Magnavox MSD126 User Manual

Owner’s Manual
Owner's Manual
AUDIO
OUT
VIDEO OUT
COAXIAL
R
L
Y
S-VIDEO
OUT
COMPONENT VIDEO OUT
CR/P
R
DIGITAL AUDIO OUT
CB/P
B
STEREO AUDIO / VIDEO RF Modulator
(commercially available)
TO TVCHANNEL VIDEO AUDIO
R L3 4
ANT IN
AC 120V
(Back of TV)
Audio/Video
Cables
(Supplied)
(Back of this unit)
RF Cable (Not supplied)
Antenna
Cable Signal
3
2
1
Antenna in jack
Please read before using this unit.
DVD/CD Player
MSD126
Supplied Accessories
Remote control (NB074UD) with two AA batteries
Connecting to RF Modulator
If your TV has AUDIO/VIDEO input jacks, see the section “Connections” on page 6. If not, it is still possible to connect this unit to your TV by using a STEREO AUDIO/ VIDEO RF modulator (commercially available). In this case, follow the instructions below.
1) Connect the AUDIO/VIDEO output jacks of this unit to the AUDIO/VIDEO input jacks of your RF modulator by Audio / Video cables.
2) The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV, and then connect the RF cable to your RF modulator (usually marked “ANT IN”).
3) Connect your RF modulator to your TV by another RF cable.
4) Set your RF modulator’s channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area. If your RF modulator has a modulator/antenna switch, set it according to your RF modulator’s manual.
5) Turn on your TV and choose the same channel as you set the RF modulator’s channel 3/4 switch to. For more details, follow the instructions supplied with the RF modu­lator.
If your TV does not have AUDIO / VIDEO input jack.
Hint
The quality of picture may become poor if the unit is connected to
an RF modulator.
If you need additional operating assistance
after reading this owner’s manual, please call
TOLL FREE : 1-800-605-8610
or visit our web site at http://www.funai-corp.com
Audio/Video cables (WPZ0102TM015/ WPZ0102LTE01)
Owner’s Manual (1VMN22353)
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Table of Contents
Precautions
Laser Safety ...................................................................2
Important Safeguards ..................................................3
Location and Handling ....................................................4
Avoid the Hazards of Electrical Shock and Fire .............4
Warning of Dew Formation .............................................4
About Copyright ..............................................................4
Notice for Progressive Scan Outputs .............................4
Symbols Used in This Manual ........................................4
Maintenance ................................................................... 4
PrecautionsSetupFunctionsInformationEspañol
About the Media............................................................5
Playable Media ............................................................... 5
Unplayable Media ...........................................................5
Setup
Connections .................................................................. 6
Connection to a TV .........................................................6
Connection to an Audio System .....................................7
Front Panel Indicator and Rear Terminals .....................7
About the Remote Control ...........................................8
Remote Control ..............................................................8
Installing the Batteries for the Remote Control ..............8
Functions
Playback ........................................................................9
On-Screen Display ......................................................10
Search Function .........................................................10
Using Track Search ...................................................... 10
Using Title / Chapter Search ........................................10
Using Time Search ....................................................... 11
Marker Setup ................................................................ 11
Repeat / Random / Programmed Playback ..............12
Repeat Playback ..........................................................12
Repeat A-B Playback ...................................................12
Random Playback ........................................................12
Programmed Playback .................................................12
Special Settings .......................................................... 13
Subtitle Language .........................................................13
Audio Language ...........................................................13
Camera Angles .............................................................13
Black Level Setting ....................................................... 13
Stereo Sound Mode......................................................13
Virtual Surround ............................................................13
DVD Setup ...................................................................14
LANGUAGE Setting .....................................................14
DISPLAY Setting ..........................................................15
AUDIO Setting .............................................................. 15
PARENTAL Setting ......................................................16
OTHERS Setting ..........................................................16
Reset to the Default Setting
(Except for PARENTAL Setting) ...................................17
Information
Troubleshooting Guide ..............................................17
Specifications .............................................................18
Language Code List ................................................... 18
Limited Warranty ........................................................18
Español ........................................................................19
Quick Use Guide .........................................Back Cover
Precautions
WARNING
CAUTION:
Precautions
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lo
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep­tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
se the authority to operate this equipment if an unauthorized change or modification is made.
