Page 1
MAHLKÖNIG GmbH & Co. KG
Operating Instructions
K30 ES, K30 Vario, K30 Competition
Page 2
Manual
Dear customer / service personnel
The ”Single Espresso Grinder K30ES ", is a fully automatic
espresso coffee grinder of the proven MAHLKÖNIG quality.
We have developed this product with over 80 years of experience
in the manufacture of coffee grinders assuring you of high quality
grinding of espresso and other types of coffee beans.
Read through and observe the operating instructions, so you and
your customers will thoroughly enjoy the ”K30ES”. Please store
the instructions in a safe place. If anything is unclear or additional
information is required, please contact your authorized dealer or
us as the manufacturer. We will be pleased to advise you further.
We wish you unlimited pleasure and success with our product.
MAHLKÖNIG GmbH & Co. KG
August 2006
Page 3
Inhaltsverzeichnis
1. Safety
1.1 Symbols
1.2 Safety Instructions
1.3 Usage Purpose
1.4 User Requirements
2. Technical Data
3. Description
3.1 Main Components and Operating Elements
4. Safety Devices of the Grinder
5. Set-Up and Basic Adjustment
5.1 Location of Use
5.2 Installation
5.3 Basic Adjustment
6. Operation
6.1 Handling the Grinder
6.2 Display / Menue
6.3 Interruption of Grinding
7. Operating faults
8. Cleaning
8.1 Cleaning with GRINDZ™ Grinder Cleaner
8.2 Cleaning the Grinder Placement Surface
8.3 Cleaning the Grinder Casing
8.4 Cleaning of the Grinding Mechanism
9. Removal of the Integrated Grinder
10. Maintenance and Repair
10.1 Grinding Disc Replacement
10.2 Grinding Fineness Adjustment with the Grinder switched
ON
11. Spare Parts
12. Wiring Diagram
10. Certificate
11. Warranty Conditions
Page 4
1. Safety
Please read carefully and observe the following
safety instructions. Failure to do so can result
in damage to the grinder and endangerment
of the user.
1.1 Symbols
The following two symbols are used in these operating instructions:
Safety Instruction:
Imminent accident danger if you fail to observe.
General Instruction:
Failure to observe can result in damage to
the grinder and optimum operation cannot
be guaranteed.
1.2 Safety Instructions
Only whole roasted coffee beans may be ground in the K30 ES.
When unpacking please inspect whether the power supply
(voltage) complies with the grinder voltage on the manufacturer’s
name plate. Never operate the grinder in damp or wet surroundings.
Always remove the electrical plug from the outlet prior to conducting maintenance or cleaning work on the grinder. Also, prior to
removing the bean container, the plug must be removed from the
electrical outlet.
Never operate a grinder with a damaged electrical cord. Inspect
the grinder regularly for damages of the electrical cord, plug, etc.
Any required repairs may only be conducted by authorized service
personnel. For this reason, please contact a customer service
repair facility, your dealer or us directly as the manufacturer.
Do not exceed the maximum allowable continuous grinding
time of 20 min. Afterwards, allow the grinder to cool off before
the next operation.
Make no modifications or alterations to the grinder. The manufacturer assumes absolutely no liability for damages occurring from
failure to observe these instructions.
Children cannot appreciate the dangers that can exist in the operation of electrical grinders. For this reason, never leave children
unsupervised with electronic appliances such as this grinder.
Never submerge the grinder in water and
never operate with wet hands.
Page 5
1.3 Usage Purpose
Only whole roasted coffee beans may be ground in the K30 ES
grinder. Never use the grinder to grind other products or objects.
1.4 Personnel Requirements
No special requirements are specified for the users of this grinder.
It is nevertheless a prerequisite that the operating instructions
have been carefully read and understood and that all instructions
provided are observed. In addition, safety-conscious operation is
expected.
2. Technical Data
Type K30 ES, K30 Vario
K30 Competition
Voltage/Frequency 230-240V / 50/60Hz
100-115V / 50/60Hz
Rotation
230-240V 1350 rpm
110-115V 1640 rpm
Sound Emission
Idle Operation 65 dB
Operation 85 dB
Pre-Fuse 16 A-slow
Overload Ciruit Breaker
230-240V 4A T
110-115V 7A T
Max. Permissible Running Time S3 20%
e.g.(4sec on / 16 sec off)
of the Grinder (6.sec on; 60sec. off)*
Dimensions in mm W 234, D 325, H554
Weight 14 kg (31 lbs)
Coffee Bean Capacity 1,5 kg (3.3 lbs.)
