MAHA AXPLAY PMS 3/R, AXPLAY PMS 3.5, AXPLAY PMS 3/D, AXPLAY PMS 3/X, AXPLAY PMS 3/XL Original Operating Instructions
...
Fehler! Verwenden Sie die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie
die Registerkarte 'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.Fehler! Verwenden Sie die Registerkarte
'Start', um Name dem Text zuzuweisen, der hier angezeigt werden soll.
PMS | LMS
Axle Play Detector
Original Operating Instructions
BA010101-en
PMS 3.5
LMS 20.0
PMS 3/D
PMS 3/R
PMS 3/X
PMS 3/XL
PMS 3/D PIT
PMS 3/P PIT
LMS 18/1 MTL
LMS 18/2 MTL
2
Manufacturer
Service
BA010101-en
2019-09-10
© MAHA Maschinenbau Haldenwang GmbH & Co. KG
The reproduction, distribution and utilization of this document as well as the communication of its contents to
others without explicit authorization is prohibited. Offenders will be held liable for the payment of damages. All
rights reserved in the event of the grant of a patent, utility model or design.
The contents of this edition have been checked with great care. However, errors cannot be fully excluded. Subject to technical change without notice.
MAHA Maschinenbau Haldenwang GmbH & Co. KG
Hoyen 20
87490 Haldenwang
Germany
Phone: +49 8374 585 0
Fax: +49 8374 585 590
Mail: maha@maha.de
Web: www.maha.de
MAHA SERVICE CENTER
Maybachstraße 8
87437 Kempten
Germany
Phone: +49 8374 585 100
Fax: +49 8374 585 491
Mail: service@maha.
de
Web: www.mahaservicecenter.de
BA010101-en
3
Contents
1
Safety .................................................................................................................... 5
2
Specifications......................................................................................................... 9
3
Transport and Storage ......................................................................................... 11
4
Installation and Initial Operation............................................................................. 11
5
Operation ............................................................................................................. 12
6
Maintenance ........................................................................................................ 16
7
Dismantling .......................................................................................................... 23
8
Disposal ............................................................................................................... 23
9
Contents of the Declaration of Conformity ............................................................. 23
1.1 Introduction .............................................................................................................. 5
1.2 Symbols and Signal Words ...................................................................................... 5
1.2.1 Personal Injury .......................................................................................................... 5
1.2.2 Property Damage ..................................................................................................... 5
1.2.3 Information ............................................................................................................... 5
1.3 Intended Use ........................................................................................................... 6
1.4 Requirements on Operating and Service Personnel .................................................. 6
1.5 Safety Instructions for Commissioning ...................................................................... 6
1.6 Safety Instructions for Operation............................................................................... 6
1.7 Safety Instructions for Servicing ................................................................................ 7
1.8 Safety Instructions for Handling Hydraulic Fluid ......................................................... 8
2.1 PMS Specifications .................................................................................................. 9
2.2 LMS Specifications ................................................................................................. 10
5.1 Main Switch ........................................................................................................... 12
5.2 Preparing for Operation .......................................................................................... 12
5.3 Operating the Axle Play Detector ............................................................................ 13
5.4 Operating the Cable Hand Lamp ............................................................................ 14
5.5 Operating the Radio Hand Lamp RHL (Option) ....................................................... 14
5.6 Service Mode ......................................................................................................... 15
5.7 Operating Diagrams ............................................................................................... 15
6.1 Maintenance Schedule ........................................................................................... 16
6.2 Annual Inspection ................................................................................................... 16
6.3 Maintenance by the Operator ................................................................................. 17
6.4 Greasing Points ...................................................................................................... 17
6.5 Care Instructions .................................................................................................... 19
6.6 Spare Parts ............................................................................................................ 19
6.7 PMS Variants for Installation on Lift Runways ......................................................... 19
BA010101-en
4
10
Annex: Operating Diagrams .................................................................................. 23
BA010101-en
5
1
Safety
1.1
Introduction
1.2
Symbols and Signal Words
1.2.1
Personal Injury
DANGER
WARNING
CAUTION
1.2.2
Property Damage
NOTICE
1.2.3
Information
Thoroughly read this manual before operating the equipment and comply with the
instructions. Always display the manual in a conspicuous location.
Personal injury and property damage incurred due to non-compliance with these
safety instructions are not covered by the product liability regulations.
indicates an immediate hazard which, if not avoided, will result in death or severe
personal injury.
indicates a potential hazard which, if not avoided, could result in death or severe
personal injury.
indicates a potential hazard which, if not avoided, could result in moderate or minor personal injury.
indicates a potentially harmful situation which, if not avoided, could result in damage to the equipment or surrounding objects.
indicates important information notes.
