Philips/Magnavox REM250, 4 FUNCTION UNIVERSAL REMOTE - WITH BACK LIGHTED KEYPAD User Manual
Thank you for purchasing a Philips Magnavox 4 device universal
remote control. This universal remote control will operate
your Television,Video Cassette Recorder,DVD, Cable Converter
Box or Audio Receiver/Amplifier. Before you can use your new
remote control,you will need to program it to operate the specific components you wish to control. This remote features:
• Channel Scan,a convenient way to "channel surf"
by scanning channels.
• Auto Scan code search to help program remote
control for a variety of components, including
older/discontinued models.
• Built-in Sleep Timer.
• Controls for basic functions, including Power,
Channel Selection,Volume,Play and Record.
KEYS AND FUNCTIONS
2
1
2
3
5
4
7
10
11
13
14
15
13
12
10
3
8
5
9
6
16
4 Function
with Back Lighted Keypad
Universal Remote
Instructions . . . . . . . . . . . . . 2
Instrucciones . . . . . . . . . . 10
Instructions . . . . . . . . . . . . 19
Replacement and Code Saver
When the batteries need replacing the remote control will stop working and will require two (2) new "AA" alkaline batteries for continued
operation. Once you remove the old batteries,program settings and
codes will be saved for 10 minutes,allowing adequate time to insert
new ones.
However,if you do not replace the batteries within the allotted time
(e.g., 10 minutes), you will have to reprogram the remote control.
USING THE LIGHTED KEYPAD
When activated,the remote control features a lighted keypad that illuminates all of the remote control keys whenever you press any key.
1. To turn on the keypad back light, press LIGHT once.
The keypad will remain lit for 5 seconds after you r elease
any key.
2. To turn off the keypad back light, press LIGHT once
again. (The keypad will not light whenever you press any
key.)
PROGRAMMING YOUR REMOTE CONTROL
Philips/Magnavox Components
The remote control can control up to three different components and
is already pre-programmed for use with newer Philips/Magnavox
audio/video equipment.Unless you want to change a factory setting,
skip the programming instructions and simply start using your new
remote control.
Programming Other Components
To control component brands other than Philips/Magnavox,you’ll need
to perform the following steps to manually program the remote with
codes listed under Manufacturer’s Codes on pages 28 through 37. Or
as an alternative,you can use the Auto Scan feature,on page 5, to program your component codes.
The following chart lists the remote component keys and what type of
device each key will control:
Key Programmed to Control
TV TV
VCR VCR or DVD
CBL Cable Box
AUD Amplifier/Receiver
NOTE: If you want the component keys to control other types of
devices,you’ll need to reassign the component keys.See page 5.
IMPORTANT: Please completely read and review the following
steps before proceeding. We recommend highlighting the codes (starting on page 28),for the brands you wish to program or writing them
down in the supplied chart.
Setup Codes for My components
TV ___ ___ ___ ___
VCR ___ ___ ___ ___
CBL ___ ___ ___ ___
AUD ___ ___ ___ ___
To Manually Program the Remote Control:
1. Manually turn on a component (e.g.,TV,VCR,etc.) and, if
applicable, inser t media (e . g., cassette).
2. On the remote control,press a component key
once (e.g., TV,VCR,CBL, orAUD).
3. Press and hold SET (approximately 5 seconds) until the
red light blinks twice,then release SET.
4. Enter the first four-digit code for your brand of component. If performed correctly, the red light will blink
twice.
4
SETTING UP YOUR REMOTE CONTROL
Before using your new remote control,you will need to obtain and
install new batteries,as described below. Then you’ll also need to program the remote control with the correct code numbers for your specific components. See instructions starting on page 4.
ABOUT BATTERIES
Note: The remote requires two (2) new "AA" alkaline batteries (not
supplied). Do not mix old and new batteries or mix alkaline with manganese-type batteries.
Installing Batteries
1. On the back of the remote control, push the tab and lift the battery compartment cover off.
2. Match the + and – marks on the
batteries to the + and – marks in
the battery case and insert two (2)
"AA" alkaline batteries.
3.Press the battery cover back into
place. The tab should click when
the cover is locked.
