Magnavox 17MD255V User Manual

Download

Important Information

Important Safety Instructions

Supplied Accessories

Remote control

Functional Overview

Connections

Basic Operations

Watching TV

Menu Adjustment

Basic Operations DVD

Play Discs In Various Ways

Menu Setting DVD

MP3 Operations

Kodak Picture CD Playback

Troubleshooting

Technical Specifications

Warranty Page

2-3

5-6

10-11

12-17

18-23

24-29

30-34

37-38

Table of Contents

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ’’dangerous voltage’’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the product.

This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measure.

●

Reorient or relocate the receiving antenna.

●

Increase the separation between the equipment and receiver.

●

Correct the equipment into an outlet on a circuit different from that to which the receiver

is connected.

●

Consult the dealer or an experienced radio, TV technical for help.

●

Only shielded interface cable should be used.

Fcc Rf Interference Statement

NOTE:

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

WARNING: To reduce the risk of fire or electric shock, do not expose this Product to rain or moisture.

Important Information

page1

The present set has been designed and manufactured to assure personal safety. Improper use

can result in electric shock or fire hazard. The safeguards incorporated in the present unit will

protect you if you observe the following procedures in installing, using and servicing. The present

unit is fully transistorized and does not contain any element that can be repaired by the user.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

15. Repair - If any of the following conditions occurs, unplug the AC cord from the AC outlet, and

request a qualified service person to perform repairs.

a) When the AC cord or plug is damaged.

b) When a liquid was spilled on the product or when objects have fallen into the product.

c) When the product has been exposed to rain or water.

Important Safety Instructions

page2

d) When the product does not operate properly as described in the operating instructions. Do

not touch the controls other than those described in the operating instructions. Improper

adjustment of controls not described in the instructions can cause damage, which often

requires extensive adjustment work by a qualified technician.

e) When the product has been dropped or damaged.

f) When the product displays an abnormal condition. Any noticeable abnormality in the product

indicates that the product needs servicing.

16. Replacement parts - In case the product needs replacement parts, make sure that the service

person uses replacement parts specified by the manufacturer, or those with the same

characteristics and performance as the original parts. Use of unauthorized parts can result in

fire, electric shock and/or other danger.

17. The LCD panel used in this product is made of glass. Therefore, it can be broken when the

product is dropped or gets shock. Be careful not to be injured by glass pieces in case the

panel is broken.

18. The LCD panel is a product of very high technology with 2,949,120 thin film transistors, giving

you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a

fixed blue, green or red point. Please note that this does not affect your product’s performance.

Important Safety Instructions

page3

Make sure the following accessories are provided with the product.

Supplied Accessories

page4

17MD255V

17’’ LCD TV WITH BUILT IN DVD PLAYER

Power adapter

Warranty card

Quick setup guide

AAA batteries

User guide

Remote control

Insert supplied batteries via the battery compartment on the back of the remote control.

Make sure polarity matches the (+) and (-) marks inside the compartment.

Remote Control

page5

Inserting Batteries Into The Remote Control

●

Do not expose remote to liquids, direct sunlight or shock.

●

The remote control unit may not work properly if the remote sensor window of the Display is

under direct sunlight or strong lighting. In such case, change the angle of the lighting or Display,

or operate the remote control unit closer to the remote sensor window.

Cautions Regarding Remote Control Unit

●

Use the remote control by pointing it towards the remote

sensor on the TV. Objects between the remote control and

the sensor may disrupt operation.

●

Effective range is 20 feet but is dependant on what your

viewing angle is.

●

Range can also be affected by direct sunlight on the TV’s

sensor.

Using The Remote Control Unit

Remote Control

page6

POWER

Use to turn the unit on and off.

Number Buttons

Use to set the channel and to enter DVD chapter numbers.

CAPTION

Use to select close caption mode.

VOLUME+/-

Use to adjust the volume.

LAST

Press to return to the previous channel in normal viewing mode.

TV/DVD/AUX/PC

Use to bring up the AV signal source selection screen and use the / buttons to select between: TV, DVD,AV1-Video,AV1-S-Video,AV2Component, PC, and press the OK button to confirm.

SUBTITLE

Use to shift DVD subtitle language.

ANGLE

Use to shift DVD viewing angle.

REPEAT

Use to repeat the DVD playback.

WIDE

In DVD mode, use to set TV display mode.

SETUP

Use to bring up DVD setup menu.

RETURN

Return to the previous menu screen.

FF/FR

Use to play DVD fast forward/ backward.

STOP

Use to stop the DVD playback.

DVD MENU

Use to bring up the DVD root menu.

TV MENU

Use to bring up TV menu; and exits TV menu by pressing again.