BA010101-en
6
1.3
Intended Use
WARNING
1.4
Requirements on Operating and Service Personnel
WARNING
1.5
Safety Instructions for Commissioning
WARNING
1.6
Safety Instructions for Operation
WARNING
• Before pressing the transmit button, check whether the channel of the radio
This device is used exclusively to inspect the axle and joint play of vehicles.
Axle play detectors in mobile test lanes are only intended for operation when the
lifting device is lowered.
The unit must not be modified without express written permission from the
manufacturer. Non-compliance invalidates the declaration of conformity.
Any use other than described is inappropriate.
All persons employed in the operation, maintenance, installation, removal and disposal of the device must
• be at least 18 years old,
• be mentally and physically suited for these activities,
• be demonstrably trained and instructed in writing,
• have read and understood the operating instructions, especially the instructions
what to do in the event of defects or malfunctions,
• be on record as having been instructed in safety guidelines,
• have practical experience in working with vehicle lifts and the hazards inherent
in such equipment.
• The equipment shall be installed and commissioned by authorised service per-
sonnel only.
• Observe the detailed operating instructions.
• Comply with legal accident prevention regulations.
• The permissible load capacity according to the rating plate must not be ex-
ceeded.
BA010101-en
7
hand lamp matches the receiver’s channel. No equipment that might also re-
1.7
Safety Instructions for Servicing
WARNING
Ensure that ecologically harmful substances are disposed of only in accordance
spond to this channel may be located anywhere on the premises. The unintended operation of other equipment may put people at risk.
Furthermore, no transmission equipment that could respond to the axle play
detector may be located anywhere on the premises.
• To prevent injuries caused by impact or being run over, a sufficient safe dis-
tance from the vehicle to be tested must be maintained when it is being driven
onto and off the test equipment.
• Before testing, the vehicle to be tested must be secured against rolling away.
When used on sloped surfaces (e.g. access ramps in mobile test lanes), it is
advisable to have someone man the driver’s cab during testing so they can respond to unintended movements.
• Wear personal protective equipment.
• A sufficient safety distance from the surface of the test plates’ movement area
must be maintained. Risk of crushing and shearing!
• Test plates must not be walked on, even when not in use. There is a risk of fall-
ing due to unexpected test plate movements. There is a risk of slipping due to
water or ice on the test plates.
• During operation avoid lateral shifting of the vehicle on the test plates and con-
tinually monitor the position of both wheels on the test plates. Should the
wheels move close to the edge of the test plates, stop the test immediately and
reposition the vehicle.
• Periodically check the fastening screws of the test plates for tight fit.
• Service work may be done by authorised service technicians only.
• Turn off and padlock the main switch before doing any repair, maintenance or
setup work.
• Work on the electrical equipment may be done by service technicians or certi-
fied electricians only.
•
with the appropriate regulations.
BA010101-en
8
1.8
Safety Instructions for Handling Hydraulic Fluid
CAUTION
• Neutralize hydraulic fluid spills with binder.
• Remove contaminated clothing immediately.
• Inhalation: If symptoms persist, seek medical treatment.
• Skin contact: Wash skin immediately with soap and water. If skin irritation per-
sists, seek immediate medical advice.
• Eye contact: Rinse thoroughly with water and seek medical advice.
• Ingestion: Do not induce vomiting. Seek immediate medical attention.
BA010101-en
9
2
Specifications
2.1
PMS Specifications
PMS 3.5
PMS 3/D PIT
PMS 3.5
Double
PMS 3/P PIT
PMS 3/X
PMS 3/XL
Axle load max.
Wheel load max.
TP Dimensions
Installation height incl.
TP
TP height above floor
Thrust per side max.
Movement per side
max.
TP speed (2 TP simultaneously)
Hydraulic pressure
max.
Pneumatic pressure
max.
