MagTek 100-MILLIMETER SWIPE READER WITH SHIFT-OUT ASIC User Manual

100-MILLIMETER SWIPE READER

WITH SHIFT-OUT ASIC

TECHNICAL REFERENCE MANUAL

Part Number 99875287-3

MAY 2004

REGISTERED TO ISO 9001:2000

1710 Apollo Court

Seal Beach, CA 90740

Phone: [phone]

FAX: [phone]

Technical Support: [phone]

www.magtek.com

Copyright© 2003-2005

MagTek®, Inc.

Printed in the United States of America

Information in this document is subject to change without notice. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose,
without the express written permission of MagTek, Inc.

MagTek is a registered trademark of MagTek, Inc.

REVISIONS

Rev Number Date Notes

1 20 Nov 03 Initial Release
2 9 Mar 04 Sec 1: Added more description in first four

paragraphs; Specifications, Power Requirements:
added idle and sleep modes; Sec 2: Added
connector IO pinouts and -2 and -3 Trk Head
pinouts. Appendix A, updated drawings 21040229
and 21040230.

3 11 May 04 Section 1, Configurations: Editorial corrections;

Section 2: Updated Specs; Appendix A: Added
drawings 21040230 and 21040229.

ii

LIMITED WARRANTY

MagTek warrants that the products sold to Reseller pursuant to this Agreement will perform in accordance with
MagTek’s published specifications. This warranty shall be provided only for a period of one year from the date
of the shipment of the product from MagTek (the “Warranty Period”). This warranty shall apply only to the
original purchaser unless the buyer is authorized by MagTek to resell the products, in which event, this warranty
shall apply only to the first repurchase.

During the Warranty Period, should this product fail to conform to MagTek’s specifications, MagTek will, at its
option, repair or replace this product at no additional charge except as set forth below. Repair parts and
replacement products will be furnished on an exchange basis and will be either reconditioned or new. All replaced
parts and products become the property of MagTek. This limited warranty does not include service to repair
damage to the product resulting from accident, disaster, unreasonable use, misuse, abuse, customer’s negligence,
Reseller’s negligence, or non-MagTek modification of the product. MagTek reserves the right to examine the
alleged defective goods to determine whether the warranty is applicable.

Without limiting the generality of the foregoing, MagTek specifically disclaims any liability or warranty for
goods resold in other than MagTek’s original packages, and for goods modified, altered, or treated by customers.

Service may be obtained by delivering the product during the warranty period to MagTek (1710 Apollo Court,
Seal Beach, CA 90740). If this product is delivered by mail or by an equivalent shipping carrier, the customer
agrees to insure the product or assume the risk of loss or damage in transit, to prepay shipping charges to the
warranty service location and to use the original shipping container or equivalent. MagTek will return the product,
prepaid, via a three (3) day shipping service. A Return Material Authorization (RMA) number must accompany
all returns.

MAGTEK MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND MAGTEK DISCLAIMS ANY
WARRANTY OF ANY OTHER KIND, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.

EACH PURCHASER UNDERSTANDS THAT THE MAGTEK PRODUCT IS OFFERED AS IS. IF THIS
PRODUCT DOES NOT CONFORM TO MAGTEK’S SPECIFICATIONS, THE SOLE REMEDY SHALL BE
REPAIR OR REPLACEMENT AS PROVIDED ABOVE. MAGTEK’S LIABILITY, IF ANY, TO RESELLER
OR TO RESELLER’S CUSTOMERS, SHALL IN NO EVENT EXCEED THE TOTAL AMOUNT PAID TO
MAGTEK BY RESELLER UNDER THIS AGREEMENT. IN NO EVENT WILL MAGTEK BE LIABLE TO
THE RESELLER OR THE RESELLER’S CUSTOMER FOR ANY DAMAGES, INCLUDING ANY LOST
PROFITS, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF MAGTEK HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.

LIMITATION ON LIABILITY

EXCEPT AS PROVIDED IN THE SECTIONS RELATING TO MAGTEK’S LIMITED WARRANTY,
MAGTEK’S LIABILITY UNDER THIS AGREEMENT IS LIMITED TO THE CONTRACT PRICE OF THE
PRODUCTS.

MAGTEK MAKES NO OTHER WARRANTIES WITH RESPECT TO THE PRODUCTS, EXPRESSED OR
IMPLIED, EXCEPT AS MAY BE STATED IN THIS AGREEMENT, AND MAGTEK DISCLAIMS ANY
IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

MAGTEK SHALL NOT BE LIABLE FOR CONTINGENT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES TO PERSONS OR PROPERTY. MAGTEK FURTHER LIMITS ITS LIABILITY OF ANY KIND
WITH RESPECT TO THE PRODUCTS, INCLUDING ANY NEGLIGENCE ON ITS PART, TO THE
CONTRACT PRICE FOR THE GOODS.

MAGTEK’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDIES ARE STATED IN THIS SECTION
AND IN THE SECTION RELATING TO MAGTEK’S LIMITED WARRANTY.

iii

FCC WARNING STATEMENT

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.

FCC COMPLIANCE STATEMENT

This device complies with Part 15 Of The FCC Rules. Operation of this device is subject to the following two
conditions: (1) This device may not cause harmful interference. And (2) This device must accept any interference
received, including interference that may cause undesired operation.