CH+/-

Use to skip to the previous/next channel.

MUTE

Mute the sound.

AUTO

Auto adjustment for PC signals.

OPEN( )

Use to eject the disc being played in the disc slot, the main unit must be set to DVD status.

OSD

Use to bring up the DVD OnScreen-Display.

MPX

Use to select the sound multiplex mode. (See page 16.)

PAUSE

Use to pause the DVD playback.

Cursor Buttons

Use to navigate in menus.

Use to confirm your selections.

DVD TITLE

Use to bring up the DVD title menu.

PLAY

Use to begin the DVD playback.

PREV/NEXT

Use to skip to the previous/next chapter.

ZOOM

Use to zoom the DVD playback picture.

SLOW

Use to slow the DVD playback speed.

P. MODE

Use to shift DVD play mode.

REMAIN

Use to display the time of the DVD playback.

A. MODE

Use to shift the DVD playback audio mode.

AUDIO

Use to shift DVD audio language.

1) REMOTE SENSOR

2) POWER ON INDICATOR

3) STANDBY INDICATOR

4) TV/DVD/AUX/PC: Use to select the AV signal source between: TV, DVD,AV1-Video,AV1-S-Video,AV2Component and PC.

5) CH+/-: To skip to the previous/next channel.

6) VOLUME+/-: Use to adjust the volume.

7) POWER BUTTON: Use to turn the unit on and off.

8) DISC SLOT: Insert a DVD or CD disc to play under DVD status.

9) PAUSE: Use to pause the DVD playback.

10) STOP: Use to stop the DVD playback.

11) PLAY: Use to begin the DVD playback.

12) EJECT: Use to eject the disc being played in the disc slot, the main unit must be set to DVD status.

Functional Overview

page7

Front View

STOP

PLAY

EJECT

Slot-load

DVD Player

PAUSE

TV/DVD/AUX/PC

CH CH VOL VOL

123

45 67

10 11

PHONES

AUDIO

S-VIDEO

VIDEO

B / PB

DC IN

VGA

AV1 IN

AUDIO

R / PR

AUDIO

VIDEO

AV OUT

AV2 IN

PC IN

4 5 6

Rear View

1) AV1 IN (Composite Video,

S-Video and Audio In)

2) AV OUT (Composite Video

and Audio Out)

3) AV2 IN (Component Video and Audio In)

4) PC IN (VGA and Audio)

5) PHONES

6) DC IN (12 Volt)

Connections

page8

Computer

HDTV Receiver

PHONES

AUDIO

S-VIDEO

VIDEO

B / PB

DC IN

VGA

AV1 IN

AUDIO

R / PR

AUDIO

VIDEO

AV OUT

AV2 IN

VGA Audio Cable

1. CONNECT TO POWER

a. Connect the mini plug of the AC power

adapter to DC IN jack on the back of the 17MD255V.

b. Connect the power plug of the AC power

adapter to the power socket.

2. SYSTEM CONNECTIONS a. Using the antenna input: Connect the

antenna terminal from an antenna or cable/satellite receiver to the antenna input terminal on the 17MD255V; use the TV/DVD/AUX/PC button and the / buttons to set the 17MD255V’s signal source to "TV".

b. Using the AV1 RCA Video/Audio input:

Connect compatible AV equipment to the 17MD255V through the AV1 IN jacks on 17MD255V (Composite Video and Audio input jacks); use the TV/DVD/AUX/PC button and the / buttons to set the 17MD255V’s signal source to "AV1-Video".

c. Using the AV1 S-Video and RCA Audio

input: Connect AV equipment to the

17MD255V through the AV1 IN jacks on 17MD255V (S-Video and Audio input jacks); use the TV/DVD/AUX/PC button and the

/ buttons to set the 17MD255V s signal

source to AV1-S-Video .

d. Using the AV2 Component input: The AV2

input may be used for Progressive scan or HDTV inputs; use the TV/DVD/AUX/PC button and the / buttons to set the 17MD255V’s signal source to "AV2Component".

e. Using the VGA connector: Connect a PC

computer to the 17MD255V through the VGA socket on 17MD255V. The Miniplugged next to the VGA input is for audio associated with this type of signal. Use the TV/DVD/AUX/PC button and the / buttons to set the 17MD255V s signal source to PC-IN . 17MD255V monitor s native resolution for computer use is 1024x768.

f. Using the AV out, RCA Video/Audio

output: Connect the 17MD255V to another

TV Monitor through the AV OUT jacks on 17MD255V(Composite Video and Audio output jacks); now you can use the TV Monitor as an external monitor. Signals from the Antenna, AV1 and Internal DVD player will be available at this point.