Hydraulic fluid
Filling quantity of hydraulic unit
Supply voltage
Rated motor power
Fuse
Control voltage of cable
hand lamp
3500 kg 3500 kg 2800 kg 3500 kg 3500 kg
1750 kg 1750 kg 1400 kg 1750 kg 1750 kg
248x550 mm
(left, ApS)
155x460 mm
(left, ExS)
500x550 mm
(right)
625x625 mm
625x625 mm
(FA)
1310x625 mm
(RA)
248x550 mm
(left, 2x)
426x560 mm
500x550 mm
(right)
127.5 mm
(left)
127.5 mm
(left)
148 mm 148 mm 185 mm
92.5 mm
(right)
92.5 mm
(right)
15 mm 15 mm 10 mm --- ---
11 kN 11 kN 10 kN 11 kN 11 kN
100 mm 100 mm 24° 77 mm 77 mm
75 mm 75 mm --- adjustable adjustable
120 bar 120 bar --- 120 bar 120 bar
--- --- 10 bar --- ---
HLPD 32 HLPD 32 --- see Lift see Lift
8.5 ℓ 8.5 ℓ --- see Lift see Lift
3x400 V 3x400 V --- see Lift see Lift
Abbr.: TP = Test Plate(s); FA = Front Axle; RA = Rear Axle;
ApS = Approach Side; ExS = Exit Side
2.5 kW 2.5 kW --- see Lift see Lift
16 A slow 16 A slow --- see Lift see Lift
24 V 24 V --- 24 V 24 V
BA010101-en
10
2.2
LMS Specifications
LMS 20.0
LMS 20.0
flush-floor
LMS 20.0 ex-
tended TP
LMS 18/1 MTL
LMS 18/2 MTL
Axle load max.
Wheel load max.
TP Dimensions
Installation height incl. TP
TP height above floor
Thrust per side max.
Movement per side max.
TP speed (2 TP simultaneously)
Hydraulic pressure max.
Hydraulic fluid
Filling quantity of hydraulic unit
Supply voltage
Rated motor power
Fuse
Control voltage of cable hand
lamp
20 000 kg 20 000 kg 20 000 kg 18 000 kg
10 000 kg 10 000 kg 10 000 kg 9000 kg
740x740 mm 740x740 mm 1310x740 mm 712x712 mm
232 mm 232 mm 232 mm 170 mm
15 mm 0 mm 15 mm 20 mm
30 kN 30 kN 30 kN 30 kN
100 mm 100 mm 100 mm 100 mm
60 mm/s 60 mm/s 60 mm/s 30 mm/s
120 bar 120 bar 120 bar 120 bar
Abbr.: TP = Test Plate(s)
HLPD 32 HLPD 32 HLPD 32 HLPD 32
20.3 ℓ 20.3 ℓ 20.3 ℓ 8.5 ℓ
3x400 V 3x400 V 3x400 V 3x400 V
2.5 kW 2.5 kW 2.5 kW 2.5 kW
16 A slow 16 A slow 16 A slow 16 A slow
24 V 24 V 24 V ---
BA010101-en
11
3
Transport and Storage
NOTICE
4
Installation and Initial Operation
WARNING
WARNING
Check package to ensure it is complete, in accordance with the order confirmation. Report any transport damage to the carrier immediately.
During loading, unloading and transport always use suitable lifting equipment, material handling equipment (e.g. cranes, forklifts, etc.) and the right load handling
attachments and slings. Always ensure that the parts to be transported are suspended or loaded properly so that they cannot fall, taking into account size,
weight and the centre of gravity.
Store the packages in a covered area, protected from direct sunlight, at a low
humidity and with temperatures between 0...+40 °C (32…104 °F). Do not stack
packages.
When unpacking, take care to avoid any possibility of injury or damage. Keep at a
safe distance when opening the package strapping, do not allow any parts to fall
out.
Installation and initial operation of the equipment may be done only by authorized
and trained service technicians provided by the manufacturer, licensed dealers or
service partners.
Before connecting the power supply, make sure that an external, lockable EMERGENCY-STOP MAIN SWITCH is used. This must be provided by the customer
and installed in the power supply line to the control.
The EMERGENCY-STOP MAIN SWITCH must meet the requirements of
EN ISO 13850.
BA010101-en
12
5
Operation
5.1
Main Switch
DANGER
Main switch in position 0
Main switch in position 1
5.2
Preparing for Operation
WARNING
The main switch is used as emergency switch. In case of emergency immediately
turn it to position 0!
Lift is disconnected from power supply
Lift is ready for operation
Examine the danger zone and ensure that warnings are legible. Damaged or illegible warnings and markings must be replaced immediately.
When operating an axle play detector in a mobile test lane, it must be ensured that
all the hydraulic components’ covers are fitted and do not show any signs of
damage that would restrict functionality or signs of poor attachment.
If light conditions vary a great deal between test objects and peripherals (e.g.
when used in mobile test lanes outdoors), sufficient lighting or glare protection
must be provided.
A sufficiently ergonomic positioning option must be provided for performing the
test (particularly for vehicle testing in mobile test lanes).
• Test plates must not be walked on, even when not in use. There is a risk of fall-
ing due to unexpected test plate movements. There is a risk of slipping due to
water or ice on the test plates.
