If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
Or visit our web site 24 hours a day, 7 days a week for product assistance at
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
Tools required: Hex wrench and open wrench (provided).
2
Page 3
ASSEMBLY INSTRUCTIONS
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back
and fully tighten all bolts. This will make the assembly easier.
1. Unpack the units and confirm that you have all hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
C
E
C / D
1
UP
E
1/4" x 5/8” Bolt
(2 used in this step)
①
D
2. Attach the Stretcher (E) between the Legs (C and D) with two 5/8” Bolts (1).
3
Page 4
C
1/4" x 5/8” Bolt
(4 used in this step)
3. Stand the assembled unit upright.
ASSEMBLY INSTRUCTIONS
B
①
D
Lock Washer
(4 used in this step)
②
1
2
3
B
C / D
Flat Washer
(4 used in this step)
③
4. Attach the Top Metal Frame (B) to the Legs (C and D) with four 5/8” Bolts (1) and four Washers (2 and
3).
4
Page 5
ASSEMBLY INSTRUCTIONS
5. Flip last assembly and attach the Top Metal Frame (B) to the Desk Top (A) with eight 5/8” Bolts (1)
and eight Washers (2 and 3).
1/4" x 5/8” Bolt
(8 used in this step)
①
B
A
Lock Washer
(8 used in this step)
②
1
2
3
B
A
Flat Washer
(8 used in this step)
③
5
Page 6
ASSEMBLY INSTRUCTIONS
6. Securely fasten the Casters (F and G) onto the bottom of Legs (C and D). Be sure the Locking Casters
(F) are located on the same short end.
F
F
D
G
G
C
NOTE: Set the brake on the locking casters unless you are moving the desk.
7. Ask for assistance to stand the assembled unit upright and position it at the desired location.
6
Page 7
Care and Maintenance
For everyday cleaning, chrome, brass, aluminum, and painted metal surfaces can be kept looking their best
by wiping with a slightly damp, soft cotton cloth or vacuum cleaner brush.
If soiled, wipe with clean sponge or cloth wrung out of water. Wipe dry with cloth or paper towel to avoid
water spots.
Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the protective
coating.
Metal will rust if the finish is scratched or if your furniture is exposed to excessive humidity, particularly in
salt water locations.
Most metal furniture has a protective coating to prevent rust, however rust may occur if the finish is marred
or wears away over time.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/screws periodically and tighten them if necessary.
Further Advice about Metal Furniture Care
It is best to keep your furniture in a climate controlled environment. Continual exposure to damp and wet
environment can cause corrosion. It is advised to keep furniture away from direct sunlight as it may damage the
finish. Indoor furniture is not recommended for outdoor use.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State
to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
7
Page 8
Page 9
FECHA de COMPRA
: / /
NÚMERO de LOTE:
Escritorio de metal Beckett para niños
Serie # MS18-D2-1011-05
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto
a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
O visite nuestra página de Internet 24 horas al día, 7 días a la semana para asistencia
ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
ENSAMBLE REQUERIDO POR ADULTO
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
www.whalenstyle.com
O mande un correo electrónico a parts@whalenfurniture.com
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2018-02-25 Rev. 0001-A Fábrica: DOTEHA
Page 10
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el
ensamblado.
A- Tapa de escritorio (Cant. 1)
B- Marco de metal superior (Cant. 1)
D- Pata derecha (Cant. 1) E- Soporte (Cant. 1)
C- Pata izquierda (Cant. 1)
F- Rueda con bloqueo (Cant. 2)
G- Rueda s/bloqueo (Cant. 2)
(1) Perno de 1/4" x 5/8” (Cant. 14+1 extra) (2) Arandela de presión (Cant. 12+1 extra)
(3) Arandela plana (Cant. 12+1 extra) Llave hexagonal (Cant. 1) Llave española (Cant. 1)
Herramientas requeridas: Llave hexagonal y llave española(provistas).
2
Page 11
INSTRUCTIVO DE ENSAMBLE
Nota: Por favor no apriete completamente todos los pernos, hasta que termine con el ensamble de las
partes, después asegúrese de apretar todos los pernos, esto hará el ensamble más fácil.