1. Press POWER button on the front panel to

turn on the TV set. The STANDBY/ON

indicator lights up green.

2. If the STANDBY/ON indicator still lights up

red, press POWER on the remote control

to turn the TV set on.

Basic Operations

page9

Turning On The Power

1. Press POWER on the remote control, the

image on the screen disappears and the

STANDBY/ON indicator changes from

green to red.

NOTE: Small amounts of electric power is still

consumed even when the power is

turned off.

Turning Off The Power

By pressing the TV/DVD/AUX/PC on the TV

set and confirming by the OK button, you can

change the mode as follows:

TV/AV Mode Selection

TV/DVD/AUX/PC

CH CH VOL VOL

POWER

TV/DVD/

AUX/PC

TV DVD AV1-Video

PC AV2-Component AV1-S-Video

1. Press POWER button on the front panel to

turn on the TV set. The STANDBY/ON

indicator lights up green.

2. If the STANDBY/ON indicator still lights up

red, press POWER on the remote control

to turn the TV set on.

Watching TV

page10

Turning On The Power

1. Press POWER on the remote control, the

image on the screen disappears and the

STANDBY/ON indicator changes from

green to red.

NOTE: Weak electric power is still consumed

even when the power is turned off.

Turning Off The Power

1. Press CH+ to increase channel number.

2. Press CH- to decrease channel number.

NOTE: CH+/- on the TV set operates the

same as CH+/- on the remote unit.

CH+/- on the TV operates only in TV

mode.

CH+/-

You can change channels in several ways.

Using CH+/- on the remote unit

Simple Button Operations For

Changing Channels

TV/DVD/AUX/PC

CH CH VOL VOL

CH+/-

Using number buttons on the remote unit

Watching TV

page11

Press LAST to switch the currently tuned

channel to the previous tuned channel.

Press LAST again to switch back to the

currently tuned channel.

Select the channels directly by pressing the number buttons.

EXAMPLE:

To select a 1-digit channel (e.g. channel 2):

●

Press 2 .

To select a 2-digit channel (e.g. channel 12):

●

Press 1 ,followed by 2 .

Using Last On The Remote Unit

NUMBER

BUTTONS

LAST

Simple Button Operation For Changing Volume/Sound

Changing the volume

You can change the volume on the front panel or on the remote control unit.

VOLUME+/-

1. Press VOL+ to increase the volume.

2. Press VOL- to decrease the volume.

Using MUTE on the remote control

Press MUTE to mute the current sound output.

1. Press MUTE . ’’ ’’ will display on the screen.

2. Press MUTE again to cancel the mute.

MUTE

Press TV MENU to bring up the TV menu screen. Press / to select "Settings" and press to enter into the items below ’’Settings’’. NOTE: Only when in TV status, there is

"Settings"option. Make sure press TV MENU to exit TV menu screen before other operatings.

Menu Adjustment

page12

TV Tuner Adjustment

TV Source

This will help you to select the TV’s signal source.

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select "Settings" and press

to select "TV Tuner".

3. Press to enter "TV Tuner" menu.

4. Press / to select "TV Source".

5. Press / to select your desired TV source between Antenna and Cable; press

OK to return; press TV MENU to exit.

Automatic channel search

Channel auto search finds and memorizes all channels viewable in your area. Select one between ANTENNA and CABLE before this operation.

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select "Settings" and press to select "TV Tuner".

3. Press to enter "TV Tuner" menu.

4. Press / to select "Auto Search".

5. Press to begin the searching. Wait until the searching ends.

NOTE: The illustrations and on-screen

displays in this manual are for explanation purposes and may vary from the actual operations.

Channel skip

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select "Settings" and press to select "TV Tuner".

3. Press to enter "TV Tuner" menu.

4. Press / to select "Channel Skip".

5. Press / to select between "On" and "Off"; press OK to return; press TV MENU

to exit.

Current channel number selection

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select "Settings" and press to select "TV Tuner".

3. Press to enter "TV Tuner" menu.

4. Press / to select "Current Channel".

5. Press / to select a current channel number you want; press OK to return; press TV MENU to exit.

Menu Adjustment

page13

Password

1. Press TV MENU to bring up the TV menu

screen.

2. Press / to select "Settings" and press

to select "Content Blocking".

3. Press to enter "Content Blocking

(Password)" menu.

4. Press to select "Enter" and press to

enter the password.

5. Press / to select digit and press /

to change the selected digit.

6. Press to select "OK" and press OK to

check the password. Then there will be

"Change" and "Clear" under "Enter".

7. Press to select "Change" and press to

change the password.

8. Press / to select digit and press / to

change the selected digit.

9. Press to select "OK" and press OK to

confirm your change.

