43-MILLIMETER COMPATIBLE
SWIPE READER
TECHNICAL REFERENCE MANUAL
Part Number 99875146-4
JULY 2008
REGISTERED TO ISO 9001:2000
1710 Apollo Court
Seal Beach, CA 90740
Phone: (562) 546-6400
FAX: (562) 546-6301
Technical Support: (651) 415-6800
www.magtek.com
Cop 08
yright© 1999-20
MagTek®, Inc.
Printed in the United States of America
Information in this document is subject to change without notice. No part of this document may be
reproduced or transmitted in any form or by any means, e
lectronic or mechanical, for any purpose,
without the express written permission of MagTek, Inc.
MagTek is a registered trademark of MagTek, Inc.
REVISIONS
Rev Number
1 22 Oct 99 Initial Release
2
3 13 May 08 Updated dimensions drawing
4 07 July 08 Added Appen dix A
Date Notes
16 May 03 Tech
Front Matter: added ISO line to logo, changed
Support phone number, added new warranty
statement, changed warranty from 90 days to 1
year; Sec 1, Specifications, power requirements:
Changed single and dual track
s from 2.4 V to 2.7 V.
ii
LIMITED WARRANTY
MagTek warrants that the products sold to Reseller pursuant to this Agreement will perform in accordance with
MagTek’s published specifications. This warranty shall be provided only for a period of one year from the da
of the shipment of the product from MagTek (the “Warranty Period”). This warranty shall apply only to the
original purchaser unless the buyer is aut
shall apply only to the first repurchase.
horized by MagTek to resell the products, in which event, this warranty
te
During the Warranty Period, should this product fail to conform to MagTek’s specifications, MagTek wi
option, repair or replace this product at no additional charge except as set forth below. Repair parts and
replacement products will be furnished on an exchange basis and will be either reconditioned or new. All rep
parts and products become the property of MagTek. This limited warranty does not include service to repair
damage to the product resulting from accident, disaster, unreasonable use, misuse, abuse, customer’s negligenc
Reseller’s negligence, or non-MagTek modification of the product. MagT
alleged defective goods to determine whether the warranty is applicable.
Without limiting the generality of the foregoing, MagTek specifically disclaims any liability or warranty for
goods resold in other than MagTek’s original packages, and for goods modified, altered, or treated by customers
Service may be obtained by delivering the product during the warranty period to MagTek (1710 Apollo Court,
Seal Beach, CA 90740). If this product is delivered by mail or by an equivalent shipping carrier, the customer
agrees to insure the product or assume the risk of loss or damage in transit, to prepay shipping charges to the
warranty service location and to use the original shipping container or equivalent. MagTek will return the produc
prepaid, via
all returns.
MAGTEK MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND MAGTEK DISCLAIMS AN
WARRANTY OF ANY OTHER KIND, INCLU
FITNESS FOR A PARTICULAR PURPOSE.
EACH PURCHASER UNDERSTANDS THAT THE MAGTEK PRODUCT IS OFFERED AS IS. IF THIS
PRODUCT DOES NOT CONFORM TO MAGTEK’S SPECIFICATIONS, THE SOLE REMEDY SHALL BE
REPAIR OR REPLACEMENT AS PROVIDED ABOVE. MAGTEK’S LIABILITY, IF ANY, TO RESELLER
OR TO RESELLER’S CUSTOMERS, SHALL IN NO EVENT EXCEED THE TOTAL AMOUNT PAID TO
MAGTEK BY RESELLER UNDER THIS AGREEMENT. IN NO EVENT WILL MAGTEK BE LIABLE T
THE RESELLER OR THE RESELLER’S CUSTOMER FOR ANY DAMAGES, INCLUDING ANY LOST
PROFITS, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF MAGTEK HAS BEEN A
T
HE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.
LIMITATION ON LIABILITY
a three (3) day shipping service. A Return Material Authorization (RMA) number must accompany
DING ANY WARRANTY OF MERCHANTABILITY OR
ek reserves the right to examine the
ll, at its
laced
e,
Y
O
DVISED OF
.
t,
EXCEPT AS PROVIDED IN THE SECTIONS RELATING TO MAGTEK’S LIMITED WARRANTY,
MAGTEK’S LIA
PRODUCTS.
