Majestic concert marimba, concert vibraphone, concert xylophone Assembly Instructions Manual

Mallet

Instrument

Assembly Instructions

Concert Marimba — 4 Octave Model
Concert Xylophone — 4 & 3-1/2 Octave Model
Concert Vibraphone — 3 Octave Model

產品組立說明書：

室內型立奏低音木琴 — 4 個八度音型號
室內型立奏高音木琴 — 4 & 3-1/2 個八度音型號
室內型立奏顫音鋁琴 — 3 個八度音型號

P2

Check contents carefully. Each model should include following:

每一組琴應該要包括下列組件，請仔細檢查內容：

Materials 零件

1

2

3

4

5

6

7

8

9

Item Parts Description 零件敘述 Qty 數量

1 Leg Assembly with 4" Casters 木琴側架含 4" 腳輪 2 Units
2 Cross Bar 方型連結桿 1 PC
3 Curved Brace 圓弧形支撐架 2 PC
4 Pedal Assembly (Vibraphone Only) 踏板組件（顫音鋁琴） 1 Unit
5 Keyboard Frame 琴框 1 PC
6 Resonator Set (Naturals & Accidentals) 共鳴管 ( 全音 & 半音） 2 Units
7 Tone Bar Set (Naturals & Accidentals) 音板組 ( 全音 & 半音） 2 Units
8 Protective Cover 琴罩 1 PC
9 Keyboard Mallet 琴槌 1 Pair

P3

Frame Set Up & Resonator Attachment

琴架、琴框、共鳴管組裝

1

2

Connect curved braces to cross bar with hand knob. Do not tighten.

將圓弧形支撐架與方形連結桿以旋鈕結合，但請勿鎖緊。

Identify low end leg assembly. With leg assemblies
lying flat with the height adjustment crank handle on
the floor and the crossbar receivers facing up, the low
end leg will have the wheel with brake on the left.

For xylophone and marimba, insert one end of the
crossbar into receiver (A), and an end of the curved
brace into receiver (B). Tighten hand knob at position
(B) first, then the other hand knobs at position (A) &
(C).

For vibraphone, insert one end of the crossbar
into receiver (B), and an end of the curved brace
into receiver (A). Pedal brackets should be on the
underside of the crossbar with the pedal facing toward
the player (wheel with brake) side of the instrument.
Pull rods should protrude on the top side of the pedal.
Tighten hand knobs at positions (A)&(C) first, then the
hand knob at position (B).

將低音側琴架平放，再將連結桿組件插入琴架 (A) 位置，
圓弧形支撐架插入琴架 (B) 位置；先確保 (B) 處旋鈕可
鎖入圓弧形支撐架孔內，再將 (A) 處與 (C) 處旋鈕鎖緊
固定。

For Vibraphone, tighten hand knobs at position (A)
& (C) first ; then hand knob at position (B).

室內型立奏顫音鋁琴則需先確保 (A) 處與 (C) 處
旋鈕可鎖入孔內，再將 (B) 處旋鈕鎖緊固定。

Marimba & Xylophone
立奏低音 / 高音木琴

Marimba &
Xylophone

室內型立奏低音 /
高音木琴

Vibraphone

室內型立奏顫音鋁琴

Vibraphone

立奏顫音鋁琴

A

C

B

P4

Secure keyboard frame to top of leg assemblies
with hand knob. Low (wide) end of keyboard
frame should be over leg identified as low end in
Step 2.

將固定式琴框置於琴架上方，並將固定旋鈕鎖緊。

(Vibraphone only) To attach vibraphone pedal pull rods,
first, loosen the square head bolt of universal head joint
by tuning key, then insert the hex bolt on pedal into
universal head joint, and tighten by tuning key. Make
sure the square head bolt must be locked in the groove
of hex bolt.

( 適用室內型立奏顫音鋁琴 ) 將琴框上制音機構下方的萬

向接頭上的四方頭螺絲用鼓鎖鬆開，將踏板組件上拉桿
上的六方棒插入萬向接頭內，再用鼓鎖鎖緊固定。注意四方頭要鎖入六方棒
上的凹槽內。

When moving vibraphone, must lift and lock the pedal before moving the
instrument, to prevent damage to the pedal and pull rods.

顫音琴在移動時必須將踏板翹起並固定再移動，以免在移動時讓踏板
及拉桿機構受損。

Wing screw for adjustment of pull rod length should be loose so pedal
remains down when hooks are being attached to universal head joint. Once
pull rods are attached, pedal can be set to preferred height and wing screws
tightened to maintain this position.

