25.March.2016
Ebike kit installation manual
Manual 1.0
Ebike kit installation manual
1
2
4
3
5
Motor
Display
PAS Senor
7
9
8
Battery 36V
Light 36V
6
10
11
12
Part Name:
1.Brake lever set 2.Display 3.Wheel set 4.Pas disc 5.PAS sensor 6.Controller 7.R2 battery 8. Rear carrier
9. Rear carrier band 10.Thumb shift throttle 11.Charger 12.Display extension cable
Some of the above parts are different in different countries, only for reference. Please in kind prevail.
1
1. PAS sensor&PAS disc installing manual
PD-DH2
PS-DH-SSP
PAS sensor&PAS disc should be assembled
on left side of the 2 kinds of bottom bracket.
For 2 kinds of bottom bracket above, need to match special PAS sensor&PAS disc which should be
assembled on the right side. For more details, please contact customer service.
2
1.2.1. Assemble PAS disc,fasten metal ring to fix it.
Fine tune the distance between
PAS sensor and PAS disc.
The head of PAS sensor should aim at
the round hole around the PAS disc.
or
down tube
seat tube
fix ribbon
( SIDE VIEW )
connect with the
connector on controller
fix ribbon
1.2.2. Assemble PAS sensor and fix with ribbon.
( FRONT VIEW )
3
2. Motor wheel installation
Inner tube , Tire
2.1. Assemble inner tube & tire on motor wheel and pump up
4
If there is disc brake on the rear wheel of your bike, please follow below installation. If not, please jump
page 2.2&2.3.
2.2. Remove screws and shim from motor.
2.3. Fix disc brake first, then twist screw. (pay attention to disc brake pad direction)
5
If there is cassette freewheel on the rear wheel of your bike, please follow installation 2.4 below. If not,
please follow 2.5.
Cassette Freewheel
2.4. Please assemble cassette freewheel according to the sequence in the picture above.
Rotating Freewheel
2.5. Please assemble fix rotating freewheel according to the sequence in the picture above.
6
2.6. Please pay attention to wheel installing direction after assembling rear wheel
according to the sequence in the picture above.
connect with controller
2.7. Fix motor wheel, fasten the nut, cover with axle cap and make the motor cable
connect with controller.
7
3. Installation manual for controller
Display
Motor
Pas Sensor
3.1 Connect controller with motor, display, PAS Sensor, battery. Put controller into the
controller case.
3.2 Put the battery case into the rear carrier.
8
4. Installation manual for E-brake lever, Throttle and Display
6
4.1 Take off the original grip and brake lever, assemble the display, brake lever set,
thumb shift throttle in turn from kits, and then instal grip.
The side of kit assembling on handlebar are different in different countries, only for
reference. Please in kind prevail.
6
4.2 Instal brake cable and throttle cable, connect E-brake lever and throttle with
display, connectdisplay cable with display extension cable, and then connect with
controller.
9
5. Display instruction
5.1. Switch on&switch off
when power off, press" " display can switch on.
when power on, press" " display can switch off.
when power on, press" " for 3s, display will switch off.
5.2. Full Screen
5.3. Icon indication in comprehensive display
area
Wheel diameter
Cycle
Time
Max speed
Error code
Total Distance
Trip distance
5.8. 6KM
Press "UP" for 2s, bike will run under
conditionof electrical power-assisted.
5.9. Electric current
5.10. Button instruction
When power on, click " ",turn on backlight.
Click " SET ",switch comprehensive display area.
Press " SET " 3s,switch to enter into SET interface.
SET" 0 " setting riding model-POWER.
NORMAL. ECO.
SET" 1 " click DOWN, trip 1 distance.
trip 1 time, re-set max speed.
SET" 2 " setting speed limiting.
SET" 3 " setting wheel diameter.
SET" 4 " setting KM/H or MPH
SET" 5 " setting qty of speed magnetic
steel ( 6pieces defult / 1 piece)
Press " SET "1s, save settings and exit.
5.4. Power
5.5. Speed
5.6. Gear
Press ”UP” or “DOWN“ to adjust gear
5.7. Error Code
There will be error code when system
brake down.
5.11. Power off automatically after 5 minutes
When speed keeps ZERO for 5 minutes, display will
switch off automatically.
5.12. Error code indication
[ 0 ] No error
[ 1 ] Electric current error
[ 2 ] Throttle error
[ 3 ] Motor stop phase
[ 4 ] Hall error
[ 5 ] Brake error
[ 6 ] Under voltage
[ 7 ] Motor stalling
[ 8 ] Communication controller receiving error
[ 9 ] Communication display receiving error
10
Loading...