MAGTEK MAKES NO OTHER WARRANTIES WITH RESPECT TO THE PRODUCTS, EXPRESSED OR
IMPLIED, EXCEPT AS MAY BE STATED IN THIS AGREEMENT, AND MAGTEK DISCLAIMS A
IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION ANY IM
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
MAGTEK SHALL NOT BE LIABLE FOR CONTINGENT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES TO PERSONS OR PROPERTY. MAGTEK FURTHER LIMITS ITS LIABILITY OF ANY
WITH RESPECT TO THE PRODUCTS, IN
CONTRACT PRICE FOR THE GOODS.
MAGTEK’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDIES ARE
AND IN THE SECTION RELATING TO MAGTEK’S LIMITED WARRANTY.
BILITY UNDER THIS AGREEMENT IS LIMITED TO THE CONTRACT PRICE OF THE
NY
PLIED WARRANTY OF
KIND
CLUDING ANY NEGLIGENCE ON ITS PART, TO THE
STATED IN THIS SECTION
iii
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance w
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful inte
quired to correct the interference at his own expense.
re
rference in which case the user will be
Canadian DOC Statement
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set o
e Radio Interference Regulations of the Canadian Department of Communications.
th
ut in
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de las classe A prescrites dans l
e Réglement sur le brouillage radioélectrique
édicté par les ministère des Communications du Canada.
CE STA DARDS
Testing for compliance to CE
und compliant to Class A.
fo
This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
requirements was performed by an independent laboratory. The unit under test was
N
UL/CSA
ith
RoHS STATEMENT
When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction
of Hazardous Substances (RoHS) European Directive 2002/95/EC. The mark
written words like “Pb-free” or “lead-free”, or as another clear symbol ( ).
ing is clearly recognizable, either as
iv
TABLE OF CONTENTS
CTION 1. FEATURES AND SPECIFICATIONS.....................................................................................
SE 1
CONFIGURATIONS .................................................................................................................................
SPECIFICATIONS....................................................................................................................................
REFERENCE DOCUMENT......................................................................................................................1
CTION 2. INSTALLATION......................................................................................................................3
SE
MOUNTING...............................................................................................................................................
CONNECTORS.........................................................................................................................................
TIMING......................................................................................................................................................
DATA.........................................................................................................................................................
STROBE ...................................................................................................................................................
CARD PRESENT......................................................................................................................................
APPENDIX A. DRAWINGS .........................................................................................................................7
FIGURES
1
1
3
4
5
5
5
5
Figure 1-1. 43-millimeter Compatible Swipe Reader--------------------------------------------------------------------vi
Figure 2-1. Reader Mounting Dimensions (Typical)---------------------------------------------------------------------
Figure 2-2. Timing ---------------------------------------------------------------------------------------------------------------
F
igure A-1. 43mm Dimensions ----------------------------------------------------------------------------------------------- 8
TABLES
Table 2-1. I/O Connector for Single Track, 8 Pin-------------------------------------------------------------------------
able 2-2. I/O Connector for Dual Track, 8 Pin--------------------------------------------------------------------------- 4
T
3
5
4
v
Figure 1-1. 43-millimeter Compatible Swipe Reader
vi
SECTION 1. FEATURES AND SPECIFICATIONS
The 43-millimeter OEM Swipe Reader has a TTL level interface and is designed for use in retail,
access control, and time and attendance environments. This Reader is in compliance with
industry specifications, including ANSI/ISO Standards 7810, 7811-1 through -6, 7812, and 7813
The Reader can be customized. Bidirectional read capability is available.