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
STARE INTO BEAM.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special wastes. Contact your council for details.
For Customer Use: Read carefully the information located at the bottom of this unit and enter below the Model No. and the Serial No. Retain this information for future reference.
Model No.
Serial No.
-2-
EN
IMPORTANT SAFEGUARDS
1) Read Instructions - All the safety and operating
instructions should be read before the product is operated.
2) Retain Instructions - The safety and operating
instructions should be retained for future reference.
3) Heed Warnings - All warnings on the product and in the
operating instructions should be adhered to.
4) Follow Instructions - All operating and use instructions
should be followed.
5) Cleaning - Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not
recommended by the product manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water
- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8) Accessories - Do not place this
product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9) A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10) Ventilation - Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the prod uct on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
11) Power Sources - This product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12) Grounding or Polarization - This product may be
equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13) Power-Cord Protection - Power-supply cords should
be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep tacles, and the point where they exit from the product.
14) Lightning - For added protection for this product during a
lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges.
-
15) Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16) Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
18) Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19) Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into
the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its
normal operation. e) If the product has been dropped or damaged in any
way. f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20) Replacement Parts - When replacement parts are
required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
21) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
22) Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
-
Precautions
-3-
EN
Location and Handling
Do not stand this unit up vertically. Install this unit in a hori­zontal and stable position. Do not place anything directly on top of this unit. Do not place this unit directly on top of the TV.
• Depending on the TV, noise or disturbance of the picture and/or sound may be generated if this unit is placed too close to your TV. In this case, please ensure enough space between your TV and this unit.
• Do not cover or place this unit in enclosed spaces to prevent excessive temperature build up.
Precautions
Do not place this unit in direct sunlight, or near heat sources.
• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
• Keep this unit away from strong magnetic objects.
• Do not place any object containing water or other liquids on this unit. In the event that liquid should enter the cabinet, unplug this unit and contact the retailer or an Authorized Service Center immediately.
Do not remove this unit cabinet. Touching parts inside the cabinet could result in electric shock and/or damage to this unit. For service and adjustment inside the cabinet, call a qualified dealer or an Authorized Service Center.
• Be sure to remove disc and unplug the AC power cord from the output before carrying this unit.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.
Warning of Dew Formation
Moisture may form inside this unit under the following conditions:
• Immediately after a heater is turned on.
• In a steamy or humid room.
• When this unit is suddenly moved from a cold to warm environment.
If moisture forms inside this unit, it may not operate properly or damage the disc. In such case, turn on the power and wait for more than 2 hours for the moisture to evaporate.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disas­sembly is prohibited.
Symbols Used in This Manual
The following symbols appear in some headings in this manual.
: Description refers to playback of DVD-Video discs.
: Description refers to playback of Audio CDs.
Maintenance
SERVICING
Please refer to relevant topics on the “Troubleshooting Guide” on page 17 before returning the unit.
• If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and please call our help line mentioned on the front page to locate an Authorized Service Center.
CLEANING THE CABINET
• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercial­ly available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analog records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you refer to the relevant sections and to “Troubleshooting Guide” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• When you handle a disc hold it by its edge and try not to touch the surface of the disc.
• Always store a disc in its protective case when it is not used.
Notice for Progressive Scan Outputs
Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 525 progressive scan output, it is recom­mended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this 525p DVD player, please contact our customer service center.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
-4-
EN
About the Media
is a trademark of DVD Format/Logo Licensing Corporation.
or
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1
Chapter 2
Chapter 3 Chapter 4
Example
Track 1 Track 2 Track 5
Track 6
Track 3
Track 4
Playable Media
Playable
discs
DVD-Video
*1, 2, 4, 6
DVD-R
DVD-RW
*1, 3, 4, 5, 6,
7, 9, 10
DVD+R
DVD+RW
*1, 3, 4, 5, 6,
8, 9, 10
Audio CD
*4, 6
CD-R
CD-RW
*4, 5, 6,
9, 10
Mark (logo) Region code
Recorded
signals
Digital video
(MPEG2)
Digital audio
Disc size
12 cm
or
8 cm
12 cm
or
8 cm
Disc types
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played
back.
