RO D U C T S P E C IF I C AT I ON S
3
1-7/8” (810 mm)
1
5-15/16”
(405 mm)
2-3/8”
(60 mm)
5-7/16” (138 mm)
3
9”
(
991 mm)
3
4-9/16”
(
878 mm)
20-3/8”
(518 mm)
39-1/16”
(992 mm)
15/16”
(
23.8 mm)
42”
(
1067 mm)
47”
(
1194 mm)
1-1/4”
(
31.8 mm)
4
7-1/4” (1200 mm)
Minimum Rough Opening Width
Minimum Rough
Opening Depth
1/2”
(
12.7 mm)
5/8”
(15.9 mm)
5/8”
(15.9 mm)
62-7/16”
(1586 mm)
15-1/4”
(387 mm)
44-1/8”
(1121 mm)
44-1/8”
(1121 mm)
21-1/4”
(794 mm)
1
5-3/4”
(
400 mm)
Minimum Rough
Opening Height
1
/2” (12.7 mm)
5/8” (15.9 mm)
1/2” (12.7 mm)
5/8” (15.9 mm)
6-1/2”
(
165 mm)
38-5/8”
(981 mm)
25-1/4”
(641 mm)
P
CDVR47SC7 and CDVT47SC7 Direct Vent
G L A S S V I E W I N G A R E A
39-1/16”W x 20-3/8”H (672 Square Inches)
(992 mm x 518 mm)
S T A N D A R D F E AT U R E S
Unitized black louver assembly
Ember bed burner
Ceramic Fiber logs
Grate
Junction box
Nailing tabs for 1/2” (12.7 mm) and 5/8” (15.9 mm)
F I E L D I N S T A L L E D A C C E S S O R I E S
Firebrick: Tavern Brown
Curved Trim: Black
Medium Trim Kit: Black
Manual Blower and Cord (160cfm): FK-12
Thermostat Blower (160cfm): BLOT
Signature Command Blower (160cfm): BLOTSC (requires purchase of
SCSACM & TSFSC)
Signature Command Remotes & Thermostats: RMSC, TSMSC, TSTSC,
TSFSC, WT)
Signature Command Accessories: A/C Accessory, Module and Command
Center, Wall Mount Kits
Conversion Kits: Natural Gas (CDV42CKNS), LP Gas (CDV42CKPS)
Mesh Screen Glass Cover
Wood Cabinet Surrounds (rear vent models)
Designer Facings (Current 600DVB trim, fronts and filigree panels will fit
the CDV. Doors and door frames do not.)
A Brand of Monessen Hearth Systems Co.
149 Cleveland Drive, Paris, Kentucky 40361
www.majesticproducts.com
HPBA
Hearth, Patio & Barbecue Association
RO D U C T S P E C IF I C AT I ON S
12” (305 mm)
8
” (203 mm)
6
” (152 mm)
2-1/2” (64 mm)
12” (305 mm)
9-1/2” (241 mm)
8-1/2” (216 mm)
6” (152 mm)
Finish Wall
Header
Stud
Standoff
Top of Heat
Exhaust Vent
F
P2285b
Side View
Front View
6” (152 mm)
5” (127 mm)
3” (76 mm)
45°
1” (25 mm)
2-1/2” (64 mm)
1-1/2” (38 mm)
3-1/2” (89 mm)
4-1/2” (114 mm)
Side of Fireplace
Opening
Stud
Wall
FP2286
Combustible
Mate rial A rea
P
CDVR47SC7 and CDVT47SC7 Direct Vent
T E C H N I C A L S P E C I F I C A T I O N S
BTU Input: 24,000 Max, 17,000 Min. (Nat) / 24,000 Max, 18,000 Min. (LP)
Ignition System: Signature Command System (AC w/ battery back up)
Gas Type: Natural Gas or Liquid Propane
Gas Line: 18” (473 mm) Flex line w/ shut off 1/2” (12.7 mm) FPT
Flue Type: 4 x 7 Twist Lock, Flex Vent*
Termination: Dedicated Top or Rear Vent
Min. Height Top Venting Before Elbow: 0”
Horizontal Vent: Maximum 20” (508 mm) straight off rear of unit
Low Voltage Wall Switch Wire: 15' (4.5 m) wire with wall switch and cover
Design Certified: CSA
C L E A R A N C E T O F L U E
Horizontal: 3” (26 mm) Top, 1” (25 mm) bottom and sides**
Vertical: 1” (25 mm) on all sides
C L E A R A N C E T O C O M B U S T I B L E S
Fireplace: 0” clearance to stand offs all sides
Floor of unit to Ceiling: 72” (1.83 m) to combustibles
Firebox Opening to Wall: 6” (152 mm) to combustibles
Hearth Requirement: 0” clearance
E F F I C I E N C Y D A T A
Thermal Efficiency: Up to 80% Nat / 80% LP Up to 80% Nat / 80% LP
AFUE Efficiency: N/A Nat / 63.2% LP N/A
P4 Canada Efficiency: 69.6% Nat / 70.6% LP 56.6% Nat / 65.7% LP
*Simpson Dura-Vent, Selkirk Metalbestos and Metalfab are also approved for vent applications
**When vertical rise is 7-1/2 feet (2.29 m) or higher from base of unit, the horizontal vent
CDVR CDVT
(requires adapter).
clearance to combustibles is 1" (25 mm) all sides.
M A N T E L C L E A R A N C E S
OTE: The combustible area above the facing must not pro-
N
trude more than 3/4” (19 mm) from the facing. If it
oes, it is considered a mantel and must meet the
d
mantel requirements listed here.
To avoid personal injury or property damage, the product described by this brochure must be installed, operated and maintained in strict compliance with the instructions packaged with the product and all applicable building or fire codes. Contact local building or fire officials about restrictions and installation inspection requirements. All photographs and drawings on this brochure are for illustrative purposes only
and are not intended for, nor should they be used as a substitute for the instructions packaged with the unit. Appearance and specifications of the product are subject to change without notice. 12/10 ver.1
MADE IN U.S.A.
A Brand of Monessen Hearth Systems Co.
149 Cleveland Drive, Paris, Kentucky 40361
www.majesticproducts.co m