10. Press to select "Clear" and press to

clear the password; press OK to return;

press TV MENU to exit.

NOTE:The preset password is 071100.

Enter 071100 , there will be

ERROR displayed on the screen. _

Enter 071100 again, the menu for

changing password appears.

Content Blocking

Password

00000

Menu Adjustment

page14

Color

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’’Color’’.

4. Press / to adjust the picture color; press OK to return; press TV MENU to exit.

Sharpness

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’’Sharpness’’.

4. Press / to adjust the picture sharpness;

press OK to return; press TV MENU to exit.

Contrast

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’’Contrast’’.

4. Press / to adjust the picture contrast; press OK to return; press TV MENU to exit.

Brightness

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’’Brightness’’.

4. Press / to adjust the picture brightness; press OK to return; press TV MENU to exit.

Press TV MENU to bring up the TV menu

screen.

Press / to select ’’Picture’’ and press to

enter into below items.

Picture Adjustment

tint color temp

cool

16 16

Tint

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’Tint’’.

4. Press / to adjust the tint; press OK to return; press TV MENU to exit.

Color Temp

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Picture’’.

3. Press / to move to ’’Color Temp’’.

4. Press / to select the color temp among: Normal, Warm and Cool; press

OK to return; press TV MENU to exit.

NOTE: Only when in TV status, there is Tint

option.

Menu Adjustment

page15

Volume

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’Volume’’.

4. Press / to adjust the volume; press OK to return; press TV MENU to exit.

Press TV MENU to bring up the TV menu

screen.

Press / to select ’’Audio’’ and press to

enter into below items.

Audio Adjustment

mpx

mono

Bass

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’Bass’’.

4. Press / to adjust the bass weaker or stronger; press OK to return; press TV

MENU to exit.

Treble

To stress high frequency sound

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’Treble’’.

4. Press / to adjust the treble weaker or stronger; press OK to return; press TV

MENU to exit.

Balance

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’Balance’’.

4. Press / to adjust audio output between left and right speakers; press OK to return; press TV MENU to exit.

Mute

This function is to remove the sound.

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’Mute’’.

4. Press / to select ’’Off’’ or ’’On’’; press

OK to return; press TV MENU to exit.

MPX

This function is to select a MPX mode.

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Audio’’.

3. Press / to move to ’’MPX’’.

4. Press / to select a MPX mode, between: mono , stereo , and sap .

5. Press OK to return; press TV MENU to exit.

NOTE: 1. You can also use the MPX button

on the remote control to select a

MPX mode.

2. Only when in TV status, there is MPX option.

PC mode input format

In case of inputting the PC signal other than

above signals, ’’OUT OF RANGE’’ will display.

Menu Adjustment

page16

Window Adjustment

Press TV MENU to bring up the TV menu

screen.

Press / to select ’’Window’’ and press to

enter into below items.

display mode

Resolution

VGA

SVGA

XGA

WXGA

640

×480 640×480 640×480

800×600

1024×768 1024×768 1024×768

1280×768

60 70 75

60 72 75

Freq. (Hz)

Close Caption Mode

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Window’’.

3. Press / to move to ’’Close Caption Mode’’.

4. Press / to select close caption mode; press OK to return; press TV MENU to exit.

NOTE: You can also use the CAPTION

button on the remote control to select close caption mode.

Close Caption

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Window’’.

3. Press / to move to ’’Close Caption’’.

4. Press / to control close caption; press OK to return; press TV MENU to exit.

NOTE: In DVD, PC and COMPONENT Status,

there are only Display mode and H position options.

Display Mode

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Window’’.

3. Press / to move to ’’Display Mode’’.

4. Press / to select a display mode between:Fill All and Force 4:3; press OK to return; press TV MENU to exit.

H-Position

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Window’’.

3. Press / to move to ’’H-Position’’.

4. Press / to adjust the horizontal position of displayed image; press OK to return; press TV MENU to exit.

Menu Adjustment

page17

Press TV MENU to bring up the TV menu screen. Press / to select ’’Options’’ and press to enter into below items.

Options Adjustment

Back Light Adjust

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Options’’.

3. Press / to move to ’’Back Light Adjust’’.

4. Press / to adjust the back light; press

OK to return; press TV MENU to exit.

language

English

back light adjust

osd timeout

5 Sec

down for option settings

Language

It is used to set the menu language among: English, Fran ais and Espa ol.

1. Press / to select "Language " in "Option" menu.

2. Press / to adjust the language among:

English, Fran ais and Espa ol.

3. Press TV MENU to exit.

OSD Timeout

It is used to adjust the OSD timeout .

