Magnavox MRU4100, MX010 User Manual

32

Battery Installation

1. On the back of the remote,
push down on the tab and
lift the cover off.

2. Match the batteries to the +
and - marks inside the
battery case, then insert 2
AAA Alkaline batteries.

3. Press the battery cover
back into place.

Battery Saver

Your remote automatically turns
off if the buttons are depressed
more than 30 seconds. This will
save your batteries should your
remote get stuck in a place
where the buttons remain
depressed (e.g., between the
sofa cushions).

Code Saver

You will have up to 10 minutes to change the batteries in
your remote without losing codes you have programmed.
However, do not press any buttons until batteries are
installed in the remote. If buttons are pressed without
batteries in the remote, all codes will be lost.

Code Setup

The CODE SEARCH button is used to setup the
remote. You can either setup the remote using the code
for your brand of product, from the code tables, or you
can search through the library of codes until you find a
code that works for your product.

Setup

Introduction

Table of Contents

CHAN

+

MUTE

VOL

+

CC

CODE SEARCH

Congratulations on your purchase of a Magnavox
Universal TV Remote Control. Magnavox
Universal Remotes let you replace a broken or
lost remote or combine more than one remote into
one.

This remote control operates the common features
of most but not all models and brands of IR
Infrared Controlled TVs. This remote may
provide functions that are not available on your
TV. Some functions of your particular TV (e.g.
menu functions) may not be controlled by this
remote. In such cases, use the original remote
control for your equipment. Please use this manual
to become familiar with your Magnavox Universal
TV Remote. After you are familiar with your
remote the first thing you need to do is to install
batteries and setup your remote for your particular
TV brand.

Thank you for buying a Magnavox remote and we
hope it will give you many years of service.

Introduction ...................................................... 2

Setup ............................................................... 3

Battery Installation ....................................... 3

Battery Saver ...............................................3

Code Saver ................................................. 3

Code Setup ................................................. 3

Button Functions ............................................... 4

Code Entry .......................................................5

Direct Code Entry ........................................5

Code Search ............................................... 5

Code Identification Feature .......................... 6

Sleep Timer ...................................................... 6

Troubleshooting ................................................ 7

Instrucciones en Español ................................... 8

Code List ....................................................... 14

MRU4100-OM(MX010)_H14112A.pmd 10/12/2007, 3:47 PM2-3

54

Direct Code Entry

1. Press and hold the CODE SEARCH button until the
red indicator stays on, then release the CODE
SEARCH button.

2. Enter the 4 digit code from the code table. Note:
after a valid code entry, the red indicator turns off.
For an invalid code, the red indicator flashes.

3. With your device on, press CHANNEL UP. If the
device responds, no further programming is
required. Note: If some buttons do not operate your
equipment, try one of the other codes for your

brand.

Code Entry

Write your code down here for easy reference later.

Code

Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.G. PREV CHAN may be called RECALL,
or ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.G., your product must have PREV CHAN
ability for the PREV CHAN button to operate this
feature.

Button Functions

CHAN

+

MUTE

VOL

+

CC

1

2

3

4

5

6

7

8

9

ENTER

SLEEP

0

VOLUME UP/
DOWN Changes

the volume level of
the product,
normally the TV.

CHANNEL UP/
DOWN

Changes the
channels.

PREV CHAN

Returns to the
previously selected
channel.

SLEEP Turns off the
TV after a period of 1
to 99 minutes.

ENTER

Used after direct
channel number
entry to immediately
change to the
selected channel.

NUMBERS

Enter numbers for direct
channel selection. Some
products require Enter to
be pressed after channel
selection.

MUTE Turns off the
TV sound while the
picture remains.

Red Indicator

Lights when
any button is
pressed.

CC (Closed Caption)

TV Closed Caption
(if your TV has this
feature).

CODE
SEARCH

Used for setup

Programming with Code Search

If your TV does not respond after you have tried all the
codes for your brand, or if your brand is not listed, try
searching for your code by following the steps below.

1. Manually turn on the TV to be controlled.

2. Press and hold the CODE SEARCH button until the
red indicator stays on, then release the CODE
SEARCH button.

3. Press the CHANNEL UP button repeatedly (up to
300 times) until the device to be controlled changes
channel. The red indicator blinks off with each
button press. If you accidentally overshoot the
code required, press the CHANNEL DOWN button
to backtrack through the library until the device
changes channel. Pressing CHANNEL UP changes
direction to forward again.

4. Press and release MUTE to install the code.

Note: Code Search starts from the currently stored 4
digit number.

MRU4100-OM(MX010)_H14112A.pmd 10/12/2007, 3:47 PM4-5

76

Troubleshooting

Remote does not operate your TV.

• Program the remote with a new code.

• Install new batteries. (You might have to reprogram
your remote after installing new batteries.)

• Remote may not be compatible with your TV.

Remote does not operate some features of
your TV.

• Program remote with a new code.

• Remote may not be able to operate all features of
your TV or button names might be different than
your TV’s original remote.

Red Indicator blinks after you program a TV
code.

• Remote did not accept the code.

• Try to program the code again or try a different
code.

For help with setup, please call: 919-573-7854.

The manufacturer warrants that this product shall be free
from defects in material, workmanship and assembly,
under normal use, in accordance with the specifications
and warnings, for as long as you own this product. This
warranty extends only to the original purchaser of the
product, and is nontransferable. Defective products,
together with the dated proof of purchase, must be
returned to the place of purchase for repair or
replacement. THERE ARE NO OTHER EXPRESS
WARRANTIES. Incidental and consequential damages
are disclaimed where permitted by law. This warranty
gives you specific legal rights, and you may also have
other rights which vary from state to state.

Made in China. Quality Assured in USA.
Ledgewood, NJ 07852

Limited Lifetime Warranty

Sleep Timer

The SLEEP button operates the Sleep function of your
device providing it supports the Sleep function.
Alternatively, you can enable the remote to turn off
your TV after a period of 1 to 99 minutes as shown
below. This feature works even if your TV does not
have its own Sleep function.

1. Press and hold the CODE SEARCH button until the
red indicator stays on. Release the CODE SEARCH
button.

2. Press and release the SLEEP button (Note any
previously set Sleep timer is canceled at this point
and the remote returns to normal operation).

3. Press and release the numeric buttons (01-99) for
the time required. The red indicator blinks off to
indicate button press acceptance and remains off
after the second button press.

4. TV Sleep Timer now set.

5. Leave the Remote pointing towards the TV with an
unobstructed path.

To cancel the Sleep Timer, press and release the

POWER button or repeat Steps 1 and 2 above.

Code Identification Feature

The Code Identification Feature allows you to identify
the 4 digit library code stored under your device key. For
example, if you want to find out what 4 digit code is
stored under your TV device key, follow the five steps
below:

1. Press and hold the CODE SEARCH button until the
red indicator stays on, then release the CODE
SEARCH button. The red indicator blinks, then
stays lit.

2. Press and release the CODE SEARCH button again.
The indicator light blinks off.

3. To find the first digit for the code stored, press each
numeric key from 0-9 in turn. When the indicator
light blinks off the number you pressed is the first
digit for the code you are searching for.

4. To find the second digit, repeat step 3, this time
when the indicator light blinks off this is the second
digit.

5. Repeat step 3 to find the third and fourth digits.

Code Identification

MRU4100-OM(MX010)_H14112A.pmd 10/12/2007, 3:47 PM6-7