(Please request technical data for other voltages and frequencies
from the manufacturer or dealer.)
* only for 115V 60Hz
Page 6
3. Description
3.1 Main Components and Operating Elements
The main components and operating elements are pictured in the
illustration.
Pos. 1 Bean container with lid
Pos. 2 Lock screw for bean container
Pos. 3 Grinding fineness adjustment
Pos. 4 Lock screw for grind adjustment lid
Pos. 5 Grind adjustment lid
Pos. 6 Grinding fineness scale
Pos. 7 Display
Pos. 8 Single shot pre-selection button
Pos. 9 Single shot timer
Pos. 10 Double shot pre-selection button
Pos. 11 Double shot timer
Pos. 12 Spout
Pos. 13 Filter support
Pos. 14 Filter support rest
Pos. 15 Fastening screw for filter support rest
Pos. 16 Grinding mechanism
Pos. 17 Drip tray
1
3
7
8
12
15
14
9
2
6
10
13
16
17
11
5
4
Page 7
Pos. 18 Hopper slide
Pos. 19 Main switch
Pos. 20 Trip switch
Pos. 21 Power cable
4. Safety Devices of the Grinder
Thermal overload circuit breaker
The motor of the grinder is protected by a thermal overload circuit
breaker, which interrupts the motor's electric circuit in the event of
electric overload. The trip switch, item 19, must be pressed to
enable the grinder to be re-started.
The user has no influence whatsoever on
this circuit breaker. If the circuit breaker
trips repeatedly, an authorised service
partner must be consulted, as the motor's
winding may be damaged.
18
19
20
21
Page 8
5. Set-up and Basic Adjustment
A grinding test run is carried out on each grinder in the
manufacturer's factory. This is why you may find ground material
residue in the grinding mechanism!
5.1 Usage Location
Place the grinder on a level, vibration-free surface.
Never operate the grinder in moist, or even
worse, in wet surroundings!
5.2 Installation
You have received your grinder in operating condition. Now you
only need to connect it to the mains. Proceed as follows:
Protect your device with separate pre-fuses
(not included in the scope of delivery) according
to the information provided under Point 2 "Tech nical data".
Make sure that the pre-fuse is not overloaded
by other devices (e.g. fan heaters, deep freez ers).
Check whether the mains voltage and frequency
correspond to the information on the rating
plate.
Insert the plug into the corresponding grounded outlet.
5.3 Basic Adjustment
Once the device is ready to operate, a grinding test should be
carried out.
Basic adjustment to a moderately fine setting has been carried out
in the factory using espresso beans. The following markings have
been made on the grinding mechanism (interior):
Red line: Basic adjustment 0, finest setting and minimum
grinding disc spacing
Red line: Basic factory setting and also the position for
installing and removing the lid, in order to
achieve the factory setting after positioning
the lid.
Never rotate the grinding discs clockwise up
to the red mark, as the grinding discs may
otherwise be damaged.
Page 9
6. Operation
Only use the K 30 ES espresso grinder according to the purpose
specified in 1.3.
Observe the safety instructions under 1.2!
Never exceed the maximum permissible continuous operating
period of running time (S3 20% e.g. 4 sec on and 16 sec off); 6 sec
on and 60 sec off only for 115V/60Hz. Do not exceed the
maximum allowable continuous grinding time of 20 min
Afterwards, allow the grinder to cool off before the next operation.
6.1 Handling the Grinder
Proper operation necessitates the steps described in the following:
6.1.1 Actuate the main switch on the rear of the device. Set the
grinding fineness e.g. to 2 ½.* To do this, pull the sliding detent,
item 3, out to the front and turn the lid / grinding fineness adjustment to the left to the 2 ½ mark.
Rotation to the left = fine
Rotation to the right = coarse
6.1.2 Open the bean container. Pour whole, roasted espresso
beans into the bean container from above. Never pour in coffee
powder.
6.1.3 Check whether the hopper slide (item 18) is open.
6.1.4 Adjust the filter support rest (item 14) to your espresso
machine's filter support. Proceed as follows:
Switch the K 30 ES espresso grinder off using the main switch
(item 19). Use the enclosed Allen key to loosen the fastening
screws (item 15) slightly and adjust the height of the filter support
rest.
If the enclosed filter support rest does not
fit, please contact the manufacturer or your
local dealer. We will be happy to send you
a different rest.