4. Test the unit by pressing
POWER and any Component key
(e.g., TV, VCR, CBL, etc.). If the
batteries are inserted correctly the
red indicator light will blink once.
Battery Saver
The remote has a Time Out feature that will automatically deactivate the
remote control if a key is depressed for more than 30 seconds. This feature will help conserve the battery life should your remote control get
stuck in a place where keys remain depressed (e.g., between the sofa
cushions).
3
1 Red Indicator Light
The Red Indicator Light blinks
to show that the remote control is working and also provides feed back during programming sequences.
2 Component Keys
Press TV, VCR, CBL or
AUD once to select a home
entertainment component to
control.
3 CH Keys
Use CH+ (or CH-) to select
the next higher (or lower)
channel for the selected home
entertainment component.
4 SLEEP Key
Press SLEEP to activate your
TV’s internal sleep timer (not
available for all TVs) or to program timer.
5 VOL Keys
Use VOL+ (or VOL-) to
raise (or lower) the sound
volume.
6 POWER Key
Press POWER once to turn
on or off the selected home
entertainment component.
7 MUTE Key
Press MUTE once to turn
sound off or on.
8 LAST Key
Press LAST once to recall
the last channel.
9 SET Key
Use SET for all programming
sequences.
10 Keypad
Use the keypad (0-9) to
directly enter in channels (for
example, 09 or 31). The keypad is also used for all programming sequences, such as
entering in your programming
codes.
11 SCAN Key
Press SCAN once to change
channels every 3 seconds.
Press it again to stop the scan.
12 ENTER
Use ENTER once after
entering channel numbers on
some TV models.
13 VCR T ransport Keys
Use the VCR Transport Keys
to control your VCR. Press
REC twice to record a tape.
14 TV/VCR
Press TV/VCR once to view
VCR playback or TV through
the VCR.
15 FAV CH Key
Use to pre-program up to 10
favorite channels.
16 LIGHT Key
Press LIGHTonce to turn on
or off the keypad backlight.
1
2
3
1. Press and hold SET until the red light blinks twice, then
release SET.
2. Enter 9-9-2. The red light will blink twice.
3. Press the Component key (e.g., TV,VCR, etc.) to be
moved once, then press the Component key (e.g.,
AUD, etc.) to be re-assigned once. When reassignment is done,the red light will blink twice to
confirm your choice.
4. The re-assigned key is now ready to be programmed for
the component. See Programming Your Remote Control on
page 4.
Example – Re-assigning The AUD key to be a DVD (Or VCR) key:
For example,to have the remote control a TV,a Cable Converter,and
two VCRs, you will need to re-assign the unused AUD key to operate
the second VCR as follows:
1. Press and hold SET until the red light blinks twice, then
release SET.
2. Enter 9-9-2. The red light will blink twice.
3. Press VCR once.
4. Then press AUD once. When re-assignment is done,
the red light will blink twice to confirm your choice.
5. The AUD key is now ready to be programmed for your
DVD (or VCR) player. See Programming Your Remote
Control on page 4.
ABOUT OTHER FEATURES
Volume Lock
The remote control is set at the factory to control the volume independently while in the TV,VCR,and CBL modes.
To control the volume from one mode (e. g., TV) while in another
mode (e.g., VCR or CBL), perform the instructions below to lock the
volume setting. This procedure will not affect separate control of your
audio component’s volume in the AUD modes.
NOTE: By pressing AUD before entering the sequence below,the
remote control will operate your home theater volume controls in all
modes.This feature does not apply to component keys that have been
re-assigned.
1. On the remote control,press TV once.
2. Press and hold SET until the red light blinks twice, then
release SET.
3. Press VOL+. The red light will blink twice.
Scan Key
The SCAN key allows the remote control to scan the TV,VCR and
CBL channels. When activated, the remote control will change channels every 3 seconds.
1. On the remote control,press TV,VCR or CBL once.
2. Press SCAN once . Scanning will star t with the current
channel, then proceed to the next channel up,and continue until all channels of your TV,VCR or CBL component are scanned.
3. To stop scanning channels, press SCAN.
Favorite Channel Scan
The FAV CH Key can be pre-programmed with up to 10 of your
favorite channels and scans these only.
1 On the remote control,press a component key once
(e.g., TV,VCR, CBL) .