1. Press / to select "OSD Timeout " in "Option" menu.

2. Press / to adjust the "OSD Timeout " :

5sec 10sec 15sec 20sec 25sec 30sec

never

60sec 50sec 40sec

Reset

1. Press TV MENU to bring up the TV menu screen.

2. Press / to select ’’Options’’.

3. Press / to move to ’’Reset’’.

4. Press to reset all settings to factory setting.

From 5 to 60 second : the menu will

disappear automatically according to the

time you selected . Never : when you select the "Never" , the menu will not disappear automatically , you must press TV MENU to exit the LCD menu .

4. Press TV MENU to exit.

DVD

1. Press POWER to turn on the unit.

2. Press the TV/DVD/AUX/PC button on the remote control to bring up the AV signal source selection screen and use the / buttons to select "DVD", press the OK button to confirm.

3. Insert a disc into the disc slot, with the label side facing to yourself.

4. The unit begins to read the disc.

5. Press (PLAY) to play the disc.

AFTER STEP 4 IS FINISHED:

●

If playing a DVD, the TV screen shows DVD menu or title menu.

●

If playing a CD, press (PLAY), and the unit plays the disc according to the track numbers.

5. Stop playback.

Press ■ .

Play Discs

、

6. Press the button on the remote control to

remove the disc and turn off the unit.

●

You have to push "■" button twice to stop

playback of a DVD disc.

Pause

Press

●

To pause playback of a DVD while it is

playing, press .The unit enters step play

status. Each time you press , the

picture advances one frame.

●

Press to make playback pause.

Press (PLAY)to resume playback.

OSD

The On-Screen Display (OSD) contains many playback features.To see the Display, press the OSD button on the remote while a disc is playing. The picture being played will be zoomed out to the top of the screen. The Display appears under the zoomed picture. Use the or buttons on the remote to move through the different playback features in the Display.

When a playback feature is highlighted, press the (PLAY) button and the text box by the right side of it will be highlight.Use the or buttons on the remote to move through the choices displayed in the text box.

DVD

、

DVD

、

DVD

PAUSE

OSD

page18

Basic Operations (For DVD Player)

page19

Basic Operations (For DVD Player)

Remember, you can only access the Display

when you’re playing a disc. Also, the Display

features are only available if the disc was

created with that particular feature.

The invalid symbol " " appears on the screen

when you press a button that doesn’t have any

function. If one of the playback features is

"grayed out ",that Display feature isn’t available

for the disc you’re playing.

To make the Display disappear from the

screen, press OSD on the remote.

DVD discs have the following playback

features:Title, Chapter, Audio, Subtitle, Angle,

TT (Title) Time, CH (Chapter) Time, Repeat

and Time Display.

■ Select a Title

Some discs contain more than one title. Each

title is divided into chapters. To select a title:

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. If the Title icon on the Display isn’t

highlighted, use the or buttons to

highlight it.

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons on the remote to

enter a title number that you want to play.

Note: Some discs only have one title.

■ Select a Chapter

Because DVD discs use digital technology, a

title can be divided into chapters (similar to

tracks on a CD). You can skip to a specific

chapter by using the Chapter feature in the

Display.

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight the

Chapter icon.

WHEN PLAYING DVD

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons on the remote to

enter a chapter number that you want to

play.

Notes: The chapter feature won’t work if the

disc isn’t formatted with separate

chapters. You can also advance to the

next chapter by pressing on the

remote and go to the preceding

chapter by pressing on the remote.

■ Changing the Audio Language

If the disc was created with different language

tracks (recorded in different languages), you

can use the Display to temporarily change the

DVD player’s Audio Language setting.

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight the

Audio icon.

3. Press the (PLAY) button, the audio

languages appear on the screen.

4. Press the or buttons to move through

the audio languages that are available on

the disc.Press the (PLAY) button when the

audio language you want to use is highlighted.

5. To make the Display disappear, press the

OSD button on the remote.

Note: The language feature only works if the

disc was created with multiple audio tracks.

When you choose an audio language from the

Display, you only override the audio language

setting in the DVD player’s main menu

temporarily.

The audio language can also the changed

through the DVD player menu.

■ Selecting the Subtitle Language

If the disc was created with subtitles, you can

use the Display to change the Subtitle

language.

page20

Basic Operations (For DVD Player)

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight "TT

(Tile) Time" .

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons to enter an angle

number that you want to play.

■ Setting Chapter Time

You can skip to a specific chapter time by using

the Chapter Time feature in the Display.

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight "CH

(Chapter) Time" .

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons to enter an angle

number that you want to play.

■ Using the Repeat Feature

The default mode for the Repeat feature is off.