Slide the filter support between the filter support mounting and the
filter support rest until it comes to a stop.
Push the filter support rest up and tighten the fastening screws.
The setting is correct when the filter support independently
remains in the mounting.
6.1.5 Check whether the factory grinding time settings for single
S 2.0 and double D 4.0 appear in the display. If the display corresponds to the factory settings, continue as described in point 6.1.9;
if this is not the case, the time must be set (see point 6.1.6).
* not for K30 Vario & K30 Competition
Page 10
6.1.6** Setting the grinding time (portion quantity). Simultane-
ously press both buttons for approx. 3 sec. MENU appears in the
display. Scroll to menu option STI using the single button.
6.1.7** Use the Single shot timer, item 9, to set 2.0 sec. Scroll to
menu option DTI using the single button. Use the Double shot
timer, item 11, to set 4.0 sec.
6.1.8** To store these values, press both buttons simultaneously
until SAVE appears in the display.
6.1.9 Adjust the grinding fineness by pulling the sliding detent out
to the front / turn the adjustment screw*** and turning the lid /
grinding fineness adjustment to the 2 ½ mark. Note that "0" is the
finest setting and "10" is the most coarse setting.
6.1.10 Push your espresso machine's filter support into the filter
support mounting, item 13, until the grinding process is switched
on.
6.1.11 Now make a test portion of espresso using your machine.
If the result is unsatisfactory, repeat adjustment steps 6.1.6 to
8.1.8 again by varying the grinding time and grinding fineness.
Carry out this process until the best coffee results have been
reached.
6.2 Display / Menue
6.2.1 Calling up the menu
To call the menu up, simultaneously press both buttons for
approx. 3 sec. MENU appears in the display. Scroll forwards
using the single button. Scroll backwards using the double shot
button.
6.2.2 Grinding time setting
The grinding time range for single cups and double cups shoud
be set between 0.1 and 10 sec.* Scroll to menu option STI (time
for single cups) using the single button. Use the Single shot timer,
item 9, to set the time. Scroll to menu option DTI (time for double
cups) using the single button. Use the Double shot timer, item 11,
to set the time.
6.2.3 Store the grindig time or go to 6.2.4
To store these values, press both buttons simultaneously until
SAVE appears in the display. You now have a setting range of 0.5
sec.
6.2.4 Quantity indicator
Scroll to menu option S using the single button. The display
shows e.g. S 000020 – You have ground 20 single cup portions.
Scroll to menu option D using the single button. The display
shows e.g. D 000018 – You have ground 18 double cup
portions.
** not for K30ES Competition
***for K30 Vario & K30 Competition
* not for 115V / 60Hz
** not for K30ES Competition
**
Page 11
6.2.5 Continuous quantity indicator
Scroll to menu option SC using the single button. The display
shows e.g. SC 000127 – You have ground 127 single cup
portions.
Scroll to menu option DC using the single button.
The display shows e.g. DC 004037 – You have ground 4037
double cup portions.
If you wish to set the grinding time, proceed from point 6.2.2.
If you would like to exit the menu, press both buttons simultaneously until SAVE appears in the display.
6.2.6 Reset function
If you wish to reset the quantity indicator 6.2.4, switch the grinder
off at the main switch. Press both buttons simultaneously and
switch the main switch on again.
The quantity indicator is now set to 0.
6.3 Interruption of grinding*
If the grinding process is interrupted before the set grinding time
has expired, the light-emitting diode in the active pre-selection
button flashes. The grinding process can be re-started by pushing
the filter support back into the mounting. The missing quantity is
ground into the filter support.
If this is not desired, the pre-selection button can be activated
and the entire set grinding quantity or grinding time is available
once again.
7. Operating faults
Defect
The grinder
hums but does
not grind.
Cause
The spout is
clogged.
Grinding is set
too fine.
A foreign object
is in the grinding
mechanism.
Remedy
Set grinding fineness to
"coarse" and trigger the
grinding process. The grinder
will then grind itself free.
Afterwards, return the setting
to the desired grinding
fineness.
Turn the grinding fineness
setting to the right, to
"coarse", and trigger the
grinding process. The grinder
will then grind itself free.
Afterwards, return the setting
to the desired grinding
fineness.
Clean the grinding mechanism as described and
remove the foreign object.
Observe the safety instructions!
The grinder
does not grind,
the display is lit,
single cup is
pre-selected*
The grinding
time is set to 0.
Reset the grinding time.