6
5. Aim the remote control at the component and press
POWER ONCE. It should turn off. If it does not
respond,repeat steps 2 and 3, trying each code for your
brand until you find one that works. If it still does not
work, try using Auto Scan (see below) on how to program your component.
6. Repeat steps 1 through 5 for each component you want
to program into the remote control.
NOTES: Press each key within 10 seconds of the previous entry.
Otherwise, the remote control will exit the programming mode.
If you press SET at any time (except during step 3), the remote con-
trol will exit the programming mode without saving your entries. You
will have to start with step 1 to begin programming again.
Programming With Auto Scan
If your component does not respond to the remote control after trying all codes listed for your brand,or if your brand is not listed at all,
try searching for your code using Auto Scan. For example,to search
for a code for a TV:
1. On the remote control,press TV once.
2. Press and hold SET until the red light blinks twice,then
release SET.
3. Aim the remote control at the TV and press SCAN. The
red light will blink twice.
4. Continue aiming the remote control at the TV (which
may take up to 5 minutes) until it turns off. Immediately
press any key except VOL-, LAST,SCAN, or SET.
If SCAN is pressed again after any key stops Auto Scan,the remote
will continue Auto Scan of the next ID from where it stopped.
If you have passed by the code that turns off the TV,press VOL- one
or more times until the TV turns on again.
5. To lock in the code and exit Auto Scan,press and release
SET the red light will blink twice.
6. To search for codes of other components,repeat steps 2
through 5,but substitute the appropriate key (e.g.,VCR,
CBL) for the (VCR or Cable) component you are searching for.
NOTES: In the search mode, the remote will send IR (infrared)
codes from its library to the selected device, star ting with the most
popular code first.
Checking the Auto Scan Codes
If you have set up the remote control using Auto Scan,you can now
find out which four-digit code is operating your component:
1. On the remote control,press a component key once
(e.g., TV,VCR, CBL or AUD).
2. Press and hold SET until the red light blinks twice, then
release SET.
3. Enter 9-9-0. The red light will blink twice.
4. To view the code for the first digit, press 1 once. Wait
3 seconds, count the red light blinks (e. g., 3 blinks = 3)
and write down the number.
NOTE: If a code digit is "0" ,the red light will not blink.
5. Repeat step 4 three more times for remaining digits. Use
2 for the second digit, 3 for the third digit and 4 for the
fourth digit.
6. To find codes of other components, repeat steps 1
through 5,but substitute the appropriate key (e.g.,VCR
or CBL) for the component you are checking. As
before,write down each four-digit code.
Re-Assigning Component Keys
The remote can be set up to control any combination of four home
entertainment components. By following these instructions,you can
re-assign or duplicate a component key onto an unused component
key.
5
8
Press component*
key once (e.g., CBL).
Press SET
until Red Light
blinks twice;
release SET.
Press VOL+ once.
Volume now controlled
through component
selected in step 1.
x 2
123
* NOTE: Component must have
volume capabilities.
Volume Lock
QUICK FEATURES SETUP GUIDE
This guide is provided here for your convenience as a quick reference for performing remote control sequences.
Turn on
component
(e.g., TV).
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 4-digit code
for your brand;
Red Light blinks
twice after last #.
Press POWER
once; if no
response,
repeat steps
with next code.
x 2
x 2
#
# # #
12 3 45
Component Setup
Turn on
component
(e.g., TV).
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Aim remote at
component; press
SCAN once. When
off, press any
key* to stop.
x 2
Press SET
until Red Light
blinks twice;
release SET
to lock code.
x 2
12 3 4 5
* NOTE: Not VOL-, LAST, SCAN, or SET.
Auto Scan
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 9-9-0;
the Red Light
will blink twice.
Press 1 once for 1st digit.
Wait 3 sec. and count blinks.
Number of blinks equals
value of code digit.
Repeat with 2, 3, and 4.
x 2
x 2
12 3 4
Code Verification
Press component key
to be moved once
(e.g.,VCR).
Press SET
until Red Light
blinks twice;
release SET.
x 2
3
Press component key
to be reassigned once
(e.g., AUD). Red Light will
blink twice. Reassigned key is
now ready for programming.