• During operation avoid lateral shifting of the vehicle on the test plates and con-
BA010101-en
tinually monitor the position of both wheels on the test plates. Should the
wheels move close to the edge of the test plates, stop the test immediately and
reposition the vehicle.
13
5.3
Operating the Axle Play Detector
WARNING
NOTICE
• The hand lamp must be carried in such a way that eliminates the risk of unin-
tentional operation of the axle play detector. For safety reasons, it is advisable
to stay within the axle play detector’s field of vision and danger zone when using the hand lamp.
• The hydraulic unit must never be left running for longer than absolutely neces-
sary, as the pump can become damaged otherwise.
• The hand lamp must be protected against shocks to ensure that the light bulb
has a long service life.
• Some types of axle play detector are equipped with a synchronisation switch
on the control box which enables control of the plates’ lengthwise and/or
crosswise movement.
• If the plates are moved back and forth in the direction of travel, the brake must
be applied as the turning wheels would otherwise follow the plates’ movements.
• Attempts should always be made to cause the vehicle wheel to slip onto the
plates, as this is the best way to detect incorrect axle play.
1 Switch the test device on at the main switch.
2 Drive the vehicle to be tested onto the test plates at walking speed and secure
it against rolling away, e.g. apply the parking brake or use chocks.
3 The testing plates can be operated using the hand lamp’s push-button
functions.
4 Switch the light and the hydraulic unit off after testing.
5 Drive the vehicle off the test plates.
6 Place the hand lamp in the charging holder to charge.
BA010101-en
14
5.4
Operating the Cable Hand Lamp
5.5
Operating the Radio Hand Lamp RHL (Option)
A B C D E
A / B Movement of test plates
C / E Selection of movement (such as switch-over between single, synchronous,
counter or diagonal movement)
D Switch on and off the lamp
See separate operating manual.
BA010101-en
15
5.6
Service Mode
Enable Service Mode
Function while Service Mode is Enabled
Quit Service Mode
5.7
Operating Diagrams
To remove the sliding plates, the hydraulic cylinders must be pressure relieved. To
do this, a Service mode was integrated. When this mode is enabled, only the
valves are driven as in the normal operating mode. The hydraulic pump remains
OFF.
• Cable hand lamp: Push and hold rocker buttons A and B together for
10 seconds. The pump switches off. (Simultaneous actuation of A1 and B1 or
A2 and B2).
Once the second button is detected, the valves are switched off. The pump
remains ON until 10 seconds have elapsed. The plates remain in their last posi-
tion.
• Radio hand lamp: Set to mode LED ON (Manual operating button). To enable
the Service mode, push and hold the operating button for 25 seconds.
During this time period, the valve is ON and the pump is also ON. After
25 seconds the pump switches OFF. The valve remains ON.
When in the Service mode, the valves of the corresponding moving directions can
be driven using the operating buttons, and the plates can be moved by hand.
On the MAH CAN RP circuit board the Service mode is indicated by the yellow
LED of VD20.
• Cable hand lamp: Push and hold rocker buttons A and B together for
10 seconds. The output for the pump switches ON and the Service mode is
quit.
• Radio hand lamp: Set to mode LED ON. Push and hold the operating button
for 25 seconds to quit the Service mode. After 25 seconds the pump switches
ON.
Alternatively, the Service mode can be quit by switching off the power supply.
See Annex.
BA010101-en
16
6
Maintenance
DANGER
Risk of death or severe personal injury by electric shock
6.1
Maintenance Schedule
and aging,
6.2
Annual Inspection
12 (twelve) months
Before doing any maintenance work, turn off the main switch and protect it
against tampering.
Interval Maintenance Items Procedure
Check fluid level, refill if necessary.
Check hydraulic system for leakages.
3 months Hydraulic system
Check power unit for unusual noise during operation, check fastening screws
for tight fit.
6 months Hydraulic fluid
Check fluid for contamination
replace if necessary.
12 months General inspection Check all components for damage.
6 years Pressure hoses Replace pressure hoses
• The maintenance interval prescribed by the manufacturer is
.
This maintenance interval refers to normal workshop usage. If the equipment is
used more frequently or under severe operating conditions (e.g. outdoors), the
interval must be reduced accordingly.
• Maintenance work shall be done only by authorized and trained service techni-
cians provided by the manufacturer, licensed dealers or service partners.
• In case of non-compliance the manufacturer's warranty becomes void.
BA010101-en
17
6.3
Maintenance by the Operator
NOTICE
6.4
Greasing Points
Relieve the pressure to remove the test plates; activate service mode for this purpose (see section “Operation > Service Mode”).