* not for K30ES Competition
* not for K30 Competition
Page 12
7. Operating faults
In the case of other malfunctions or continued faults, please
contact your dealer or your authorised customer service
centre.
8. Cleaning
8.1 Cleaning with GRINDZ™ Grinder Cleaner
We recommend cleaning your espresso grinder once a week and
your shop grinder once a month with our GRINDZ™ Grinder
Cleaner.
Simply take the recommended dose (35 - 40g for espresso
grinders and 70-80g for shop grinders) and drop it into an empty
grinder hopper. You can also use the cup of the jar for dosing. A
full cup will yield between 35 - 40 grams.
Adjust machine setting to medium and operate as if grinding
coffee beans. Once complete, we recommend passing twice as
much coffee through to purge any residue.
8.2 Cleaning the Grinder Placement Surface
8.2.1 Pull out the mains plug!
8.2.2 Tilt the grinder to one side and clean the area on which it
stands and the bottom of its base.
8.2.3 Both surfaces must be dry and free of oil and grease.
8.2.4 Replace the grinder
Defect
The grinder
does not
start, the
operating mode
display is not lit.
Cause
The mains plug
is not inserted.
The overload
circuit breaker
has been
tripped.
The pre-fuse has
tripped.
Remedy
Insert the mains plug into the
socket.
Check to determine whether
the trip button of the circuit
breaker has jumped out.
Press the trip button in again
if appropriate. If the circuit
breaker trips repeatedly,
contact your authorised
customer service centre or
dealer.
Check the pre-fuse. Restore
the pre-fuse to its initial state
or replace it. Determine
whether other devices are
connected to this fuse.
Page 13
8.3 Cleaning the Grinder Casing
8.3.1 Clean the outside of the casing from time to time using a
damp cloth.
8.3.2 Observe the safety instructions under 1.2!
Be careful of sharp edges when cleaning.
There is a risk of injury!
8.4 Cleaning of the Grinding Mechanism
Always pull the main plug from the socket
before carrying out maintenance or cleaning
work on the device!
Do not let any foreign objects fall into the
grinding mechanism!
8.4.1 Close the slide on the bean container. Remove the lock
screw Item 2. Turn the base of the bean container to the right so
that the bayonet releases the bean container. Pull the bean
container off upwards.
8.4.2 Remove beans out of the filler neck. Remove the lock screw
Item 4 and turn the grind adjustment lid to the right. The sliding
detent automatically engages in the coarsest setting.
8.4.3 Remove the grind adjustment lid Item 5.
8.4.4 Now you can carefully vacuum out the grinder housing.
Please do not change any grinder settings!
8.4.5 During the reassembly please make sure that the grind
adjustment lid is placed in a way that the 3 engaging cones fit into
the toothing of the grinding disc support. The screw of the grind
adjustment has to be placed over the cut-out in the intermediate
ring.
8.4.6 Lower the grind adjustment lid onto the intermediate ring
and turn to the left. Fasten the lock screw Item 4.
8.4.7 Carry out a grinding and coffee making test. Readjust the
grinding setting if necessary.
9. Removal of the Integrated Grinder
Always pull the main plug from the socket
before carrying out maintenance or cleaning
work on the device!
Observe the safety instructions under 1.2!
Do not let any foreign objects fall into the
Page 14
9.1 Disconnect the main plug. Close and remove the bean
container. Place the grinder on its side and unscrew the fastening
screws. Store the screws and washers in a safe place.
Re-position the grinder on its rubber feet. Proceed as described
in 8.4.2 and 8.4.3.
9.2 Release the motor's plug-in connector. Carefully pull the
integrated grinder out of the casing.
9.3 Carefully vacuum out the grinder casing. Vacuum out the
grinder casing and the integrated grinder's spout, and clean with
a brush. Do not damage any cables!
9.4 Component assembly is carried out in reverse order. To do
this, please note 8.4.5 to 8.4.7
10. Maintenance and Repair
Always pull the mains plug from the socket
before carrying out maintenance or cleaning
work on the device!
Inspect the grinder regularly for damage,
particularly to the electrical cable, plug, etc.
Any required repairs may only be
conducted by authorized specialist person nel. For this reason, please contact a
customer service repair facility, your dealer
or us directly as the manufacturer.
10.1 Grinding Disc Replacement
10.1.1 Grinding disc replacement should only be carried out by
authorised specialists or a customer service centre. "Repair
manual EK9-EK10-EK11 grinding disc replacement and basic
adjustment", article No. 6592, is required for replacing grinding
discs.