There are three Repeat options:

●

All - repeats the disc that is playing

●

Title - repeats the title that is playing

●

Chapter - repeats the chapter that is playing

To Use Repeat:

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight

"Repeat".

3. Press the (PLAY) button, the repeat

options appear.

4. Press the or buttons to move through

the repeat options. Press the (PLAY)

button when the repeat option you want to

use is highlighted.

5. The selected repeat option will loop

repeatedly until you turn Repeat off.

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight the

"Subtitle".

3. Press the (PLAY) button, the subtitle

languages appear.

4. Press the or buttons to move through

the subtitle languages that are available on

the disc.Press the (PLAY) button when the

subtitle language you want to use is highlighted.

5. To make the Display disappear, press the

OSD button on the remote.

Notes: Changing the subtitle language with the

Display will only affect the disc currently being

played. When the disc is removed or the player

is turned off, the subtitle language will revert to

the language setting specified through the DVD

player main menu.

The subtitle language can also be changed

through the DVD player menu.

■ Changing the Camera Angle

Some discs contain multiple angles of a

particular scene or sequence. When multiple

angles are available, to change the camera

angle:

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight "Angle".

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons to enter an angle

number that you want to play.

5. To make the Display disappear, press the

OSD button on the remote.

■ Setting Title Time

You can skip to a specific title time by using the

Title Time feature in the Display.

page21

Basic Operations (For DVD Player)

■ Setting Track Time

You can skipo to a specific track time by using the Track Time feature in the Display.

1. While the disc is playing, press OSD on the remote to bring up the Display.

2. Press the or buttons to highlight "Track Time" , while a disc is playing.

3. Press the (PLAY) button, the text box by the right side is now highlighted.

4. Use the number buttons on the remote to enter a track time that you want to play.

■ Using the Repeat Feature

The default mode for the Repeat feature is off. There are two Repeat options for CDs:

●

All - repeats the disc that is playing

●

Track - repeats the track that is playing

To use Repeat:

1. While the disc is playing, press OSD on the remote to bring up the Display.

2. Press the or buttons to highlight "Repeat" , while a disc is playing.

3. Press the (PLAY) button, the repeat options appears.

4. Press the or buttons to move through the repeat options. Press the (PLAY) button when the repeat option you want to use is highlighted.

5. The selected repeat option will loop repeatedly until you turn Repeat off.

■ Shifting the Displayed Time

Using the Time Display feature in the Display,

you can shift the time displayed on the screen,

between: Single (Track) Elapsed Time, Single

(Track) Remain Time, Total (Disc) Elapsed

Time, and Total (Disc) Remain Time.

How to Cancel Repeat:

There are three ways to cancel Repeat:

●

Press STOP twice.

●

Go to Repeat icon in the Display and select Off.

●

Eject the disc.

■ Shifting the Displayed Time

Using the Time Display feature in the Display, you can shift the time displayed on the screen, between: Title Elapsed Time, Title Remain Time, Chapter Elapsed Time, and Chapter Remain Time.

1. While the disc is playing, press OSD on the remote to bring upo the Display.

2. Press the or buttons to highlight "Time Disp".

3. Press the (PLAY) button, the time options appear.

4. Press the or buttons to move through the time options. Press the (PLAY) button

when

the option you want to use is highlighted.

5. To make the Display disappear, press the

OSD button on the remote.

WHEN PLAYING CD

CD discs have the following playback features: Track, Disc Time, Track Time, Repeat and Time Display.

■ Select a Specific Track

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight "Track" .

3. Press the (PLAY) button, the text box by the right side is now highlighted.

4. Use the number buttons on the remote to enter a track nunber that you want to play.

■ Setting Disc Time

You can skip to a specific disc time by using the Disc Time feature in the Display.

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight

"Disc Time", while a disc is playing.

3. Press the (PLAY) button, the text box by

the right side is now highlighted.

4. Use the number buttons on the remote to

enter a disc time that you want to play.

Volume Control

●

Press VOLUME on the TV or amplifier to

adjust the volume.

●

Press VOLUME on the remote control.

1. Press + to raise the volume.

2. Press - to lower the volume.

VOLUME+,-

DVD

、

DVD Menu Play

Some DVDs have title menus and chapter menus. Press (PLAY), the screen shows the menu.

Press or to skip to the next or previous

page. Select with number buttons or direction

buttons.

Example: select track 13.

1. Press to enter the next menu.

2. Press number buttons to select directly.

You can also select as follows:

1. Press to select track 13.

2. Press (PLAY) to start playing track 13.

Press DVD TITLE once to return to the title menu. Press DVD MENU once to return to the root menu.

12.

13.

14.

15.

12.

13.

14.

15.

Root Menu

11.