• Remove the test plates and lubricate the guides with a grease gun or grease
the plastic sliding strips every 200 operating hours, but at least every three
months. In the case of PMS plates installed in lift runways, lubrication can take
place directly from below.
• Check that all the guide rods are secure and tighten them if necessary.
• Check the oil level regularly and top it up if necessary. The oil level must be be-
tween the two marks.
• Change the hydraulic oil every two years. Please see the section entitled “Spec-
ifications” for the filling quantity and specifications.
Lubricating with
a grease gun
PMS plates in lift runways (view: underside of the runways)
Greasing with a brush
BA010101-en
18
PMS 3.5
LMS 20.0
LMS 18/1 MTL
LMS 18/2 MTL
BA010101-en
19
6.5
Care Instructions
NOTICE
6.6
Spare Parts
6.7
PMS Variants for Installation on Lift Runways
PMS 3/R
Regular care and maintenance is the key condition for functionality and long life
expectancy of the equipment.
• Periodically clean the equipment and treat it with a care product.
• Repair damage to the paintwork immediately to prevent corrosion.
• Do not use caustic cleaning agents or high pressure and steam jet cleaners to
avoid equipment damage.
To ensure safe and reliable operation, only use original spare parts supplied by the
equipment manufacturer.
BA010101-en
20
PMS 3X or PMS 3XL
Prism
PMS 3X
Available with a
pneumatic prism
as an option =
PMS 3XL
B18, B23, B30, B31 for centring in the 10 t option.
The front axle is centred first of all, followed by the rear axle.
Optional:
PMS 3D
BA010101-en
21
Prism
PMS 3X
Available with a
pneumatic prism
as an option=
PMS 3XL
Optional:
PMS 3R
BA010101-en
22
PMS 3P (Pneumatic)
PMS 3XIE
Prism
Prism
PMS 3P
Standard:
test plate on the
left and right
ATL:
one plate on the
right in the direction of travel only
PMS 3XIE
With two pneu-
matic prisms
BA010101-en
23
7
Dismantling
8
Disposal
9
Contents of the Declaration of Conformity
MAHA Maschinenbau Haldenwang GmbH & Co. KG
Type:
Name:
Directives:
Standards:
10
Annex: Operating Diagrams
Decommissioning and dismantling of the equipment may be done only by
specially authorized and trained personnel provided by the manufacturer, licensed
dealers or service partners.
Pay attention to the product and safety data sheets of the lubricant used. Avoid
damage to the environment. Should a disposal of the device be necessary it must
be done in adherence with locally applicable legal regulations regarding
environmental protection. Remove all materials properly sorted out and bring them
to a suitable waste disposal service. Collect operating materials such as grease,
oils, coolant, solvent-based cleaning fluids etc. in suitable containers and dispose
of in an environmentally protective manner.
Alternatively, you may take the equipment to a specialised waste management
plant to ensure that all components and operating liquids are properly disposed
of.
herewith declares as a manufacturer its sole responsibility to ensure that the
product named hereafter meets the safety and health regulations both in design
and construction required by the EC directives stated below.
This declaration becomes void if any change is made to the product that was not
discussed and approved by named company beforehand.
PMS / LMS
3,500 / 20,000 kg
EN 61000-6-3, EN 61000-6-2
See following page(s).
Axle clearance tester for cars and lorries; permissible axle load
2006/42/EC; 2014/30/EU
EN 12100-1/-2; EN 13850, EN 13857, EN 349; EN 60204-1;
BA010101-en
A
87
B
C
A2
B2
C2
D
D0
E0
E
LMS 18/2 MTL
300
Büro
100075
F
10
von
1
Blatt
--
Version
A3
87
D0
/
I 0 II
I 0 II
I 0 II
- 0
- 0
Werkstoff
Werkstoffnummer
Änderungsnr.
D1
light on/off
Licht an/aus
Fluid-Plan
right plate
/
left plate
linke Platte / rechte Platte
cable hand lamp
Kabelhandlampe
A2
A1 -
B2
B1
A1
B1
C1
D1
E1
[1/8] PMS 3.5 & LMS 20.0 &
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
Dokumentnummer
10001022
00
Nettogewicht in kg
Maßstab
E
Schutzvermerk beachten
DIN ISO 2768-mK
nach DIN ISO 16016
0.000
1:1
Benennung
Revision
Fernbedienung PMS/LMS Bedienschema
3000007
Materialnummer
alte Materialnummer
MOBERMAY
Datum, Freigabe
02.09.2019
6
MOBERMAY
Datum, Prüfer
02.09.2019
MOBERMAY
5 6
LED off
/
LED off
/
Size ISO 14405
Allgemeintoleranzen
4
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
5
Datum, Ersteller
3.6.2019
4
32
right plate
/
left plate
linke Platte / rechte Platte
2 3
radio hand lamp
Funkhandlampe
1
A
Mode
LED off
Mode
LED off
/
/
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
B
C
D
E
F
A
10
von
2
Blatt
F
A3
B
C
A2
B2
C2
D0
D
E0
E
300
Büro
87
Werkstoff
Werkstoffnummer
D0
/
I 0 II
I 0 II
I 0 II
- 0
LMS 18/1 MTL
- 0
100075
Änderungsnr.
