Magnum Ruutu L 6.0kW, Ruutu C 6.0kW, Ruutu L 6.6kW, Ruutu L 9.0kW, Rutuu C 9.0kW Operating Instructions Manual

Operating instructions

Magnum Ruutu L 6.0kW - 6.6kW - 9.0kW - 10.5kW

Magnum Ruutu C 6.0kW - 9.0kW

Magnum Klubi 6.0kW - 9.0kW

2

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

These instructions are intended for the owner of the sauna or the person
responsible for its maintenance, as well as for the electrician who installs the
sauna stove. The electrician will give these instructions to the owner of the

sauna or the person responsible for its maintenance after the stove has been
installed successfully. The owner of the sauna stove or the person responsible for
its maintenance must store these instructions for the entire lifespan of the sauna
stove, because changes may be made to the components. Keeping the original
instructions ensures that the circuit diagrams and the connection methods used
during maintenance works are intended for this particular sauna stove.

The owner of the sauna must read these instructions carefully before first
using the sauna stove. The instructions contain full operating and maintenance

instructions, installation instructions, a troubleshooting guide and the warranty
terms for the sauna stove and its parts.

The electrician must ensure that the device has been disconnected from the
power supply before performing any installation or maintenance work. The

fitter should avoid touching the internal components and integrated circuits of the
device unnecessarily. Touching can result in a discharge of static electricity,
which may damage the device or one of its electrical components. The electrician
must ensure that the device is grounded correctly and that all connections have
been completed according to the instructions.

The only purpose of this sauna stove is to heat the sauna to a suitable sauna
temperature. The sauna stove must not be used for any other purpose. The

sauna stove must never be covered, and the person using the sauna should always
check the sauna stove before heating it, to ensure that there is nothing flammable
or anything that does not belong to a sauna either on top or beside the sauna
stove.

3

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

TABLE OF CONTENTS

1. Using the device – Finlandia Control Centre ............................................................................................................ 4

1.1 – Control Functions – Finlandia Control Centre ..................................................................................................... 4

1.2 – Menu structure – Finlandia Control Center ......................................................................................................... 5

2. Using the sauna stove ................................................................................................................................................ 5

2.1 – Adjustable settings ............................................................................................................................................... 5

...................................................................................................................................................................................... 5

2.2 – target temperature ................................................................................................................................................ 5

2.3 – Heating time ......................................................................................................................................................... 6

2.4 - Timer .................................................................................................................................................................... 6

2.5 – Turning the sauna off ........................................................................................................................................... 6

2.6 – Directions for using the sauna .............................................................................................................................. 7

3. Installation of the sauna stove ................................................................................................................................... 8

3.1 – Installation stages ................................................................................................................................................. 9

3.2 – Thermostat sensor .............................................................................................................................................. 13

3.3 - Finlandia control panel ................................................................................................................................. 14

Surface Installation: .................................................................................................................................................... 14

Recessed mount: ......................................................................................................................................................... 15

4. Installation illustrations and renderings .................................................................................................................. 16

4.1- Thermostat and controller – Installation in the sauna .......................................................................................... 16

4.2- Mechanical ventilation......................................................................................................................................... 17

4.3 - Natural gravitational ventilation ................................................................................................................... 18

4.4 - Piling stones in the sauna stove .................................................................................................................... 19

4.4.1 Stone piling stages Ruutu L: ....................................................................................................................... 19

4.4.2 - Stone piling stages Klubi and Ruutu C: ................................................................................................... 20

4.5 -Sauna stove wall bracket ............................................................................................................................... 21

5. Technical information and safety distances of the sauna stoves ............................................................................. 22

5.1 – Illustration of safety distances ............................................................................................................................ 22

5.2 -Physical measurements and technical specifications of the sauna stoves ...................................................... 23

6. Warranty ................................................................................................................................................................. 25

7. Connection diagram ................................................................................................................................................ 26

8. Sauna stove care and maintenance .......................................................................................................................... 27

9. Problems/troubleshooting guide ............................................................................................................................. 28

4

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

1. USING THE DEVICE – FINLANDIA CONTROL CENTRE

1.1 – CONTROL FUNCTIONS – FINLANDIA CONTROL CENTRE

Sauna stove On/Off
Menu/Selection button
Decrease
Increase
Light control
The heating/timing indicator light

Sauna stove light’s indicator light
Menu settings indicator light
Number display

Legend for the parts of the control panel:

1.