*2:
Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers. *3: Discs recorded in the VR (Video Recording) format cannot be played back. *4: Scratched or stained discs may not be played back. *5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or
special properties of discs. *6: You can play back discs which bear the marks above. If you use non-standardized discs, this unit may not play them
back. Even if they are played back, the sound or video quality will be compromised. *7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder.
However, depending on the recording status of a disc, the disc may not be played back at all or normally (the picture
or sound may not be smooth, etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the
manual accompanying the DVD recorder. *8: Only the discs recorded in the video format and finalized can be played back. Unfinalized discs cannot be played
back. Depending on the recording status of a disc, the disc may not be played back at all. The picture or sound may
not be smooth, etc. *9: If the recorded portion of the disc is too small (smaller than 55mm across), it may not be played back. *10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
Precautions
Unplayable Media
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / DVD-Audio / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL / DVD-ROM for personal computers / CD-ROM for personal computers
On the following disc, the sound MAY NOT be heard.
Super Audio CD NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
Any other discs without compatibility indications
-5-
EN
AUDIO OUT
VIDEO
OUT
R
L
Y
AUDIO
OUT
R
L
L R
AUDIO IN
VIDEO IN
VIDEO
OUT
S-VIDEO IN
S-VIDEO
OUT
C
B
Y
C
R
COMPONENT
VIDEO IN
or
P
B
Y
P
R
VIDEO
OUT
Y
COMPONENT VIDEO OUT
CR/P
R
CB/P
B
Setup
Connections
If your TV has AUDIO/VIDEO input jacks, see the following instructions. If not, see the section “Connecting to RF Modulator” on the front page.
Connection to a TV
Setup
TV
Basic Audio
Audio cable
(supplied)
Method 1
Good picture
Video cable
(supplied)
S-Video cable (commercially
Method 2
Better picture
Method 3
Best picture
Component Video cable (commercially available)
available)
This unit
AUDIO OUT
(Analog)
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
Hint
Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy protection system.
If your TV is compatible with 525p (480p) progressive scanning and you want to enjoy that high quality picture;
You must select the connection Method 3 above and progressive scanning mode. To set the mode, set “PROGRESSIVE” to “ON” in SETUP menu, so that the “P-SCAN” indicator on the front panel lights up. See pages 14­15 for more details.
• When “PROGRESSIVE” is “ON”, video signals from the unit’s VIDEO OUT and S-VIDEO OUT jacks will be distorted or not be output at all.
If your TV is not compatible with progressive scanning;
Use this unit in interlace mode and set “PROGRESSIVE” to “OFF” either in SETUP menu or by pressing and holding
[PLAY B] on the front of the unit for more than 5 seconds, so that the “P-SCAN” indicator on the front panel lights off.
After you have completed connections;
Press the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual accompanying your TV.
INPUT MODES FOR COMMON TV BRANDS
Listed below are inputs for common brand name TV’s.
Admiral: AUX Curtis Mathis: LINE1, LINE2, 00, 90, 91, 92, 93 GE: INPUT, TV/VCR, 00, 90, 91, 92, 93 Hitachi: INPUT, AUX JVC: VIDEO, VIDEO1, VIDEO2, VIDEO3 Kenwood: AUX LXI-Series: 00 Magnavox: AUX CHANNEL
Panasonic: TV/VIDEO RCA: INPUT, TV/VCR, 00, 90, 91, 92, 93 Samsung: TV/VIDEO Sanyo: VIDEO Sharp: 00 Sony: VIDEO1, VIDEO2, VIDEO3 Toshiba: TV/GAME Zenith: 00
-6-
EN
Loading...
+ 14 hidden pages