View

Right Side View

28"

[711]

23-1/2"

[597]

Ø13" [330]

58-7/8"

[1496]

effective

height

23"

[585]

42" [1067]

1/2” 1/2”

Outside

Gas

Knockout

8-3/8" [213]

Framing dimensions in illustrations

accommodate 1/2" finishing material.

14"

[356]

Air

8-5/8"

[319]

7-1/2"

[192]

38-3/8"

[975]

11-3/4"

[398]

39-1/8"

[994]

14"

[356]

39-1/8"

[995]

Page 1 of 2

Note: DSR42 is not approved for sale or use in

Canada.

PRODUCT SPECIFICATIONS

Combustible Wall

2 x 4

stud wall

Standoffs

Measured from top of fireplace opening

12 in./305 mm

1 1/ 2 in.

38 mm

maximum

Mantel

6 in./152 mm

minimum

12 in./305 mm

minimum

Combustible Decorative Facing

Non-combustible Decorative Facing such as: Steel, iron, brick, tile, concrete, slate, tile, plasters

Seal joint with non-combustible sealant

Grid lines at 1 in. scale

7 ft (2134 mm)

minumum

base of fireplace

to ceiling

DSR42 Designer See-Through Radiant Wood Burning Fireplace

MANTEL CLEARANCES

TECHNICAL SPECIFICATIONS

• Flue series: SL1100 series pipe

• Flue size: 11" (279 mm) inner; 13" (330 mm) outer

• Clearance to ﬂue: 2" (51 mm)

• Firestop framing: 17" x 17" (432 mm x 432 mm)

• Minimum ﬂue height: 14' (4.3 m)

• Maximum ﬂue height: 90' (27.4 m)

• Minimum height with single offset/return: 16.5' (5 m)

• Minimum height with double offset/return: 22' (6.7 m)

• Minimum hearth size: 20" D x 66" L (508 mm x 1676 mm)

• UL/ULC design certiﬁed

CLEARANCES

• Clearance to ﬁreplace: 1⁄2” (13 mm)

• Maximum mantel depth: 12" (305 mm) from top of

ﬁreplace opening

• Minimum mantel height: 6" (152 mm) from top of ﬁreplace opening

• Adjacent combustible sidewalls: minimum 12" (305 mm) from

ﬁreplace opening

• Mantel leg, surround, stub wall, whether combustible or

non-combustible may be constructed as shown in the

second drawing.

SURROUND, STUB WALL, MANTEL LEG CLEARANCES

Gridlines at 1 in. scale

FLUSH FRONT

11 3/8 in. [289 mm]

To avoid personal injury or property damage, the product described by this brochure must be installed, operated and maintained in strict compliance with the instructions packaged with the product and all applicable building or ﬁre codes. Contact local building or ﬁre ofﬁcials about restrictions and installation inspection requirements. All photographs and drawings on this brochure are for illustrative purposes only and are not intended for, nor should they be used as a substitute for the instructions packaged with the unit. Appearance and speciﬁcations of the product are subject to change without notice. © 2015 Vermont Castings Group 0415v1

50° angle

12 in.

[305 mm]

42 in.

[1067 mm]

fireplace opening

47 in.

[1194 mm]

width of fireplace

[305 mm]

BRICK

FRONT

39° angle

12 in.

4 in.

[102 mm]

9 3/4 in.

[248 mm]

A Brand of Vermont Castings Group

149 Cleveland Drive, Paris, Kentucky 40361

www.majesticproducts.com

Page 2 of 2