41
Enter 9-9-2;
the Red Light
will blink twice.
x 2
2
Device Re-Assignment (e.g., AUD Key Becomes Secondary VCR Key)
Press and release
SET once. Red
Light blinks twice.
Repeat for up to
10 channels.
x 2
5
Enter channel
Note: Some brands
require ENTER
after channel.
4
Programming The FAV CH Key
Press component
key once
(e.g., TV).
Press SET
until Red Light
blinks twice;
release SET.
Enter 9-9-6;
the Red Light
will blink twice.
x 2
x 2
123
2. Press and hold SET until the red light blinks twice, then
release SET.
3. Enter 9-9-6. The red light will blink twice.
4. Enter first channel,e.g.,07. For some component brands
the ENTER key must be pressed after the digits,this will
count as a key press. Skip Step 5 if ENTER is needed as
next channel number will be ready to program without
pressing SET.
5. Press and release SET once (do not hold down). Red
light blinks twice.
6. Enter second channel,third channel etc. until 10th channel is reached. Note: If 3 digits plus an Enter is needed for newer TVs/Cable channels, these will not be programmed. Only 3 entries per channel can be accepted.
7. FAV CH program exits after 10th channel is pro-
grammed or if SET is pressed for 3 seconds.
8. Pressing FAV CH key activates the remote to cycle
through the favorite channels every 3 seconds until
favorite channel is locked in by pressing any key.
Note: Favorite channel scan will only work on the component it is
programmed to.
Punch Through
The VCR T ransport keys (e.g., REW, PLAY, FFWD,REC, STOP,
AND PAUSE) are set at the factory to control the VCR even if TV
or CBL is the selected mode. In other words,VCR control "punches
through" regardless of what mode is on. Moreover,you do not have to
press VCR before pressing the mode key.
However, if AUD is the selected mode, the VCR Transpor t Keys will
not control the VCR unless you press the VCR first.In these two
modes,the VCR Transport Keys will operate the functions for the
selected component.
Sleep Feature
Press SLEEP key to activate your component’s internal sleep timer.
(May not be available for all components.) If the component does not
have a sleep function,the first press of the SLEEP key activates the
remote’s built-in sleep timer. Timer can be set to a maximum of 90
minutes.
To Set the Remote’s Built-in Timer
1. Press SLEEP key once,15 minute timer is set. Red light
blinks once.
2. Additional key presses within 10 seconds will increase
the timer value in 15 minute increments up to a maximum of 90 minutes. For each press of the SLEEP key,
the red light will blink to indicate how many 15 minute
increments have been programmed, e.g., one blink for
first press, two blinks for the second press, etc. Sleep
timer activates 10 seconds after the last press of the
SLEEP key. The red light will blink once every 15 seconds to indicate that the timer is running.
NOTE: Once the sleep timer is running, the sleep timer is automati-
cally canceled if any other key is pressed. The remote IR must be
pointed to the component to turn off component when timer ends.
To Activate Built-in Sleep Timer if component has
Sleep function
1. On the remote control,press a component key once
(e.g., TV, VCR,CBL). Sleep feature does not apply
to AUD mode.
2. Press and hold SET until the red light blinks twice, then
release SET.
3. Enter 9-7-0. The red light will blink twice.
4. Follow instructions above to Set Timer.
To reset to component Sleep function follow steps 1
through 3 above. At the end of step three,the red light
will blink four times to indicate the remote is reset to
component Sleep function.
