Maimin K-105 User Manual

THS

aJTI'SR'S

SDt:S

70

Kin~treet

¥847-709-2500 ·

MANUAL END CUTTING SYSTEM

Maimin

~

847-709-2599 ·

Technology

Elk

1

Grove

MODEL

Group,

Villager

~

www.maimin.com · email: [e-mail]

Illinois

Inc.

60007

USA

K-105

PARTS AND INSTRUCTIONS BOOK

SERIAL

NUMBER

SfARTING

EFFECTIVE

WITH
12/02

EC15-

OR

fC25-

SAFETY PRECAUTIONS

This instruction manual describes the operation and function
this manual carefully to ensure safe use and maximum performance from your machine.

Failure to follow instructions may lead to injury (cuts, electric shock, burns, fire,
persons). This machine is for commercial use only. Read all instructions before using.

The purchaser must instruct all operators
safety measures and equipment should be provided

cautioned
have qualified operators to instruct new persons, contact MAIMIN directly,
distributor

that·improper

or

representative.

or

careless use

on

the proper use

to

protect the operator. Operators must be

of

this equipment may cause personal injury.

of

a Maimin End Cutting System. Read

or

injury

of

this equipment. All standard industrial

If

or

an authorized

WARNINGS

Danger!

Sharp Blade!
Moving
Electric Connections!

Parts!

to

you do not

Keep hands, fingers, all other bodily parts, clothing and jewelry away from blade and moving parts.
To reduce the risk
To reduce the risk

1.

Use machine only for its intended use

2. Turn machine to

3. Connect this machine to a properly grounded outlet only.

4. Always disconnect electrical connection when not using, servicing,

5. Do not leave machine unattended while it is connected to a power outlet.

6.

Do

not

operate machine with a damaged cord

disassemble; use a qualified serviceman for repairs. Incorrect assembly can cause electric shock when

the machine

7.

Keep hands, fingers, all other bodily parts, clothing and jewelry away from blade and moving
parts.

8.

Keep guards in place and in working order.

9.

The knife key and other wrenches must be removed from the cutting machine before starting

motor.

10.

Keep ventilation openings free from dust and lint.

11.

Keep machine clean and blade sharp for best and safest performance.

of

electric shock, do not install

of

cuts, electric shock, burns, fire,

"OFF"

is

used. 1

(0)

before connecting

or

store this machine in a wet location.

or

injury

or

disconnecting power cord

or

if

machine has sustained damage. Do

to

persons:

See Grounding Instructions.

or

maintaining machine.

not

THESE WARNINGS SHOULD BE POSTED

CLOSE PROXIMITY

IN

A VERY CONSPICUOUS LOCATION IN

TO

THE

MACHINE.

Grounding Instructions

This machine must be grounded.

path

of

least resistance for electric current to reduce the risk

Danger!

qualified electrician or serviceman who
grounding instructions are not completely understood
properly grounded. Disconnect this equipment from electrical power source before proceeding with
any disassembly for adjustment

Use correct wire sizes with this machine.

USA ONLY: 1 phase: Use A

INTERNATIONAL: 1P+N+: Use 3 x 1,0

Improper connection to electric source can result in a risk

3 phase: Use AWG 16/4 SJ,

3P+: Use 4 x 1,0

In

the event

or

repair.

WG

16/3 SJ, SJT

of

malfunction

is

familiar with applicable codes and regulations

or

or

SJE

SIT

or

SJE

mm

CEE (2)

mm

CEE (2)

61

or

breakdown, grounding provides a

of

electric shock.

if

in doubt as

61

of

electric shock. Check with a

to

whether this machine

if

the

General Precautions

• This machine is equipped with a very sharp blade and other moving parts. Leave all guards in
their proper position.

• Always wear safety glasses when operating or servicing this equipment.

• Do

• This equipment includes a cutting machine that is designed

• All personnel should be instructed to stand well clear

•

• We recommend that you take substantial safety measures to avoid any damage in the event a

• Do not open

• Do not use the machine

not

operate until all instructions for this machine have been read.

track. Equipment should be set up with a minimum
rear.

At

startup and during operation, be sure

machine and all components.

problem occurs.

or

modify the machine

than described in the specifications.

or

any

of

its components for the purpose

body.

or

to

monitor the functions and performance

any

of

its components

to

run

at high speed across the

of3

feet

(1

meter) clear path at front and

of

this equipment when in operation.

or

use these in any way other

of

protecting the human

of

the

is

General Maintenance

• ADJUSTING THE SHARPENER: When the blade

stone position by unscrewing the screw for the sharpener arm so as to ensure a correct
distance between the sharpener and the blade edge. After finishing adjustment, tighten the
screw.

• REPLACING THE SHARPENING STONE: Take

unscrewing it. Mount the new Sharpening Stone and tighten it.

• REPLACING THE BLADE:

1.

Remove the Sharpener Assembly (F)

2.

Unscrew the lock nut (G) for the blade.

3.

Remove the blade.

4. Install a new blade, making sure the printed side is face out.

5. Tighten the lock nut (G) for the blade.

6.

After replacing blade, replace the Sharpener Assembly and adjust correctly.

• REPLACING THE

1.

Remove the lower blade arm by unscrewing the screw (H) for the lower blade arm.

2. Replace the lower blade by unscrewing the fixed screw, ensuring that the flat surface
of

the lower blade

• REPLACING THE CARBON BRUSH

1.

Carbon Brush Cap

2.

Always replace right and left Carbon Brushes at the same time.

3.

Be sure to hold metallic part

• CLEANING THE TRACK AND THE MACHINE

1.

Clean the Track with a brush thoroughly after each 10 to 20 hours

2. Take the machine out

brush after each

LOWER

is

adjacent to the blade edge.

(I)

is replaced by turning it left with wrench.

of

30 days

BLADE

of

the Brush. Keep fingers away from Carbon.

the Track and thoroughly clean the L-shaped track with a

of

use.

is

worn out, adjust the sharpening

offthe

Sharpening Stone (EC2626) by

of

use.