Root Menu

DVD

+10

page22

Basic Operations (For DVD Player)

1. While the disc is playing, press OSD on

the remote to bring up the Display.

2. Press the or buttons to highlight "Time

Disp" in the Display while a disc is playing.

3. Press the (PLAY) button, the time options

appears.

4. Press the or buttons to move through

the time options.Press the (PLAY) button when the option you want to use is highlighted.

5. To make the Display disappear, press the

OSD button on the remote.

Load a disc. Press number buttons to select

tracks after the unit finishes reading the disc.

1. If the track number isn’t over 10, just

push buttons 1-10.

Example: push 8 to select track 8.

The screen shows:

2. If the track number is over 10, press +10

once and a

button between 1-10.

Example: if you select track 12, press +10

once and

button 2 .

The screen shows:

Select with Number

Buttons

TRACK08/20 00:00

TRACK12/20 00:00

page23

Basic Operations (For DVD Player)

+10

Audio Mode

●

You may select a language from a multi-

language DVD.

●

You may select the right channel, left

channel, or stereooptions from a multichannel CD.

●

To select a language, press AUDIO .

The screen will show the following in order:

Different discs may differ in languages available.

●

To select audio channel option, press A.MODE , the screen shows the following in order:

AUDIO 1/2:AC-3 5.1CH

AUDIO 2/2:AC-3 5.1CH

DVD

、

DVD

MONO LEFT

MONO RIGHT

MIX-MONO

STEREO

AUDIO

A.MODE

page24

Play Discs In Various Ways

A.MODE

You may select one mode.

Notes:

●

Different discs differ in languages available.

Mute

When playing a disc, this function removes the

sound.

1. TO REMOVE SOUND

Press MUTE , the screen shows " ".

2. TO RESUME SOUND

Press MUTE again, to resume sound.

To select audio channel option when for CD

playback, press A.MODE . The screen will

show the following in order:

MONO LEFT

MONO RIGHT

MIX-MONO

STEREO

DVD

、

MUTE

A.MODE

1. While disc is playing, press to play in

fast-forward mode. Each time you press the

button, the screen shows the following in

order:

2. While disc is playing, press to play in

fast-reverse mode. Each time you press the

button, the screen shows the following in

order:

3. Press (PLAY) to switch to normal play

while in fast-forward or fast-reverse playing

mode.

Fast Play

When playing a disc, you can play it in fast-

forward or fast-reverse mode to find what you

want to view.

DVD

、

DVD OR CD

① 2X ② 4X ③ 8X ④ 16X ⑤ 32X ⑥

page25

Play Discs In Various Ways

Slow Play

Enjoy slow motion by the following the steps below.

1. Press SLOW to play in slow motion.

The screen shows the following in order:

DVD

2. Press (PLAY) to resume play at normal

speed.

DVD

1/4 1/8

1/41/81/16

1/2 1/16

1/2

Repeat Play

This function can be used to repeatedly play a

title, chapter, track, or a whole disc.

DVD

、

SLOW

REPEAT

Playing A Disc Repeatedly

You can repeat a title or chapter.

1. To repeat a chapter:

Press REPEAT , the screen will show:

2. To repeat a title:

Press REPEAT twice, the screen will

show:

3. To repeat all:

Press REPEAT third time, the screen

shows " ALL".

4. To remove "REPEAT" function:

Press REPEAT until " ALL"

disappears.

● You may repeat a track or an entire disc

according to the following steps.

1. To repeat a track:

Press REPEAT , the screen shows

" TRACK".

The unit plays the current track.

TITLE

CHAPTER

DVD

REPEAT

page26

Play Discs In Various Ways

REPEAT

2. To repeat a disc: Press REPEAT , the screen shows " ALL". The unit plays all the tracks on the disc.

3. To remove "REPEAT" function: Press REPEAT till " ALL" disappears.

ALL

TRACK

REPEAT

Zoom Play

This function can be used to watch a motion or motionless picture.

1. Press ZOOM during playback, the screen shows:

The picture is enlarged twice the size.

2. Press ZOOM again, the screen shows:

The picture is enlarged three times the size.

Note: The unit has six zoom levels:

3. Press , , , to move the enlarged

picture.

4. To resume the picture, press ZOOM until

the picture is in normal size.

DVD

2X,

1/4 .

3X, 4X, 1/2 , 1/3 , and

ZOOM

Select Subtitles

This operation works only with discs with

multiple subtitle languages recorded.

DVD

1. Press SUBTITLE repeatedly until the

desired language is selected.

The screen shows:

2. Remove the subtitle.

Press SUBTITLE until the screen shows

"TURN OFF SUBTITLE".

Notes:

●

For some discs, subtitles cannot be removed.

