SL08_Rev01 Work Instruction Template Template Released 8 November 2018
Work Instruction: Install Rear Seat (Forward Facing)
Rear Seat Kit (P/N 2402AUA00101N)
W O R K I N S T R U C T I O N O V E R V I E W
l
DO NOT ATTEMPT THIS PROCEDURE IF YOU DO NOT
HAVE PROPER TOOLS, TRAINING, AND FACILITIES.
l
Never consider using a two-post lift that is not certified
according to ANSI/ALI ALCTV-2011 or ANSI/UL 201.
(autolift.org)
l
Read and follow all instructions provided when installing
this product. Failure to do so may result in placing
occupants at risk of serious injury or death.
l
To protect bystanders and the service technician(s), shut
vehicle off, remove the Ignition Key and secure vehicle to
prevent unintended movement.
l
Never operate the vehicle in excess of manufacturer’s
specifications.
T OO LS R E Q U I R E D
o
11/16" Wrench
o
5/8" Socket
o
3 mm Drill
o
12 mm Drill
o
Dead Blow Hammer
o
Drill Motor
o
Protective Eye-wear
o
Razor Knife / Chisel
o
Round Pry Bar
o
Socket Driver / Extension
o
Tape Measure
o
Torque Wrench (N•m)
Kit
Component
Description Qty
Hex Bolt - 7/16 - 20 - 1.0" 4
Hex Bolt - 7/16 - 20 - 2.0" 4
Hex Lock Nut - 7/16 - 20 20
Flat Washer - 0.48 x 0.96 x 0.08 20
I N S T A L L A T I O N P R O C E D U R E
1. Place Rear Seat Bottom into rear cargo area and between
rear wheel wells of the ROXOR.
T OR Q U E S P E C I F I C A T I O N
Tighten all fasteners to the torque specification below:
l 7/16 Fasteners –54 N•m (±5.0) - 40 ft lb (±4.0)
R E A R S E A T K I T
Part Number - 2402AUA00101N
Kit
Component
Rear Seat Bottom
PN - 2402AUA00090N
Rear Seat Back
PN - 2402AUA00080N
"L" Brackets 4
Hex Bolt - 7/16 - 20 - 1.25" 12
Description Qty
2. Adjust and measure distance (340 mm) from back of Rear
Seat Bottom mounting brackets to back edge of rear cargo
area. Both sides must be equal.
1
1
CONFIDENTIALDOCUMENT
© 2019 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, I nc.
Page 1 of 4
SL08_Rev01 Work Instruction T emplate Template Released 8 November 2018
Work Instruction: Install Rear Seat (Forward Facing)
Rear Seat Kit (P/N 2402AUA00101N)
3. Using a grease pencil (or similar) mark areas of sealer for
skiving, then mark (4) drill location using mounting brackets
as templates under seat bottom.
4. Remove Rear Seat Bottom, then using a razor knife or
chisel, skive out high spots in sealer that will prevent Rear
Seat Bottom mounting brackets from sitting flat on rear cargo
floor.
To prevent premature rusting of the
body, apply paint or other suitable rust inhibitor to any bare
metal exposed during this installation.
6. Open up (4) holes to 12 mm.
7. Re-install Rear Seat Bottom, then use (4) bolts, (4) lock nuts
and (4) washers to secure seat bottom to rear cargo floor.
Bolt head and washers on top, lock nuts below.
do not over tighten rear (2) fasteners at
this point to allow movement in brackets when installing
Rear Seat Back.
5. Center punch and drill (4) 3 mm pilot holes at marked
locations in rear cargo floor.
CONFIDENTIALDOCUMENT
© 2019 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, I nc.
8. Install Rear Seat Back by sliding (2)square Seat Back
extension brackets down into Rear Seat Bottom mounting
brackets.
use a dead blow hammer if necessary
to help spread seat bottom brackets to accept the seat
back extension brackets.
Page 2 of 4
SL08_Rev01 Work Instruction T emplate Template Released 8 November 2018
Work Instruction: Install Rear Seat (Forward Facing)
Rear Seat Kit (P/N 2402AUA00101N)
9. Torque all Rear Seat Bottom fasteners to specifications.
10. Align an "L" Bracket with Rear Seat Bottom mounting bracket
holes at each corner, and skive out any sealer preventing
the "L" brackets from sitting flat against inner wheel wells.
13. Open up (8) holes to 12 mm.
14. Install (2) front "L" Brackets using (8) bolts, (8) lock nuts and
(8) washers to secure front of seat bottom to wheel wells.
11. Using a grease pencil (or similar) mark (2) drill location at
each corner using "L" Bracket as template.
12. Center punch and drill (8) 3 mm pilot holes at marked
locations on inner wheel wells.
15. Torque (8) front "L" Bracket fasteners to specifications.
16. Install (2) rear "L" Brackets using (4) longer bolts, (4) lock
nuts and (4) washers to secure Rear Seat Back to Rear Seat
Bottom and torque to specifications.
CONFIDENTIALDOCUMENT
© 2019 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, I nc.
Page 3 of 4
SL08_Rev01 Work Instruction T emplate Template Released 8 November 2018
Work Instruction: Install Rear Seat (Forward Facing)
Rear Seat Kit (P/N 2402AUA00101N)
17. Secure (2) rear "L" Brackets to wheel wells using (4) bolts,
(4) lock nuts and (4) washers and torque to specifications.
CONFIDENTIALDOCUMENT
© 2019 Mahindra Vehicle Sales and Service, Inc. All Rights Reserved.
ROXOR is a registered trademark of Mahindra Vehicle Sales and Service, I nc.
Page 4 of 4
Loading...