How it Works
Magnum Dynalab
Loading...
MD-309
User Manual
17 pgs180.19 Kb0

Magnum Dynalab MD-309 User Manual

- 1 -
Magnum Dynalab MD 309
HYBRID INTEGRATED AMPLIFIER
INSTRUCTION MANUAL
- 2 -
TABLE OF CONTENTS
SET UP THE MD 309 HYRBID INTEGRATED AMPLIFIER WITH AN EXTERNAL HOME THEATER
PROCESSOR .................................................................................................................................................................... 7
- 3 -
Dear Valued Customer
Thank you for choosing the Magnum Dynalab Great care has been given to the design, manufacturing and selection of components for the insures optimum listening enjoyment for many years.
When using these high grade components, a considerable length of time is required for the high quality break-in disc or white noise from a FM tuner will help ensure optimum performance as quickly as possible.
Once again, thank you for including a MAGNUM DYNALAB product in your entertainment system. We are sure that you will have years of listening pleasure from your product at www.magnumdynalab.com, and if there is anything else we can do, please call us on our toll free number, 1-800-551-4130, or contact us via email:
info@magnumdynalab.com.
Respectfully yours, Larry Zurowski
President
MD 309 Hybrid Integrated Amplifier
MD 309 Hybrid Integrated Amplifier
MD 309 Hybrid Integrated Amplifier
MD 309 Hybrid Integrated Amplifier
. This complete process
to reach its full potential. Using either a
. Please be sure to register your
.
- 4 -
UNPACKING YOUR MD 309 HYBRID INTEGRATED AMPLIFIER
Carefully inspect all sides of the shipping carton for damage. If there are marks or holes in the carton make note of the location in relation to the unit inside. Any obvious dents or scuff marks should alert you to the possibility of damage. Carefully remove the MD 309 Hybrid Integrated Amplifier from the end caps and wrapping, inspect all sides. Pay special attention to the corresponding areas on the unit where damage was found to the shipping carton. If damage is evident, document the type and extent of the damage, then repack the unit and call the dealer.
KINDLY DO NOT SEND THE UNIT BACK TO THE SHIPPER UNTIL YOU HAVE BEEN ASKED TO DO SO.
DO NOT DISCARD THE PACKING MATERIALS AND CARTONS. Should there be a necessity to return the unit for any reason, it must arrive safely and suitably packaged in order for our receiver to accept it from the carrier. If the unit has incurred damage as a result of improper packaging, it is not likely that a claim for the damage against the carrier will be successful.
Likewise, we will ship your unit back to you only in factory-approved packaging, however, if the unit were to arrive at the factory on anything other than factory approved packaging, we reserve the right to return the unit in factory-approved packaging and charge the cost of the packaging to the shipper. This is the only way we can assure you of a safe return (damage by carrier excepted).
- 5 -
SETTING UP THE MD 309 HYBRID INTEGRATED AMPLIFIER
1. Position the unit away from any spot which may have extremes in temperatures.
2. Place the unit on a very rigid surface capable of holding 50 pounds (22 KG).
3. The heat sinks located inside the unit are used to keep the unit at a safe
operating temperature. It is important that they are not covered and that the unit is not installed in a closed area where there is little air circulation. Ensure at least 2” of clearance on the left and right of the device, and 5” of clearance above the unit to allow for proper ventilation.
4. Unwrap the EIA AC cord and plug the EIA end into the rear socket marked
Input
. Plug the other end of the AC cord into a 120/220/230/240 volt continuous AC power supply. Be sure that the voltage marked on the rear of the unit is the same as the AC source that you are using.
5. Hook up your speakers to the back of the unit insuring that the positive (+)
terminal on the speaker is hooked up to the positive (+) output terminal on the 309, likewise that the negative (-) is correctly hooked up. Be sure that all the connections are tightly affixed.
6. Turn the power switch on the front panel touchscreen to the ON position. The
screen will turn on displaying the Magnum Dynalab Logo as the 309 is warming up. The 309 will then display the current input setting and volume level.
Power
INPUT PRESET VOLUME PROCEDURE
Use this feature to preset the volume levels of all your audio inputs. The idea is you can match the levels of all your inputs so that when you are changing inputs during play, they will all be at the same level.
1. Use the input selector knob on the left of the 309 or the direct access from the
remote to select the input you want to adjust.
2. Once you are on the input you want to adjust hit the “set-up” button on the touch-
screen. Use the “up” or “down” arrow button to change the default volume level on the input. Once you have the desired level hit the “save” button to preset your level.
3. Repeat this procedure for each input you have until your inputs are all level with
each other or as you desire them.
- 6 -
Loading...
+ 11 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use