--
Version
87
D1
light on/off
Licht an/aus
Fluid-Plan
A1
B1
C1
D1
E1
[2] LMS 20.0 ZA &
alte Materialnummer
MOBERMAY
10001022
00
Datum, Freigabe
02.09.2019
6
right plate
/
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
0.000
Dokumentnummer
Revision
Nettogewicht in kg
MOBERMAY
left plate
linke Platte / rechte Platte
cable hand lamp
A2
Kabelhandlampe
A1 -
5 6
4
B2
B1
LED off
/
E
Size ISO 14405
LED off
/
nach DIN ISO 16016
Schutzvermerk beachten
Allgemeintoleranzen
1:1
Maßstab
DIN ISO 2768-mK
Fernbedienung PMS/LMS Bedienschema
Benennung
Materialnummer
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
4
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
right plate
/
Mode
left plate
linke Platte / rechte Platte
2 3
radio hand lamp
Funkhandlampe
Mode
LED off
/
LED off
/
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
3
Blatt
F
A3
B
C
A2
B2
C2
D
D0
E0
E
300
Büro
87
D0
/
D1
light on/off
Licht an/aus
I 0 II
A1
I 0 II
B1
I 0 II
C1
- 0
D1
- 0
E1
[1] LMS 20.0 NZ
Werkstoff
Werkstoffnummer
Mindeststreckgrenze Re in N/mm²
Oberfläche
100075
Änderungsnr.
Fluid-Plan
Dokumenttyp
right plate
/
0.000
--
Version
Dokumentnummer
10001022
00
Revision
87
alte Materialnummer
MOBERMAY
Datum, Freigabe
02.09.2019
6
Nettogewicht in kg
MOBERMAY
left plate
linke Platte / rechte Platte
cable hand lamp
A2
Kabelhandlampe
A1 -
5 6
4
B2
B1
LED off
/
E
Size ISO 14405
LED off
/
nach DIN ISO 16016
Schutzvermerk beachten
Allgemeintoleranzen
1:1
Maßstab
DIN ISO 2768-mK
Fernbedienung PMS/LMS Bedienschema
Benennung
Materialnummer
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
4
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
right plate
/
Mode
left plate
linke Platte / rechte Platte
2 3
radio hand lamp
Funkhandlampe
Mode
LED off
/
LED off
/
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
4
Blatt
F
A3
B
C
A2
B2
C2
D
D0
E0
E
300
Büro
87
D0
/
I 0 II
I 0 II
I 0 II
- 0
- 0
[1] PMS 3/D PIT
Werkstoff
Werkstoffnummer
100075
Änderungsnr.
--
Version
87
D1
light on/off
Licht an/aus
Fluid-Plan
Dokumenttyp
0.000
alte Materialnummer
Dokumentnummer
MOBERMAY
10001022
00
Revision
Datum, Freigabe
02.09.2019
6
right plate
/
A1
B1
C1
D1
E1
Mindeststreckgrenze Re in N/mm²
Oberfläche
Nettogewicht in kg
MOBERMAY
left plate
linke Platte / rechte Platte
cable hand lamp
Kabelhandlampe
A2
A1 -
5 6
4
B2
B1
LED off
/
LED off
/
E
nach DIN ISO 16016
Schutzvermerk beachten
Size ISO 14405
Allgemeintoleranzen
1:1
Maßstab
DIN ISO 2768-mK
Fernbedienung PMS/LMS Bedienschema
Benennung
Materialnummer
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
4
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
right plate
/
Mode
left plate
linke Platte / rechte Platte
2 3
radio hand lamp
Funkhandlampe
Mode
LED off
/
LED off
/
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
5
Blatt
F
A3
B
C
D
E
300
Büro
87
100075
--
Version
87
right plate
/
Werkstoff
Werkstoffnummer
Änderungsnr.