10.1.2 Grinding disc replacement may also be carried out using a
replacement (AT) integrated grinder. To do this, order an AT
integrated grinder. On receipt of the AT integrated grinder, remove
your integrated grinder from the K 30 ES according to section 9
and install the AT integrated grinder into the K 30 ES.
Return your old integrated grinder in the packaging.
Page 15
10.2 Grinding fineness adjustment with the grinder switched ON
10.2.1 Set the grinding fineness adjustment to the 0 detent.
10.2.2 Close and remove the bean container.
10.2.3 Remove the remaining beans from the filler shaft and
vacuum out the grinder casing.
10.2.4 Remove the sealing ring from the filler shaft.
10.2.5 Loosen – do not unscrew – the adjusting screws with the
size 2.5 Allen key (article No. 6568).
10.2.6 Insert the adjusting handle into the filler shaft. The
adjusting handle must engage in the slot in the filler shaft's
transverse bar.
10.2.7 Insert the mains plug back into the socket and switch the
grinder on.
10.2.8 Set the double portion grinding time to 10 sec. (see
section 6.2 paragraph 3).
10.2.9 Hold the adjusting handle firmly and push the filter support
into the filter support mounting until the grinder switches on.
10.2.10 Whilst the grinder is running, turn the adjusting handle to
the left until a slight ringing sound becomes audible. Now turn the
adjusting handle slightly to the right until no further ringing sound
can be heard. Switch the mains switch off.
It is important to ensure that no grinding
disk "rattling" can be heard at the finest
setting! Their service life will otherwise
be significantly reduced!
10.2.11 Disconnect the mains plug from the socket.
10.2.12 Tighten the adjusting screws and remove the adjusting
handle from the filler shaft.
10.2.13 Insert the sealing ring again. If the sealing ring is
damaged, it must be replaced.
10.2.14 Replace the bean container and allow it to engage in the
bayonet and replace the lock screw (item 2). Open the hopper
slide.
10.2.15 Insert the mains plug into the socket and switch the
grinder on using the mains switch.
10.2.16 Reset the desired double portion grinding fineness and
grinding time.
10.2.17 Push your espresso machine's filter support into the filter
support mounting, item 14, until the grinding process is switched
on.
10.2.18 Only remove the filter support once the grinding process
has been completed.
Page 16
10.2.19 Now make a test portion of espresso using your
machine. If the result is unsatisfactory, repeat the adjustment
steps as described in section 6.1.6 to 6.1.8, by varying the
grinding time and grinding fineness.
11. Spare Parts
Spare parts are usually ordered from your customer service
centre or your local dealer. To ensure quick, correct processing of
your order, the following information is absolutely essential:
1. Type designation, serial number and voltage of the
grinder (on the rating plate on the rear of the grinder).
2. An exact description of the part to be replaced or the
article number.
Page 17
12. Wireing Diagram 200-230V 50/60Hz, 240V/50Hz
Page 18
12. Wireing Diagram 100-115V 50/60Hz
Page 19
13. Certificate 14. Warranty Conditions
1. The warranty period is 1 year from the date of purchase.
2. The warranty covers all damages that can be attributed to
inferior materials or defective workmanship. Corresponding
grinders will be repaired or replaced free-of-charge, with the
exception of transport or freight charges. Transport is the
responsibility of the customer. Therefore, avoid damages
with all returns by correct packing.
3. The grinder may only be opened for cleaning purposes in
accordance with the Operating Instructions.
4. This warranty does not cover damages which have
occurred through: Improper usage, improper maintenance,
lack of servicing, usage for purposes other than those
intended, incorrect installation, incorrect voltage, breakage,
natural wear or for reasons beyond our sphere of influence.
5. In order to maintain the warranty, only original spare parts
and accessory parts may be used.
6. Observe in addition our General Delivery Conditions in
their respective current version.
7. The manufacturer is in no way liable for consecutive or
secondary damages.
8. The warranty does not cover costs emerging from repairs
conducted by non-authorized personnel.
Page 20
Manufacturer Name Plate
MAHLKÖNIG GmbH & Co. KG
Tilsiter Straße 142
D- 22047 Hamburg, Germany
Tel.: 040 / 69 69 40-0
Fax: 040 / 69 39 721
office@mahlkoenig.de ; www.mahlkoenig.de
August 2006
Subject to change without prior notice!!
Loading...