CANADIAN DOC STATEMENT

This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de las classe B prescrites dans le Réglement sur le brouillage radioélectrique édicté par les
ministère des Communications du Canada.

CE STANDARDS

Testing for compliance to CE requirements was performed by an independent laboratory. The unit under test was
found compliant to Class B.

UL/CSA

This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.

iv

TABLE OF CONTENTS

SECTION 1. FEATURES AND SPECIFICATIONS.....................................................................................1

CONFIGURATIONS .................................................................................................................................1

SPECIFICATIONS....................................................................................................................................2

REFERENCE DOCUMENT......................................................................................................................2

SECTION 2. INSTALLATION......................................................................................................................3

MOUNTING...............................................................................................................................................3

CONNECTORS.........................................................................................................................................3

INTERFACE..............................................................................................................................................3

APPENDIX A. ENGINEERING DRAWINGS................................................................................................5

FIGURES

Figure 1-1. 100-millimeter Compatible Swipe Reader ------------------------------------------------------------------vi
Figure A-1. 100-mm Swipe Reader, Tk 1, 2 w/3Tk ASIC -------------------------------------------------------------- 6
Figure A-2. 100-mm Swipe Reader, 3-Tk w/3Tk ASIC ----------------------------------------------------------------- 7

TABLES

Table 2-1. 2-Track and 3-Track I/O Signals------------------------------------------------------------------------------- 3

v

Figure 1-1. 100-millimeter Compatible Swipe Reader

vi

SECTION 1. FEATURES AND SPECIFICATIONS

The 100-millimeter Magstripe Swipe Reader with Shift-Out ASIC is designed for providing
magstripe read capabilities for use in the retail, access control, and time and attendance
environments.

The reader chassis provides an industry standard mechanical footprint, along with magstripe read
capabilities, which comply with the ISO 7810/7811 and AAMVA standards.

The Shift-Out interface provides a "next generation" electronics interface, which simplifies the
process of collecting data bits as the card is swiped.

With Shift-Out technology, the reader's electronics take complete responsibility for recognizing
when a card is being swiped, and for collecting all data bits during the card swipe process.
Subsequently, the reader's electronics then send a "data ready" signal to the host interface, and
allows the host to shift-out the data bits as required.

Key advantages of this product are as follows:

• Low power and "sleep mode" capabilities, which make this product ideal for use in hand-

held battery powered devices. (75uA maximum current draw during sleep mode)

• Low voltage operation. (2.8VDC - 5.5VDC)

• Automatic detection of card swipe and real-time data collection.

• Shift Out data interface. (See Triple Track ASIC with Shift-Out, Specification, P/N

99875259 for details.)

CONFIGURATIONS

Part Number Read Color
MT-211 100 mm Swipe Reader with
3-Track, Shift-Out ASIC
MT-211 100 mm Swipe Reader with
3-Track, Shift-Out ASIC

21040230 Tracks 1 & 2 Black
21040229 Tracks 1,2, & 3 Black

1

100mm Swipe Reader With Shift-Out ASIC

SPECIFICATIONS

STANDARDS

Flammability Meets UL94V-0
Speed Card speed through the unit may vary from:

3 to 60 in/s (7.6 to 152.4 cm/s)

ELECTRICAL

For electrical specifications, see reference document 99875259

MECHANICAL
Dimensions See Appendix A
Connectors See Appendix A
Life 1,000,000 passes

ENVIRONMENTAL
Temperature
Operating:
Storage:
Humidity**
Operating:
Storage:
Altitude
Operating:
Storage:

o

-30

C to +70 oC (-22 oF to +158 oF)

o

-30

C to +70 oC (-22 oF to +158 oF)

10% to 90%
100% noncondensing

0-10,000 ft. (0-3048m)
0-50,000 ft. (0-15,240m)

REFERENCE DOCUMENT

Triple Track ASIC With Shift-Out, Specifications, P/N 99875259

2

SECTION 2. INSTALLATION

This section consists of installation and connection of the Reader.

MOUNTING

The dimensions for mounting are shown below.

CONNECTORS

The connector pin lists are shown below. Connector J2 is provided for easy access without
removing the PC board. If additional strain relief is required, J3 may be used, and a tie wrap can
be routed through the holes adjacent to J3 to secure the cable.

The mating connector is

Housing Molex PN# 51021-0400
Terminal Molex PN# 50058-8000, 4 required.

I/O signal pin list is shown in Table 2-1.

Table 2-1. 2-Track and 3-Track I/O Signals

PCB J2 and J3 Signal

1 VDD
2 GND
3 SO Data
4 SO Strobe

INTERFACE

For interface requirements refer to Triple Track ASIC with Shift-Out, Specifications, P/N

99875259.

3

100mm Swipe Reader With Shift-Out ASIC

4

APPENDIX A. ENGINEERING DRAWINGS

The following Drawings are provided in this section:

Part Number Title

21040230 MT-211 100mm Tk 1, 2 w/3Tk ASIC

21040229 MT-211 100mm 3Tk w/3Tk ASIC

5

100mm Swipe Reader With Shift-Out ASIC

6

Figure A-1. 100-mm Swipe Reader, Tk 1, 2 w/3Tk ASIC

Appendix A. Engineering Drawings

Figure A-2. 100-mm Swipe Reader, 3-Tk w/3Tk ASIC

7

100mm Swipe Reader With Shift-Out ASIC

8