[2] PMS 3.5 Double (Funk)
left plate
Fluid-Plan
linke Platte / rechte Platte
alte Materialnummer
MOBERMAY
10001022
00
Datum, Freigabe
02.09.2019
6
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
0.000
Dokumentnummer
Revision
radio hand lamp
Funkhandlampe
E
nach DIN ISO 16016
Schutzvermerk beachten
right plate
/
5 6
Size ISO 14405
Nettogewicht in kg
1:1
Benennung
Maßstab
DIN ISO 2768-mK
Allgemeintoleranzen
Fernbedienung PMS/LMS Bedienschema
Materialnummer
MOBERMAY
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
left plate
linke Platte / rechte Platte
LED off
/
4
LED off
/
4
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
Mode
2 3
LED off
Mode
LED off
/
/
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
6
Blatt
F
A3
B
C
D
E
300
Büro
87
right plate
/
Werkstoff
Werkstoffnummer
100075
Änderungsnr.
--
Version
87
[2] PMS 3.5 Double (Kabel)
left plate
Fluid-Plan
linke Platte / rechte Platte
A2
A1 -
C2
B2
B1
C2
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
0.000
alte Materialnummer
Dokumentnummer
MOBERMAY
10001022
00
Revision
Datum, Freigabe
02.09.2019
6
Vorwahl
preselection
5 6
cable hand lamp
Vorwahl
preselection
E
nach DIN ISO 16016
Schutzvermerk beachten
Size ISO 14405
Nettogewicht in kg
1:1
Benennung
Maßstab
DIN ISO 2768-mK
Allgemeintoleranzen
Fernbedienung PMS/LMS Bedienschema
Materialnummer
MOBERMAY
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
Kabelhandlampe
right plate
/
left plate
linke Platte / rechte Platte
4
A2
B2
-
4
A1 -
C1
Vorwahl
preselection
2 3
B1
C1
Vorwahl
preselection
A2
B2
C2
D0
32
E0
D0
/
I 0 II
I 0 II
I 0 II
- 0
- 0
D1
light on/off
Licht an/aus
A1
1
B1
C1
D1
E1
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
7
Blatt
F
A3
B
C
A2
B2
C2
D0
D
E0
E
300
Büro
87
100075
D0
/
D1
light on/off
Licht an/aus
I 0 II
I 0 II
I 0 II
- 0
- 0
Werkstoff
Werkstoffnummer
Änderungsnr.
--
Version
87
[6] PMS/LMS + VZ 985021
Fluid-Plan
Dokumenttyp
0.000
alte Materialnummer
Dokumentnummer
MOBERMAY
10001022
00
Revision
Datum, Freigabe
02.09.2019
6
right plate
/
A1
B1
C1
D1
E1
right plate
/
Mindeststreckgrenze Re in N/mm²
Oberfläche
cable hand lamp
Kabelhandlampe
5 6
4
Vorwahl
preselection
left plate
linke Platte / rechte Platte
A2
C1
A1 -
B2
B1
Vorwahl
preselection
left plate
linke Platte / rechte Platte
A2
B2
-
C2
A1 -
LED off
/
B1
E
nach DIN ISO 16016
Schutzvermerk beachten
Size ISO 14405
LED off
/
Allgemeintoleranzen
Nettogewicht in kg
1:1
Maßstab
DIN ISO 2768-mK
Fernbedienung PMS/LMS Bedienschema
Benennung
Materialnummer
MOBERMAY
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
4
right plate
/
LED flashing
/
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
Mode
LED flashing
/
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
left plate
linke Platte / rechte Platte
2 3
LED off
/
radio hand lamp
Mode
LED off
/
Funkhandlampe
1
A
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
Softwareversion: 0.41.001
B
C
D
E
F
A
10
von
8
Blatt
F
A3
B
C
D
E
300
Büro
87
right plate
/
100075
--
Version
87
Werkstoff
Werkstoffnummer
Änderungsnr.
left plate
linke Platte / rechte Platte
Fluid-Plan
[7] PMS/LMS + VZ 985023 (Funk)
alte Materialnummer
MOBERMAY
10001022
00
Datum, Freigabe
02.09.2019
6
MOBERMAY
right plate
/
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
0.000
Nettogewicht in kg
Dokumentnummer
Revision
1:1
Maßstab
left plate
linke Platte / rechte Platte
5 6
radio hand lamp
4
Funkhandlampe
right plate
/
LED off
/
LED flashing
/
E
Schutzvermerk beachten
Size ISO 14405
LED off
/
LED flashing
/
DIN ISO 2768-mK
nach DIN ISO 16016
Allgemeintoleranzen
Fernbedienung PMS/LMS Bedienschema
Benennung
3000007
Materialnummer
Datum, Prüfer
02.09.2019
MOBERMAY
Datum, Ersteller
3.6.2019
5
4
left plate
linke Platte / rechte Platte
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
Mode
2 3
right plate
/
Mode
LED off
/
LED off
/
Shift
LED flashing
left plate
linke Platte / rechte Platte
LED leuchtend / LED aus
LED illuminated
/
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
A
10
von
9
Blatt
F
A3
B
C
D
E
300
Büro
87
Werkstoff
Werkstoffnummer
C2
Vorwahl
preselection
A2
B2
100075
Änderungsnr.