在將上連接拉桿裝入萬向接頭時，調整上連結拉桿長度使用之蝶螺絲需鬆開，
使踏板維持向下狀態。拉桿確實組好後，即可依需求調整踏板高度，調整完
畢后再將蝶螺絲鎖緊，以固定所需高度。

3

4

5

Set low (wide) end leg assembly upright; then secure crossbar and brace
ends to high (narrow) end leg assemblies as in Step 2.

立起低音側琴架，再將將高音側琴架與連結桿、支撐架同步驟 2 固定並鎖緊。

Lock wheels on leg assemblies by engaging brake mechanism on wheels
on player side. Set low end leg assembly with attached crossbar upright,
then secure crossbar and curved brace to high end leg assembly as in Step 2.

立起琴架時可先鎖上腳輪剎車，以避免琴架任意移動，使組裝更便利。
注意側架上的剎車輪須位在演奏者方向。

P5

Besides the preset pedal weight, user can switch to the other connecting
position for heavier pedal response.

踏板反應力度除原廠預設外，使用者需可依其所好，將拉桿連接是前一
個孔位，使用較重的踩踏反應。

5

6

Resonators are inserted from below. Insert higher register side first (narrow
end), then swing lower register side (wide end) into rubbber notches, seating
arms firmly. Repeat process for second set of resonators.

先將一組共鳴管組由琴框高音側 ( 窄端 ) 下方放入內側橡膠共鳴管固定座，再
將另一端共鳴管放入低音側 ( 寬端 )。重複上述步驟組裝第二組共鳴管。

High (Narrow) End
Marimba & Xylophone
立奏琴高音側 ( 窄端 )

Low (Wide) End
Marimba & Xylophone
立奏琴低音側 ( 寬端 )

Wing screws also need to be loosened for height adjustment of instrument.
Pedal height must be reset after eight adjustment as been made.

進行顫音琴高度調整時，此蝶螺絲亦需鬆開，調整完畢后需重新設定踏
板高度。

High (Narrow) End Vibraphone
顫音鋁琴高音側 ( 窄端 )

Low (Wide) End Vibraphone
顫音鋁琴低音側 ( 寬端 )

−

+

P6

(Vibraphone only) Align rotors of two resonator banks; then loop motor belt
around fan pulley at naturals side, and under security plate.

先將共鳴管活葉調整於相同開闔位置，再將馬達皮帶繞於全音共鳴管活頁皮
帶輪上，並置於固定板下方。

Hold the rotor shaft at Naturals side, then turn the shaft of Accidentals
side, until motor belt fit in the pulley at accidentals side.

用左手扶住已經裝好馬達皮帶的全音共鳴管活頁轉動軸，右手旋轉半音活頁
轉動軸，直至將馬達皮帶旋入半音活頁皮帶輪上。

Tightness of motor belt is adjusted before vibraphone is shipped. Player
can make further adjustments by moving the position of motor up or down.
(By adjusting screws shown in below photos.)

齒形皮帶的鬆緊，出廠前會調整到相對適合的位置。使用者可依自己喜好再
藉由調整馬達上下高低做調整。( 調整如下圖所示之螺絲。)

7

P7

Beginning with Naturals (or C diatonic keyboard), lay tone bars carefully
on frame. Hook string at high (narrow) end of instrument around end bar
posts and begin positioning bars between adjacent bar posts, working
progressively down keyboard towards lowest (largest) bars. Once all bars
are placed, pull excess bar cord through towards low (wide) end, bring bar
cord around end posts and hook springs.

將全音部音板小心放置於琴框上，將音板高音側繩子勾在琴框尾端（窄端）
的定音柱上，再將音板依序排列於琴框上，最後將低音側彈簧扣上並固定於
末端（寬端）。

Repeat process with Accidentals (notes that complete C chromatic scale),
placing tone bars over capped resonators only.

重覆上述步驟組裝半音部音板於裝有塞蓋之共鳴管上方，使音板與共鳴管對
齊。無塞蓋之共鳴管無音板配置。

Height Adjustment — Operate hand crank on side of leg assemblies to
raise or lower as needed. Adjust one end at a time, using imprinted scale
as a guide.

腳架高度調整 轉動側架上的把手，依刻度記號調整至適當高度。

Adjustment range should not exceed 4" per side
without adjusting the other side. Loosen wing
screws on vibraphone pull rods before adjusting
height, as described in Step 5.

每次高度調整勿超過 4"，必須 2 邊輪流調整。
調整室內型立奏顫音鋁琴高度時，同步驟 5 敘
述，請先鬆開上連結拉桿之蝶螺絲。

8

9

10

High (Narrow) End 高音側 (窄端 ) Low (Wide) End 低音側 (寬端 )

Tone Bar Mounting

音板裝置

Mallet Instrument

Ver.201205

www.majestic-percussion.com