On/Off button. Pressing this button turns the sauna stove on and off. If the timer has been set,
pressing this button starts the timer for heating the sauna.

Tip: Pressing this button for a longer duration overrides the timer and starts the heating
of the sauna stove immediately.

2.

Menu button: by pressing this, you can move through the menus of the device as follows:
(Default mode –> Target temperature –> Heating time –> Timer –> Default mode)

3.

(˅) button. This button is used to decrease the default values.

4.

(˄) button. This button is used to increase the default values.

5.

Lights button: by pressing this, you can turn on the sauna stove’s light. Pressing it again turns

the light off. (Only used in models with lights or a separate fibre kit)

6.

“Device on” indicator light. This light is constantly on while the sauna stove is on. The light
”glows” when the timer is in use. The light is turned off when the sauna stove is not on.

7.

Sauna stove light’s indicator light. This light is on as an indicator of the fibre light kit of the
sauna stove / sauna being on.

8.

Menu settings indicator light. This light comes on when a menu setting is adjusted. (timer,
the time the device is on, the target temperature of the sauna stove)

9.

Three-digit display

5

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

1.2 – MENU STRUCTURE – FINLANDIA CONTROL CENTER

Default status (temperature display) Target temperature Heating time Timer

The adjustment menus of the device are shown in the image above. The user can move from one menu to
another using the Menu button. When the sauna stove is on, the (˄) and (˅) buttons can be used to adjust the
settings, as shown in the image above. The dot in the lower right corner will be on when the resistors warm
up (indicated with an arrow).

2. USING THE SAUNA STOVE

2.1 – ADJUSTABLE SETTINGS

Parameter

Adjustment

range

Adjustment

increment

Default value

Please note!

Target temperature

adjustment

40-110°C

1°C

60°C

Heating time

1 h - 6 h

0.5 h

1 h

See Section 2.3

Timer

0.5 – 24 h

0.5 h

0 h

Not in use

2.2 – TARGET TEMPERATURE

The sauna’s target temperature may be adjusted in increments of one Celsius. The minimum temperature is 40 degrees

and the maximum temperature is 110 degrees. This setting is saved.

The target temperature can be adjusted in two different ways.

1. Pressing the Menu button shows the target temperature on the screen.

You can use the +/˄ and –/˅ buttons to change the value. If you do not press any buttons, the

controller will stop displaying the target temperature menu automatically in approx. 10 seconds. You
can also exit the menu by pressing the Menu button repeatedly.

2. When the sauna temperature is on the display, pressing the (+/˄) or (–/˅) button causes the controller

to move directly to the target temperature settings. Exiting the menu happens as described in section 1.

6

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

2.3 – HEATING TIME

You can set the sauna stove’s heating time to be between 1 h and 6 h. The adjustment takes place in increments of 0.5

h. The time value has to be set when the device is turned off. You can move to this setting from the default move by
pressing the Menu button twice.

It is possible to reduce the time the stove is on when the sauna is heating. You can increase or decrease the time of the
sauna session by pressing the (+/˄) or (–/˅) button when the remaining time is on the display. In this case, the
adjustment increment is 15 min. This setting is not saved to the memory. This setting can also be changed by pressing
the Menu button twice in default mode.

2.4 - TIMER

You can move from the default mode to the timer by pressing the Menu button three times in a row. The (+/˄) and (–
/˅) buttons are used to change the timer’s setting. The adjustment range is 0.5 h – 24 h, and the adjustment increment
is 0.5 h. If this value is zero, the timer is not in use.

This setting can only be changed when the device is off.

2.5 – TURNING THE SAUNA OFF

Turn the sauna stove’s power on using the control switch at the lower part of the sauna

stove. Make sure that the sauna stove is not covered, and that there is nothing in the sauna
that does not belong there. Pressing the Controller’s On/Off button makes the sauna stove
start heating until the target temperature has been reached. The stove heating indicator
light in the controller will switch on. The decimal mark lights up on the lower right side
of the screen to indicate that the resistors are on. (If the timer has been set, the On/Off
button turns the timer on and the sauna stove begins heating only after the timer has run
out). The On/Off button turns the sauna stove off.

Tip: If the timer has been set but the sauna stove is not on, you can override the timer by pressing

the On/Off button and keeping it pressed for a few seconds. This causes the stove to
start heating up immediately. The timer’s setting nevertheless remains in the device
memory.