7
SETUP CODES FOR TELEVISION
CÓDIGOS DE PROGRAMACIÓN PARA TELEVISIÓN
CODES DE PROGRAMMATION DU TÉLÉVISEUR
A-Mark 0032
AOC 0032,0048,0059, 0214
Admiral 0122,0492
Adventura 0075
Aiko 0121
Akai 0059
Alaron 0208
Ambassador 0206
America Action 0209
Ampro 0780
Anam 0209
Anam National 0084
Archer 0032
Audiovox 0032,0121,0209, 0480, 0652
Baysonic 0209
Belcor 0048
Bell & Howell 0045, 0183
Bradford 0209
Brockwood 0048
Broksonic 0032,0265,0492
CXC 0209
Candle 0059, 0075, 0085
Carnivale 0059
Carver 0083
Celebrity 0029
Cineral 0121,0480
Citizen 0059, 0068, 0075, 0085, 0089,
0121,0309
Clairtone 0214
Concerto 0085
Contec 0209, 0214
Craig 0209
Crosley 0083
Crown 0068, 0209
Curtis Mathes 0045,0059,0068, 0076, 0080,
0083,0085,0089, 0122, 0174,
0183,0195,0480, 0495
Daewoo 0048, 0068, 0121, 0480, 0652,
0653
Daytron 0048
Denon 0174
Dumont 0046,0048
Dwin 0749, 0803
Electroband 0029,0214
Emerson 0048,0068, 0183, 0206, 0207,
0208,0209,0214, 0265, 0309,
0311,0492,0652, 0653
Envision 0059
Fisher 0183,0188
Fujitsu 0208, 0712
Funai 0200, 0208,0209
Futuretech 0209
GE 0050,0076,0080, 0084, 0122,
109
TROUBLESHOOTING
Red Indicator Light does not
blink when you press a key.
Replace the batteries with two
(2) "AA" alkaline batteries (see
Page 3).
The VOL+,VOL- and MUTE
keys are not functional.
Make sure that the volume control is locked to a component
that has volume capabilities and is
programmed into the remote
control.
Red Indicator Light blinks when
you press a key, but home entertainment component does not
respond.
Make sure you are aiming the
remote control at your home
entertainment component and
that you are within 15 feet of the
component you are trying to
control.
The remote control does not
control home entertainment
components or commands are
not working properly.
Try all listed codes for the component brand being set up. Make
sure all components can be operated with an infrared remote
control.
CH+, CH- and LAST do not
work for your RCA TV.
Due to an RCA design (1983-
1987),only the original remote
control will operate these functions.
Changing channels does not
work properly.
If original remote control
required pressing ENTER to
change channels,to change channels,press ENTER on the
remote after entering a channel
number.
Tried Auto Scan and still could
not find a working code.
Try Auto Scan again after clearing
out the component key as follows: Press and hold SET until
Red Light blinks twice, then
release. Next enter 9-9-2. Then
press and release the component
key to be cleared twice.
NOTE: To clear all set up codes and restore functions to Default,
press SET until red light blinks twice,release SET and enter 9-8-1.
Caution:When this clear feature is performed, please note that all of
your set up codes will be reset to the default codes and you will need
to reprogram components.
PROBLEM: SOLUTION:
Philips 0083
Pilot 0048,0059, 0068
Pioneer 0195
Portland 0048, 0068, 0121
Prism 0080
Proscan 0076
Proton 0032, 0207, 0495
Pulsar 0046,0048
Quasar 0080,0084, 0194, 0279
RCA 0047,0048, 0076, 0080, 0119,
0122,0164,1476
Radio Shack 0048,0059, 0068, 0076, 0085,
0183,0194,0207, 0209
Realistic 0048, 0059, 0068, 0085,0183,
0194,0207,0209
Rhapsody 0214
Runco 0046, 0059, 0632
SSS 0048,0209
