Magnepan MG .7 User Manual

Page 1
Magneplanar .7 Instruction Manual
Quick Set-Up Instructions
Remove the steel magnetic strip from the front of the speakers. If the fabric sticks to the diaphragm, use a high tack tape to gently pull the fabric loose from the diaphragm.
e .7 has exceptional phase characteristics that are accomplished without the use of compensation networks. To realize the optimum phasing, the .7 should be angled inward as shown in the diagrams below. (Do not place parallel to the front wall.) Tweeters on the inside will give a precise image for a single listener. For a large "sweet spot" and multiple listeners, place tweeters on the outside. Especially for tweeters on the inside, the speakers must be angled suciently inward as shown in the diagrams below so that the tweeter is not ahead in time.
Tweeter attenuation may be necessary for rooms with hard, reective walls. See Section 14 below.
1 Introduction 2
2 General Description 2
3 Carton Contents 2
4 Packaging 2
5 Assembly 3
6 Hookup 4
7Caution 4
8 Speaker Placement 4
9 Bass Response 5
10 Left/Right 5
11 Stereo Width and Imaging 6
12 Phasing 7
13 Room Acoustics 7
14 Optional Tweeter Attenuation 7
15 Maintenance 8
16 Specifications 8
Revision—3-19–2015
Page of 1 8
Page 2
1 Introduction
Congratulations on your purchase. e Magneplanar .7 loudspeaker was conceived and designed by perfectionists, for perfectionists. Due to the elegant simplicity and ruggedness of the design, the Magneplanar .7 loudspeaker will give many years of trouble-free service.
2 General Description
e .7 is a 2-way, full-range, quasi-ribbon design with a quasi-ribbon bass/ midrange and tweeter.
3 Carton Contents
• 1 pair .7 loudspeakers
• 4 each feet or 2 each oval bases with!
4 each 3 1/2 inch bolts and 4 each stand-offs
• 8 each foot bolts
• 2 each 1 ohm resistors
• 2 each Magneplanar logos
• 1 each Allen wrench
• 1 instruction manual
4 Packaging
Save all packaging. If you need to transport the speakers, they can be shipped safely only in the original packaging. You may never have to return your loudspeakers, but should the occasion arise, they should not be shipped in any packaging but the original. Should you discard it, packaging is available.
Revision—3-19–2015
Page of 2 8
Page 3
5 Assembly
Fig. 1
Installation of oval base
Revision—3-19–2015
Page of 3 8
Page 4
Remove the set crews from the bottom of the speaker with the 1/8 Allen wrench provided. Install the long bolts as shown in the diagram. Do not use a screwdriver until the bolt has engaged the threads. Care must be taken not to cross-thread the bolts. e bolts on the back of the speaker for the L-feet can be discarded. Tighten the screws as much as is possible by hand. ere will be some play in the panel. It is not perfectly rigid, but this has not detrimental eect on the sound quality. e movement allows the panel to be tilted back slightly for better high frequencies when standing.
Installation of L-feet
Install the L-feet on the back of the speaker and tighten the screws.
6 Hookup
e .7 features unique, high current connectors which provide optimum contact area with the speaker cables up to 10 gauge (or for banana connectors). Simply strip 1/2" of insulation from the end of the cable. Insert the cable into the terminal (observing polarity), and tighten the set screws with the Allen wrench provided. Banana plug connectors can be used and locked in place with the set screws. Spade lug adapters are available from your Magneplanar dealer for spade connectors that are incompatible with the Magneplanar high current connector.
7 Caution
e terminal plate states a maximum fuse value of 4 amps Type 3AG ("normal" or "fast blow"). e bass section does not require fusing protection. is fuse value should never be increased or bypassed. Do not use slow-blow fuses. BURNED OUT TWEETERS ARE NOT COVERED UNDER THE WARRANTY.