When the device is on, the default mode (temperature) and the remaining time
alternate on the display. The alternation interval is approx. 10 seconds.

1- CONTROL SWITCH

7

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

2.6 – DIRECTIONS FOR USING THE SAUNA

• Heat the sauna stove once before first use, as the protective substances in the new stones may give off odours while

the sauna stove is heating. Ensure there is sufficient ventilation After the heating is completed, open the sauna
window (if applicable).

• Make sure that the sauna stove has not been covered, and that there is nothing in the sauna that does not belong

there (laundry, children’s toys, etc.)

• The recommended temperature if 55 – 70 degrees.

• The sauna stove heats to a suitable sauna temperature in approx. 25 – 80 minutes, depending on the size of the sauna

stove, the size of the sauna, and the ventilation.

• User water that is suitable for domestic use when throwing water on the sauna stove. The use of seawater is

forbidden.

• Do not throw water on the sauna stove if there are people next to it, as the water splashing from the sauna stove and

the steam it creates are scalding hot.

• Move carefully in the sauna, as the floors may be slippery.

• The manufacturer recommends heating the sauna stove until hot, and turning it off at the beginning of the sauna

session. It will spare the resistors considerably if cold water is not thrown on a resistor glowing red-hot. The mass
of stones will keep the sauna hot for a long time, and “once-off heating” enables to have a sauna session of about
20 – 30 min before the sauna stove has to be switched on again.

Quality requirements for the heating water

Water condition:

Effect:

Recommendation:

Water containing humus

Colour, taste, deposits

<12 mg/l

Water containing iron

Colour, odour, taste, deposits

<0.2 mg/l

Hardness: the most important
substances are manganese
(Mn) and chalk or calcium
(Ca)

Deposits

Mn: <0.05 mg/l
Ca: <100 mg/l

Water containing chloride

Health risk

Use is banned

Seawater

Fast corrosion

Use is banned

8

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

3. INSTALLATION OF THE SAUNA STOVE

• The electrical installation may only be performed by a qualified electrician

• Instructions for the electrical installation are provided in the circuit

diagram in these installation instructions as well as on the sticker on the
sauna stove.

• The electrical installation work may only be performed by an electrician

qualified for the job, in accordance with applicable regulations.

• The sauna stove is connected to the power grid semi-permanently with H07RN-

F or similar rubber cable.

• Check the required cable dimensions in the table below.

• Please note! The use of a PVC cable as a connection cable is not permitted.

• The power switch in the device is a so-called control switch, and it does not

fully de-energise the sauna stove.

Sauna stove

POWER

FUSE

FEED CABLE

SAUNA SIZE

Magnum 6 – 6.6

6.6 KW

3x10 A

5x1.5 mm2

5-9 m3

Magnum 9

9 KW

3x16 A

5x2.5 mm2

8-15 m3

Magnum 10.5

10.5 KW

3x16 A

5x2.5 mm2

10-20 m3

9

Magnum Kiuas – Operating and installation instructions 03.04.2019

Starsauna Oy Technical Support:
Pistotie 4 [phone] (from 8-16)
15860 Hollola, Finland [e-mail]

3.1 – INSTALLATION STAGES

1. Remove the stainless steel frame from the upper part of the sauna stove.

2. Remove the protective plastics from the metal parts.

3. Fold the sauna stove’s cardboard box up and set the sauna stove on its side on the cardboard. Ensure that the sauna

stove does not become scratched.

4. Open the hatch at the base of the sauna stove.

5. Feed the Finlandia panel wire (8x0.25 mm2 LYII grey cable) through the lowest cable gland and connect the wires

on the circuit board on the terminal block with the numbers 1-8. The terminal block can be detached from the
main board for easier installation. The terminal block is located in the lower left section. Tighten the cable gland

after the installation is complete.

Order of wires on the board

1. Brown

2. Grey

3. Pink

4. White

5. Green

6. Yellow

7. Blue

8. Red

6. Connect the thermostat sensor according to SECTION 3.2. Feed the thermostat sensor wire (4x0.25 mm2 silicone

cable, beige wire) through the second-lowest cable gland and connect the wires on the circuit board, to the 4-slot
terminal block adjacent to the Finlandia panel block. The terminal block can be detached from the main board for
easier installation. Tighten the cable gland after the installation is complete.