CONFIGURATIONS
Configurations and part numbers are as follows:
Part Number Read Cable Length
21044001 Track 1 & 2 3.386" (86mm)
21044002 Track 2 & 3 3.386" (86mm)
21044003 Track 2 3.386" (86mm)
21044004 Track 1 & 2 8.661” (220mm)
SPECIFICATIONS
IEC:
Meets or Exceeds
Requirements for:
Flammability Meets UL94V-0
Recording Method Two-Frequency Coherent Phase (F2F)
Speed Card speed through the unit may vary from:
Power Requirements Single Track: 2.7 to 5.5VDC at 1mA, typical
Output Signal Levels Vol = 0.4V at 2mA
Operating Temperature -30oC to 70o C
Operating Humidity 10% to 90% relative humidity
Life 300,000 passes Single Track
Dimensions Length: 1.693" (43mm)
Cable Length: See configuration table above
Connector See Section 2, Connectors
REFERENCE DOCUMENT
I/O Interface for TTL Swipe Readers, Technical Reference Manual, P/N 99875148
IEC 1000-4-2 ESD (Electro Static Discharge)
IEC 1000-4-3 Radiated EMC Field (2X requirement)
IEC 1000-4-4 Electrical Fast Transient Burst requirement
(transmission on I/O cable)
2-125 ips at 75 bpi
2-60 ips at 210 bpi
Dual Track: 2.7 to 5.5VDC at 2mA, typical
V
= Vcc -0.5V at -2mA
oh
1,000,000 passes Dual Track
Height: 0.902" (22.9mm)
Width: 0.866" (22.0mm)
1
43-Millimeter Compatible Swipe Reader
2
SECTION 2. INSTALLATION
This section consists of installation and checkout of the Reader.
MOUNTING
The dimensions for mounting are shown in Figure 2-1.
Figure 2-1. Reader Mounting Dimensions (Typical)
3
43-Millimeter Compatible Swipe Reader
CONNECTORS
Single Track I/O Connector is shown in Table 2-1, and the Dual Track I/O Connector is shown
in Table 2-2.
Table 2-1. I/O Connector for Single Track, 8 Pin
Pin Number Color Signal
Connector for Single Track, 8 Pin 1 Brown GND
JAE IL-Y-8S-S15C3 2 Gray STROBE
1.5mm Contact Spacing 3 White DATA
4 Blue CARD PRESENT
5 NC
6 NC
7 NC
8 Red VCC
V
Note:
= 2.4 to 5.5 VDC
CC
Table 2-2. I/O Connector for Dual Track, 8 Pin
Connector for Dual Track, 8 Pin 1 Brown GND
JAE IL-Y-8S-S15C3 2 Gray STROBE (Tk 2)
Pin Number Color Signal
4
1.5mm Contact Spacing 3 White DATA (TK 2)
Mates to JAE Headers: 4 Blue CARD PRESENT (Tk2)
Straight Pin Header: 5 Yellow *STROBE (TK 1)
IL-Y-8P-S15T2-EF 6 Orange *DATA (TK 1)
Right Angle Pin Header: 7 Green *CARD PRESENT (TK 1)
IL-Y- 8P-S15L2-EF 8 Red VCC
* Track 1 will be designated Track 3 in P/N 21044002.
V
Note:
= 2.4 to 5.5 VDC
CC
Section 2. Installation
TIMING
CARD PRESENT
DATA
0 0 0 0
1 1 1 0 0 0 0 0 1 1 0
STROBE
Notes:
1. Time out of the CARD PRESENT signal occurs approximately 150 ms after the last strobe transition.
Bit
Time
STROBE WIDTH APPROXIMATELY
25-50% OF BIT TIME
2. DATA is valid 1.0μ sec before the negative edge of STROBE.
Figure 2-2. Timing
DATA
The Data signal is valid while the strobe is low. If the Data signal is high, the bit is a zero. If the
Data signal is low, the bit is a one.
STROBE
The Strobe signal indicates when Data is valid. It is recommended that Data be loaded by the
user with the leading edge (negative) of the Strobe.
CARD PRESENT
Card Present will go low after 14/15 flux reversals from the head. Card Present will return high
150 milliseconds after the last flux reversal.
When no card is being moved through the unit, the Data, Strobe, and Card Present signals are
high. The signal timing diagram shown above represents the data along with other signals that
are generated during the reading process.
5
43-Millimeter Compatible Swipe Reader
6
APPENDIX A. DRAWINGS
The drawing shown in this section show the mounting dimensions of the 43mm Reader.
21044001- Dimensions drawing for 43mm reader
7
43-Millimeter Compatible Swipe Reader
8
Figure A-1. 43mm Dimensions
Loading...