Sampo 0059, 0068
Samsung 0048, 0059, 0085, 0089, 0207
Samsux 0068
Sansei 0480
Sansui 0492
Sanyo 0183,0188
Scimitsu 0048
Scotch 0207
Scott 0048,0207,0208, 0209, 0265
Sears 0076, 0083, 0085, 0183, 0185,
0188,0200,0207, 0208
Semivox 0209
Semp 0185
Sharp 0068,0122, 0194
Shogun 0048
Signature 0045
Simpson 0216
Sony 0029
Soundesign 0207,0208,0209
Spectricon 0032
Squareview 0200
Starlite 0209
Supre-Macy 0075
Supreme 0029
Sylvania 0049, 0059,0083, 0125
Symphonic 0200
TMK 0085, 0206, 0207
Tandy 0122
Tatung 0032, 0084
Technics 0080, 0279
T echnol Ace 0208
Techwood 0032,0080, 0085
Teknika 0045,0048,0068, 0083, 0085,
0089,0121,0179, 0208, 0209
Telefunken 0085
Toshiba 0089,0183,0185
Tosonic 0214
Totevision 0068
12
0164,0207,0311, 0480
Gibralter 0046,0048,0059
GoldStar 0048, 0059, 0085, 0207
Gradiente 0082,0085
Grunpy 0208,0209
Hallmark 0207
Harley Davidson 0208
Harman/Kardon 0083
Harvard 0209
Hitachi 0045, 0085, 0174, 0180
Infinity 0083
Inteq 0046
JBL 0083
JCB 0029
JVC 0082
Janeil 0075
KEC 0209
KTV 0059, 0068, 0209, 0214, 0309
Kenwood 0048,0059
Kloss 0075
LG 0085
LXI 0076, 0083, 0183, 0185,0207
Logik 0045
Luxman 0085
MEI 0214
MGA 0048, 0059, 0179, 0207
MTC 0048, 0059, 0085, 0089, 0214
Magnavox 0049, 0059, 0083*, 0125,
0208,0216
Majestic 0045
Marantz 0059,0083
Matsushita 0279
Megatron 0032, 0174, 0207
Memorex 0045,0085, 0179, 0183, 0207,
0279,0492
Midland 0046, 0068, 0076, 0080, 0164
Minutz 0050
Mitsubishi 0048, 0122, 0179, 0207
Motorola 0084,0122
Multitech 0209
NAD 0185,0195,0207
NEC 0048,0059, 0085
NTC 0121
Nikko 0059, 0121, 0207
Noshi 0047
Onwa 0209
Optimus 0183,0195, 0279
Optonica 0122, 0194
Orion 0208, 0265, 0492
Panasonic 0080,0084, 0279
Penney 0032, 0047, 0048,0050, 0059,
0068,0076,0080, 0085, 0089,
0164,0185,0207
Philco 0048, 0049, 0059, 0083, 0125,
0174,0492
11
* Default code
GoldStar 0066, 0067
Gradiente 0029,0037
HI-Q 0076
Harley Davidson 0029
Harman/Kardon 0067,0110
Harwood 0101
Headquarter 0075
Hitachi 0029, 0070, 0071, 0134
Hughes Network Systems 0071
JVC 0037,0070, 0096
Jensen 0070
KEC 0066, 0307
KLH 0101
Kenwood 0067,0070, 0096
Kodak 0064, 0066
LXI 0066
Lloyd’s 0029, 0237
Logik 0101
MEI 0064
MGA 0072, 0090, 0269
MGN T echnology 0269
MTC 0029, 0269
Magnasonic 0307
Magnavox 0029, 0064, 0068, 0110*,
0178
Magnin 0269
Marantz 0064,0110
Marta 0066
Matsushita 0064,0191
Memorex 0029,0064, 0066, 0068, 0075,
0076,0077,0133, 0238, 0269,
0336,1191
Minolta 0071, 0134
Mitsubishi 0072, 0077, 0090, 0096
Motorola 0064,0077
Multitech 0029, 0101
NEC 0067,0070, 0096, 0133
Nikko 0066
Nikon 0063
Noblex 0269
Olympus 0064
Optimus 0066,0077, 0133,0191, 0461,
1191
Optonica 0091
Orion 0031, 0213, 0238, 0508
Panasonic 0064,0191, 0254, 0645, 1191
Penney 0064, 0066, 0067,0071, 0083,
0269
Pentax 0071, 0134
Philco 0064, 0238, 0508
Philips 0064,0091,0110, 0647
Pilot 0066
Pioneer 0096
Portland 0049
Profitronic 0269
14
* Default code
Vector Research 0059
Victor 0082
Vidikron 0083
Vidtech 0048,0207
Viking 0075
Wards 0045,0048,0049, 0050, 0059,
0083,0085,0125, 0194, 0207,
0208
White W estinghouse 0492,0652,0653
Yamaha 0048, 0059
Zenith 0045,0046, 0121, 0492, 0653
Zonda 0032
SETUP CODES FOR VCR
CÓDIGOS DE PROGRAMACIÓN PARA VIDEOCASETERA.
CODES DE PROGRAMMATION DU MAGNÉTOSCOPE.