8 Speaker Placement
Proper speaker placement and room acoustics can have a greater eect on a music system than upgrading one of the components in the system. Unfortunately, there is no denitive guideline which will cover all possible
Revision—3-19–2015
Page of 4 8
Page 5
listening rooms. Some experimentation is required for locating the optimum position. e following are a few general guidelines:
9 Bass Response
Play music with repetitive bass. Try the speakers in several possible locations in the room. Begin experimenting with the speakers about 3 feet from the front wall. Try moving the speakers forward or backward in increments of 6 to 12 inches. One position in the room should be noticeably better than others. Also experiment with your listening location to avoid standing waves.! Need more bass?! Most of the area of any full-range Maggie is devoted to bass reproduction. (In the case of the 20.7, 76% of the total radiating area is devoted to bass.) e Magneplanar Bass Panel offers you the exibility to add bass diaphragm area to t the needs of your room. From the $600 pair MMG to the 20.7, the Maggie Bass Panel can get the bass/midbass "just right".
10 Left/Right
e .7's are matched pairs and mirror-imaged. e serial number for each speaker in the pair is the same, except for a "1" or "2" following each serial number. As you face the front of the speakers, the speaker with the serial number ending with the "1" aer its serial number has the tweeter near the le edge, and the speaker serial number ending with the "2" has the tweeter near the right edge.
Revision—3-19–2015
Page of 5 8
Page 6
11 Stereo Width and Imaging
Once you have located the best position for the speakers and your chair for bass performance, separate the speakers by 50-60% of the distance from your chair to the speakers. For example, if your chair is 10 feet from the speakers, move the speakers 5-6 feet apart. Now, move the speakers apart in increments of 3 or 4 inches at a time, listening carefully at each position. At some point you will start to hear two separate speakers instead of a stage eect or continuous image. When this occurs, your speakers are too far apart. Begin moving the speakers back in small increments until you notice a point at which you achieve one cohesive sound stage.
Fig. 1
Fig. 2
Revision—3-19–2015
Page of 6 8
Page 7
12 Phasing
To realize the optimum phasing, the .7 should be angled inward as shown in the diagrams above. (Do not place parallel to the front wall.) For a larger "sweet spot" and multiple listeners, place tweeters on the outside. Single listeners may choose to place the tweeters on the inside. If you do, cant the speakers inward suciently so that the tweeter is not ahead of the bass/ midrange in time as shown in the diagrams above.
13 Room Acoustics
e judicious use of damping material can improve the sound. Acoustical damping can be achieved with household items or wall hangings. A word of caution--when audiophiles discover the eectiveness of damping material, they sometimes overdo it (on the premise that if a little is good, more is better). Before making a permanent change to your room, experiment with the positioning of the damping material. Usually a portion of one or two parallel walls should have some damping. However, it is a trial-and-error process.! An over-damped room will provide very precise imaging, but the sound will seem "dead." An under-damped room may heighten the illusion of being in a concert hall, but the imaging will seem imprecise with all the instruments mixed together. "Hardness" or over-bright sound is usually the result of a room with hard surfaces (glass, hard paneling,etc.). Moderation is the key.! Diusers are also helpful to improve the acoustics of a room. Contact your Magnepan dealer for more information on the proper use of diusers.
14 Optional Tweeter Attenuation
ere are two principal reasons for needing to attenuate the Magneplanar Quasi-Ribbon Tweeter and Super Tweeter:
A. Pop or rock recordings oen exhibit a pronounced rise in the treble
region.
B. e Magneplanar Quasi Ribbon Tweeter is very ecient in its total energy
dispersion. If the surrounding walls are exceptionally reective, the overall perceived acoustical balance will be tipped towards a "hot" high end.
Revision—3-19–2015
Page of 7 8
Page 8
Attenuation is performed through insertion of a resistor in place of the jumper. e pair of 1.2 ohm resistors will attenuate the tweeter 1-2 dB. Other values are available from your Magneplanar dealer.
15 Maintenance
Light vacuuming of the grille cloth is possible.
16 Specications
System Description: 2-way, quasi-ribbon speaker.
Frequency Response: 45Hz--22kHz" +/- 3dB
Sensitivity: 86 dB, 500Hz, 1 meter, 2.83V
Impedance: Nominal 4 Ohms
Dimensions: 15 1/4 W" X 54 1/4 H" X 1 1/4 D" inches
Warranty: LIMITED. 3 Years to Original Owner
Shipping Weight: 76 lbs.
* Because there are no universally accepted methods for loudspeaker measurements, frequency response specications may be stated by most manufacturers without reference to measurement techniques and/or specic locations in rooms. Magneplanar loudspeaker frequency response specications are average performance levels that may reasonably be expected in normal installations.
Revision—3-19–2015
Page of 8 8
Loading...