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
Ensamblar la unidad en un piso alfombrado o en un cartón vacío para evitar rasguños.
C
E
UP
C / D
1
Perno de 1/4" x 5/8”
(2
usados en este paso
E
)
①
D
2. Adjuntar el soporte (E) entre las patas (C y D) con 2 pernos de 5/8” (1).
3
Page 12
INSTRUCTIVO DE ENSAMBLE
C
Perno de 1/4" x 5/8”
(4
usados en este paso
①
3.Poner la unidad en posición vertical.
B
)
Arandela de presión
(4
D
usados en este paso
②
)
B
Arandela plana
(4
usados en este paso
1
2
3
C / D
)
③
4. Adjuntar el marco de metal superior (B) a las patas (C y D) con 4 pernos de 5/8” (1) y 4 arandelas (2 y
3).
4
Page 13
INSTRUCTIVO DE ENSAMBLE
5. Voltear el ensamble previo y adjuntar el marco de metal superior (B) a la tapa de escritorio (A) con 8
pernos de 5/8” (1) y 8 arandelas (2 y 3).
Perno de 1/4" x 5/8”
(8
usados en este paso
①
B
A
)
Arandela de presión
(8
usados en este paso
)
②
1
2
3
A
Arandela plana
(8
usados en este paso
B
)
③
5
Page 14
INSTRUCTIVO DE ENSAMBLE
6. Asegurar las ruedas (F y G) a la parte inferior de las patas (C y D). Asegúrese que las ruedas de bloqueo
(F) estén el mismo extremo corto.
F
F
D
G
G
C
NOTA: Poner el freno en las ruedas de bloqueo a menos de que mueva el escritorio.
7. Pedir asistencia para poner la unidad en posición vertical y en el lugar deseado.
6
Page 15
Mantenimiento y Cuidados
Para limpieza diaria, superficies de cromo, de cobre, de aluminio, y de metal pintados se pueden mantener
viéndose bien limpiando con un patio de algodón suave y húmedo o con un cepillo de aspiradora.
Si mojado, limpiar con una esponja limpia o con un paño sacada del agua. Secar con un paño o un papel de
cocina para evitar puntos causados por agua.
No usar abrasivos duros o químicos para limpiar las superficies de metal porque puede dañar la capa
protectora.
El metal se oxidará si el acabado es rayado o si el mueble se expone a humedad excesiva, particularmente
en lugares de agua salada.
La mayoría de los muebles de metal tienen una capa protectora que evita el óxido, de cualquier forma, el
óxido puede aparecer si el acabado se estropea o si se desvanece con el tiempo.
En caso de que su unidad sea manchada o dañado durante el uso le recomendamos hablar a un profesional
para que le ayude.
Revisar los pernos y tornillos periódicamente y apriételos si es necesario.
Más recomendaciones para el cuidado de su Mueble
Es mejor mantener la unidad en un área de clima controlado. Temperatura extrema y cambios de humedad
pueden causar cambios como partes pandas, molduras que se contraigan o que la madera se raje. Es
recomendable mantener la unidad lejos del sol directo ya que puede dañar el acabado.
Cuidados adecuados y limpieza pueden extender la vida útil de su unidad. Siga estas recomendaciones y
mantendrá su mueble en buenas condiciones de uso por muchos años.
Esperamos que disfrute su mueble por muchos años.
¡Gracias por su compra!
GARANTÍA DE CALIDAD
Nosotros estamos seguros que usted se encontrará feliz con la compra de esté producto de Whalen
Furniture.
Si esté producto tiene algun defecto de ensamble o material, o si tiene alguna falla en uso normal, nosotros
lo repararemos o lo re-emplazaremos hasta por un año à partir de la fecha de compra. Todo producto de
Whalen Furniture es diseñado para alcanzar sus expectativas más altas. Nosotros le garantizamos que
inmediatamente podrá ver el valor de nuestra mercancía de la más alta calidad.
Está garantía le proporciona derechos legales específicos y tal vez tenga otros derechos que varían de estado a
estado
.
Servicio al cliente
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
: 866-942-5362
www.whalenstyle.com
7
Page 16
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.