Admiral 0077,0238
Adventura 0029
Aiko 0307
Aiwa 0029, 0066,0336
Akai 0070,0090,0135
America Action 0307
American High 0064
Asha 0269
Audiovox 0066
Beaumark 0269
Bell & Howell 0133
Broksonic 0031,0150,0213, 0238, 0508
CCE 0101,0307
Calix 0066
Canon 0064
Capehart 0049
Carver 0110
Cineral 0307
Citizen 0066, 0307
Colt 0101
Craig 0066, 0076, 0101, 0269, 0300
Curtis Mathes 0064,0070,0089, 0191
Cybernex 0269
Daewoo 0049, 0074, 0307, 0590
Daytron 0049
Denon 0071
Dynatech 0029
Electrohome 0066
Electrophonic 0066
Emerex 0061
Emerson 0029,0031, 0066, 0072, 0090,
0150,0213,0237, 0238, 0241,
0307,0508,0590
Fisher 0076, 0083, 0133
Fuji 0062,0064
Funai 0029
GE 0064,0077,0089, 0231, 0269
Garrard 0029
Go Video 0461,0555
13
SETUP CODES FOR CABLE
CÓDIGOS DE PROGRAMACIÓN PARA CABLE
CODES DE PROGRAMMATION DU CÂBLORÉCEPTEUR
ABC 0030,0032, 0036, 0037, 0040,
0042,0043,0046
Allegro 0182, 0344
Americast 0928
Antronix 0051
Archer 0051, 0182, 0826
Belcor 0085
Bell & Howell 0043
Bell South 0928
Cable Star 0085
Cabletenna 0051
Cableview 0051
Century 0182
Citizen 0182, 0344
Colour V oice 0054
Comtronics 0069
Contec 0048
Eastern 0031
Emerson 0826
Everquest 0044, 0069
Focus 0429
GC Electronics 0085
Garrard 0182
Gemini 0044, 0826
General Instrument 0040,0305,0505, 0839
GoldStar 0069, 0173
Goodmind 0826
Hamlin 0038, 0049, 0063, 0288
Hitachi 0040
Hytex 0036
Jasco 0044, 0182, 0344
Jerrold 0032*,0040, 0041, 0043,
0044,0305,0505, 0839
Magnavox 0056
Memorex 0029
Movie Time 0092
NSC 0092
Oak 0036,0048
Optimus 0050
Panasonic 0029,0050, 0136
Paragon 0029
Philips 0054,0056,0182
Pioneer 0173, 0562, 0906
Popular Mechanics 0429
Pulsar 0029
Quasar 0029
RCA 0050
Radio Shack 0044,0344, 0826, 0912
Recoton 0429
Regal 0049, 0288
Regency 0031
16
* Default code
Proscan 0089,0231
Protec 0101
Pulsar 0068
Quarter 0075
Quartz 0075
Quasar 0064, 0191, 1191
RCA 0064,0071, 0077, 0089, 0134,
0135,0178,0231, 0269
Radio Shack 0029
Radix 0066
Randex 0066
Realistic 0029, 0064, 0066, 0075,0076,
0077,0091,0133
ReplayTV 0643, 0645
Ricoh 0063
Runco 0068
STS 0071
Samsung 0074, 0269
Sanky 0068, 0077
Sansui 0029, 0070, 0096, 0238, 0300,
0508
Sanyo 0075,0076, 0133,0269
Scott 0072,0074,0150, 0213, 0241
Sears 0029, 0064, 0066, 0071, 0075,
0076,0083,0133, 0134
Semp 0074
Sharp 0077,0091
Shintom 0101
Shogun 0269
Singer 0101
Sony 0029,0061, 0062, 0063, 0064
Sylvania 0029, 0064,0072, 0110
Symphonic 0029
TMK 0237, 0269
Tatung 0070
Teac 0029, 0070
Technics 0064, 0191
Teknika 0029,0064,0066
Thomas 0029
Tivo 0647
Toshiba 0072,0074,0241
Totevision 0066, 0269
Unitech 0269
Vector 0074
Vector Research 0067
Video Concepts 0074, 0090
Videosonic 0269
Wards 0029,0064,0071, 0076, 0077,
0089,0091,0101, 0110, 0178,
0241,0269
White W estinghouse 0238,0307
XR-1000 0029, 0064, 0101
Yamaha 0067
Zenith 0029,0062, 0063, 0068, 0238,
0508
15
SETUP CODES FOR RECEIVERS
CÓDIGOS DE PROGRAMACIÓN PARA RECEPTOR.
