Magnum MI-16150 Operating Manual

MODEL NO.:

MI-16150

OPERATING MANUAL

S

TOP

STAR

T

TABLE OF CONTNETS

Table of contents ________________________________________________

Safety rules ____________________________________________________

Specications __________________________________________________

Instructions for operations _________________________________________

Tilting the table _________________________________________________

Mounting spindle drum ___________________________________________

Selection guide for drum to table insert _______________________________

Maintenance of spindle sander _____________________________________

Troubleshooting _________________________________________________

Assembly diagram _______________________________________________

1

2

3

4

5

6

7

8

9

10-14

01

SAFETY RULES

Read carefully before operating the machine

1. Learn the machine’s applications and limitations, as well as the specic potential hazards

particular
to this machine. Follow available safety instructions and safety rules carefully.

2. Keep working area clean and be sure adequate lighting is available.

3. Do not wear loose clothing, gloves, bracelets, necklaces, or ornament. Wear face, eye, ear,
respiratory and body protection devices, as indicated for the operation or environment.

4. Keep hands well away from cutter head and all moving parts. Do not clear chips and
sawdust away with hands. Use a brush.

5. Make sure the spindles are moving at operation speed before sanding.

6. Do not push the sanding spindles to hard. The spindles will perform better and be safer
working at the rate for which it was designed.

7. Whenever possible use a dust collector with shaving hood to minimize health hazards.

8. Never leave the machine with the power on.

9. Keep children away. Make sure that visitors are kept at a safe distance from the work area.

10. Use recommended speed sanding accessory, and workpiece material.

11. Never stand on tool. Serious injury could occur if the tool is tipped or if the sanding tool is
unintentionally contacted.

12. Be sure sanding spindles are securely locked in the machine.

13. Use suitable support if stock does not have a at surface.

14. Keep guards in place and in working order. If a guard must be removed for maintenance or
cleaning make sure it is properly attached before using the tool again.

15. Be sure that key and adjusting wrenches have been removed before turning power on.

16. Only use accessories designed for the machine. Use of accessories not recommended by
may result in a risk of injury.

17. Make sure tool is properly grounded. If tool is equipped with three-prong plug, it should be
plugged into a three-pole electrical receptacle. Never remove the third prong.

18. Always disconnect tool before servicing and when changing accessories such as spindle

sizes.

19. To make sure the cover of the magnetic switch has covered up before the machine

electried.

20. Hold material rmly against the table.

21. Do not use this spindle sander for other than it’s intended use. If used for other purposes,
disclaims any real or implied warranty and holds itself harmless for any injury, which may
result from that use.

02

SPECIFICATIONS

MODEL MI-16150

Table size (L x W) 616 x 616 mm

Table tilt 0 ~ 45°

Spindle speed 1725rpm

Oscillations 59/min

Oscillation stroke 39 mm
Sanding sleeve length 150 ~ 230 mm
Max. workpiece height 55 ~ 160 mm

Dust port diameter 100 mm

Motor 1HP

Table height 990 mm

Overall (L x W x H ) 616 x 616 x 990 mm

Weight 145 kg

03

# The above specications are not binding. supplier reserves the right to amend any specications or

design characteristics without prior notice.

INSTRUCTIONS FOR OPERATIONS

1. Select spindle that is smaller than the curve to be sanded.

2. Use an insert plate that comes closest to the spindle without touching it.

3. Make sure that spindle is properly positioned in taper sleeve socket. With the wrench provided

, tighten the nut. NOTE: Never over tighten; it may be difcult to remove the spindle later.

4. When table is set at a 90° angle, sanding may be done from any corner, or location on table
around spindle.

5. When table is positioned at any angle other than 90°, it is necessary to position the work piece
over the centerline, as shown on table surface.

6. Always lock the table with the hand nut when setting at any angle, also to prevent movement
lock the tilting gear shaft.

7. Always loosen both table lock and tilting gear lock before changing the angle position of the
table. Never force the table if it does not tilt easily, reason may be that the locks are still
engaged. Never attempt to over ride the stop locks, this will cause damage to the tilting
performance.

8. A backing board is recommended when sanding thin pieces of metal or any other material. A
backing board can be easily constructed by using a piece of wood the length of the table,
pushing it into the spindle until a half circle is formed. Clamp each end of the board to the table
and proceed to sand the thin material.

9. Before leaving the machine remove any particles or pieces left over, make sure the table in
90°.

04