--
Version
87
-
Fluid-Plan
Dokumenttyp
0.000
alte Materialnummer
Dokumentnummer
MOBERMAY
10001022
00
Revision
Datum, Freigabe
02.09.2019
E0
switch position
Schalterstellung
Vorwahl
preselection
C1
A1 -
A2
B1
B2
B2
und
A1
[7] PMS/LMS + VZ 985023 (Kabel)
Mindeststreckgrenze Re in N/mm²
Oberfläche
-
A1 -
B1
simultaneously
B2
Nettogewicht in kg
6
MOBERMAY
and
manual mode
Manueller Modus
Vorwahl
preselection
5 6
C2
A2
A1 -
B2
B1
Umschalten zwischen Automatik- und manuellem Modus
durch gleichzeitiges Drücken von
A1
E
nach DIN ISO 16016
Schutzvermerk beachten
Size ISO 14405
by pressing
Toggle between automatic and manual mode
Allgemeintoleranzen
1:1
Maßstab
DIN ISO 2768-mK
Fernbedienung PMS/LMS Bedienschema
Benennung
Materialnummer
3000007
Datum, Prüfer
02.09.2019
MOBERMAY
5
Datum, Ersteller
3.6.2019
E1
switch position
Schalterstellung
D0
D1
- 0
E0
4
- 0
E1
C2
B2
A2
4
Vorwahl
preselection
C1
A2
A1 -
B2
B1
D0
/
D1
light on/off
Licht an/aus
I 0 II
A1
I 0 II
B1
I 0 II
C1
32
cable hand lamp
Kabelhandlampe
C2
Vorwahl
preselection
2 3
travel duration 2
//
E0
switch position
0.5 sec // 0.75 sec
A2
0.5 sec // 0.75 sec
B2
E1
switch position
0.5 sec // 0.75 sec
A2
C1
automatic mode
Vorwahl
preselection
travel duration 1
Schalterstellung
1 sec // 1.5 sec
1 sec // 1.5 sec
Schalterstellung
0.5 sec // 0.75 sec
0.5 sec // 0.75 sec
B2
0.5 sec // 0.75 sec
Automatikmodus
Verfahrdauer 1 // Verfahrdauer 2
A1
1
B1
A1
B1
1
A
Softwareversion: 0.41.001
B
C
D
E
F
A
B
C
A2
B2
C2
D0
D
E0
E
300
Büro
F
1010
von
A3
Blatt
87
D0
/
I 0 II
I 0 II
I 0 II
- 0
- 0
[A] PMS 3/P PIT
Werkstoff
Werkstoffnummer
100075
Änderungsnr.
--
Version
87
D1
light on/off
Licht an/aus
Fluid-Plan
D1
E1
Mindeststreckgrenze Re in N/mm²
Oberfläche
Dokumenttyp
0.000
Nettogewicht in kg
alte Materialnummer
Dokumentnummer
MOBERMAY
10001022
00
Revision
Datum, Freigabe
02.09.2019
MOBERMAY
6
A2
A1
B1
C1
cable hand lamp
A1 -
Kabelhandlampe
1:1
Maßstab
Fernbedienung PMS/LMS Bedienschema
Benennung
3000007
Materialnummer
Datum, Prüfer
02.09.2019
E
Schutzvermerk beachten
5 6
LED off
/
Size ISO 14405
LED off
/
4
LED flashing
/
LED flashing
/
DIN ISO 2768-mK
nach DIN ISO 16016
Allgemeintoleranzen
MOBERMAY
5
Datum, Ersteller
3.6.2019
4
Licht an/aus
light on/off
LED leuchtend / LED blinkend / LED aus
LED illuminated
LED leuchtend / LED blinkend / LED aus
LED illuminated
activation
Betätigung
32
Mode
2 3
LED off
radio hand lamp
Mode
LED off
/
/
Funkhandlampe
Shift
LED flashing
/
LED leuchtend / LED aus
LED illuminated
1
LED leuchtend / LED blinkend / LED aus
LED illuminated
1
Softwareversion: 0.41.001
A
B
C
D
E
F
Loading...