CODES DE PROGRAMMATION DU RÉCEPTEUR.
ADC 0560
Adcom 0645
Aiwa 0150, 0187,0218, 0434, 1118,
1434
Capetronic 0560
Carver 0037, 0071, 0218, 0389, 1118,
1218
Casio 0224
Clarinette 0224
Curtis Mathes 0109
Denon 0033,1133, 1189
Emerson 0453
Fisher 0071, 0248, 0389
Garrard 0453,0492
Harman/Kardon 0139,0218,0920
JBL 0139
JVC 0103
Kenwood 0056,0071, 0106, 0215, 1056,
1342,1598
Koss 0453
LXI 0210
Linn 0218
Lloyd’s 0224
MCS 0068,0375
Magnavox 0218, 0224, 0420, 0560, 1118,
1218
Marantz 0068,0218, 1118, 1218
Modulaire 0224
NAD 0349
Nakamichi 0126,0376
Onkyo 0164
Optimus 0071,0109, 0206,0210, 0215,
0248,0560,0699, 0767, 0830,
1052
Panasonic 0068,0338, 1547
Penney 0224
Philips 0218,0420,1118, 1218, 1298
Pioneer 0043, 0109, 0179, 0560,0659,
1052
Proscan 1283
Quasar 0068
RCA 0083,0375, 0389, 0560, 1283
Realistic 0192, 0210, 0224
Sansui 0218, 0375, 1118
Sanyo 0248,0830
Scott 0192,0351
Sharp 0215
Sherwood 0520,0531
Sony 0187,0503, 1087, 1187, 1287
Soundesign 0699
Sunfire 1342
18
Rembrandt 0040
Runco 0029
SL Marx 0069
Samsung 0069, 0173
Scientific Atlanta 0037,0046,0506, 0906
Signal 0044,0069
Signature 0040
Sprucer 0050
Starcom 0032, 0044
Stargate 0044,0069, 0826
Starquest 0044
Sylvania 0030
TV86 0092
Tandy 0287
Teleview 0069
Texscan 0030
Tocom 0041, 0042
Toshiba 0029
Tusa 0044
Unika 0051, 0182
United Artists 0036
Universal 0051, 0085, 0182, 0220
Viewstar 0056,0092, 0287
Zenith 0029,0554, 0928
Zentek 0429
SETUP CODES FOR AMPLIFIERS
CÓDIGOS DE PROGRAMACIÓN PARA AMPLIFICADOR.
CODES DE PROGRAMMATION DU AMPLIFICATEUR.
Aiwa 0435
Carver 0298
Curtis Mathes 0329
Denon 0189
GE 0107
Harman/Kardon 0921
JVC 0360
Linn 0298
Magnavox 0298
Marantz 0298,0350
Nakamichi 0350
Optimus 0329,0424
Panasonic 0337
Philips 0298,0921
Pioneer 0042, 0329
Realistic 0424
Sansui 0350
Sony 0249,0718
Soundesign 0107
Technics 0337
Victor 0360
Wards 0042,0107
Yamaha 0383
17
Teac 0192, 0492
Technics 0068, 0338, 1337, 1338, 1547
Thorens 1218
Victor 0103
Wards 0043,0083,0109, 0187, 0218
Yamaha 0205, 0215
Yorx 0224
Zenith 0886
SETUP CODES FOR DVD
CÓDIGOS DE PROGRAMACIÓN PARA DVD.
CODES DE PROGRAMMATION DU DVD.
Denon 0519,0663
GE 0551
Harman/Kardon 0611
JVC 0587,0652
Kenwood 0563
Magnavox 0532
Marantz 0568
Mitsubishi 0550
Onkyo 0532,0656
Optimus 0600
Panasonic 0519,0661
Philips 0532,0568
Pioneer 0554, 0600, 0661
Proscan 0551
RCA 0551
Samsung 0602
Sharp 0659
Sherwood 0662
Sony 0562
Technics 0519
Theta Digital 0600
Toshiba 0532
Yamaha 0519, 0574
Zenith 0532,0620
19
Loading...