Mahlkonig K22S Installation Manual
LADENMÜHLEN | SHOP GRINDER
Operating Instructions
Guatemala (K32S / K22S)
the casual one“
”
The professional art of grinding
since 1924
LADENMÜHLEN | SHOP GRINDER
LADENMÜHLEN | SHOP GRINDER
Table of Contents
1. Safety 4
1.1 Symbols 4
1.2 Safety Instructions 4
1.3 Purpose of Use 5
1.4 User Requirements 5
2. Technical Data 5
3. Description 6
4. Safety Devices 7
5. Set-Up and Basic Adjustment 7
5.1 Setting-up area 7
5.2 Installation 7
5.3 Initial operation 7
6. Operation 8
7. Operating Faults 8
8. Recalibration of the Grind Adjustment 10
9. Cleaning 10
9.1 Cleaning with GRINDZ™ Grinder Cleaner 11
9.2 Cleaning of the Grinder Casing 11
9.3 Cleaning of the Grinding Mechanism 11
10. Maintenance and Repair 12
11. Spare Parts 12
12. Certificate 13
13. Warranty Conditions 13
14. Wiring Diagram 14
3
LADENMÜHLEN | SHOP GRINDER
1. Safety
Please read and observe the following operating instructions carefully. Non-observance can result in
damage to the grinder as well as in health-threatening risks for the user.
1.1 Symbols
The following two symbols are used in this manual of operating instructions:
Safety instruction:
In case of non-observance, extreme risk of accidents
exists.
General instruction:
In case of non-observance, the device can become
damaged or optimum operation not be guaranteed.
1.2 Safety Instructions
The grinder you have purchased is only allowed to be used to grind
whole coffee beans or the unground material for which the grinder has
been set up for. Ground materials are never allowed to be filled into the
hopper.
Do not carry out any modifications or changes on the grinder. In case of
non-observance, the manufacturer shall be liable for resulting damage
in no case whatsoever. your fingers or objects into the rotating grinding
mechanism underneath the hopper.
Always pull the power supply plug out of the outlet before carrying out
any maintenance or cleaning work on the grinder.
Never put the grinder into service with a defective power supply cable.
Check the grinder regularly for any signs of damage on the power supply
cable, plug, finger protector, etc.
Any repairs that may be required are only allowed to be carried out by
experts. Please contact an authorised customer service centre, your local
dealer or us directly as the manufacturer.
Do not exceed the permissible maximum operating period of 40 minutes. Afterwards, allow the motor to cool off for approx. 30–40 minutes.
When unpacking the grinder, please check to determine whether the
power supply voltage (volts) corresponds to the grinder voltage on the
rating plate.
Children do not recognise the risks that may arise when handling electrical grinders; therefore never leave children alone with electrical grinders
without proper supervision.
Never immerse the grinder in water and do not operate it with wet hands.
4
LADENMÜHLEN | SHOP GRINDER
1.3 Purpose
Only cleaned, unground material, for which the Guatemala grinder has
been set up for, is allowed to be ground in the grinder. Never use the
grinding mechanism to grind other products or objects.
1.4 User requirements
No special requirements are specified for the users of this device. It is,
however, assumed that this manual of operating instructions has been
carefully read and understood and that all instructions provided in this
manual will be observed. In addition, working with the grinder on a safety-conscious basis is also expected.
2. Technical Data
Description Guatemala (K32S / K22S)
Voltage/Frequency 220-240V / 50Hz
220V / 60Hz
115V / 60Hz
100V / 50Hz
100V / 60Hz
Rotation
50 Hz 2850 rpm.
60 Hz 3400 rpm.
Sound emission
idle operation 65 dB
operation 85 dB
Pre-fuse 16 A-slow
Overload circuit breaker
230V / 50Hz 7A T
220V / 60Hz 8A T
115V / 60Hz 16A T (incl. in switch)
100V / 50Hz 10A T
100V / 60Hz 16A T (incl. in switch)
max. operating time 40 minutes ON
of the grinder 100 minutes OFF
Dimensions in mm W 220, D 330, H 620
Dimensions in inch W 8.6, D 13.0, H 24.4
Weight 18 kg (39.7 lbs)
Hopper capacity 500 g (1.1 lbs)
(Please ask the manufacturer or dealer for technical data on other voltages and frequencies.)
5
LADENMÜHLEN | SHOP GRINDER
3. Description
The main components and operating elements are shown in the figure.
Pos. 1 Hopper with lid
Pos. 2 Grind adjustment
1
Pos. 3 Spout
Pos. 4 Bag holder
Pos. 5 Tray for residues
Pos. 6 On / Off-Switch
Pos. 7 Reset button for current overload (back)
Pos. 8 Bag holder handle
Pos. 9 Casing with motor and grinding mechanism
9
2
3
4
5
8
7
6
6
Loading...