●

Different discs differ in the language of

subtitles.

●

If the subtitles of discs cannot be selected,

the screen shows " " when you press

SUBTITLE .

SUBTITLE01/03:ENGLISH

DVD

SUBTITLE

page27

Play Discs In Various Ways

Angles Select

Some discs have images with different viewing

angles, you may select among them. For

example, when you watch a running train, you

may watch it from the front, the left window or

the right window without stopping it.

Example:

A DVD has four viewing angles at your

option.

1. Press ANGLE to select ANGLE1.

2. Press ANGLE to select other angles , the

screen shows respectively:

3. To resume normal playback, press ANGLE

to select original angle.

2/4 (select ANGLE2)

3/4 (select ANGLE3)

4/4 (select ANGLE4)

1/4

DVD

ANGLE

page28

Play Discs In Various Ways

Program Play

To use the program playback feature, you must enter the order in which you want the titles (and chapters) on the DVD or the tracks on the CD to play by creating a program.

1. Press P.MODE unt

il the screen shows:

2. Use the number buttons on the remote to enter the title (and chapter) you want to play first. The title (and chapter) number you entered appears in the box. For example: Enter Chapter 1 in Title 8, the screen shows:

3. The cursor jumps to the next spot in the program list section. Make sure the box is highlighted and enter your next track.

4.Continue adding title (and chapter) until your

program is complete. You can play your program by highlighting START and press PLAY .

Note: If you want to program more than 10

titles (and chapters), highlight NEXT and press PLAY to go to the next page. Proceed to program 11-20 in the

same way titles 1-10 were programmed.

5. To remove program playback, press the

STOP button twice during the program play.

DVD CD

PROGRAM: TT(20)/CH (--) 01 TT:_ _ CH:_ _ 06 TT:_ _ CH:_ _ 02 TT:_ _ CH:_ _ 07 TT:_ _ CH:_ _ 03 TT:_ _ CH:_ _ 08 TT:_ _ CH:_ _ 04 TT:_ _ CH:_ _ 09 TT:_ _ CH:_ _ 05 TT:_ _ CH:_ _ 10 TT:_ _ CH:_ _

EXIT NEXT

PROGRAM: TT(20)/CH (--) 01 TT:0 8 CH:0 1 06 TT:_ _ CH:_ _ 02 TT:_ _ CH:_ _ 07 TT:_ _ CH:_ _ 03 TT:_ _ CH:_ _ 08 TT:_ _ CH:_ _ 04 TT:_ _ CH:_ _ 09 TT:_ _ CH:_ _ 05 TT:_ _ CH:_ _ 10 TT:_ _ CH:_ _

EXIT START NEXT

DVD

P.MODE

1. Press P.MODE

until t

he screen shows:

2. Use the number buttons on the remote to

enter the track number you want to play first.

The track number entered appears in the box.

The example: To program track 8 of a CD to

play first, enter 8, and the screen shows:

3. The cursor jumps to the next spot in the

program list section. Make sure the box is

highlighted and enter your next track.

4. Continue adding tracks until your program

is complete. You can play your program by

highlighting START and press PLAY .

Note: If you want to program more than 10

tracks, highlight NEXT and press

PLAY to go to next page. Program 11-

20 in the same way 1-10 were

programmed.

5. To remove program playback, press the STOP button during the program play.

PROGRAM: TRACK (01-20) 01 _ _ 06 _ _ 02 _ _ 07 _ _ 03 _ _ 08 _ _ 04 _ _ 09 _ _ 05 _ _ 10 _ _

EXIT NEXT

PROGRAM: TRACK (01-20) 01 08 06 _ _ 02 _ _ 07 _ _ 03 _ _ 08 _ _ 04 _ _ 09 _ _ 05 _ _ 10 _ _

EXIT START NEXT

page29

Play Discs In Various Ways

1. Press P.MODE to select shuffle or

random play mode when a disc is playing.

The screen shows:

2. Shuffle or random play will begin.

3. Remove shuffle or random play.

●

When playing a DVD disc, press ■ twice.

●

When playing a CD disc, press ■ twice.

Shuffle (Random) Play

The unit can play DVD chapters or audio

tracks in random order.

The order is different each time.

DVD CD

SHUFFLE RANDOMOR

P.MOD

SETUP

page30

Menu Setting DVD

According to the recorded information and

external equipment, set the following functions

for the player to obtain the best playing

status.

1.Press SETUP to set options in the main menu.

2. Press direction buttons ( or ) to select

and press (PLAY) to confirm.

Example: Select "Audio Setup" and do some

setup.

●

Press direction button to highlight "Audio

Setup", press (PLAY) to enter "Audio

Setup Page".

The main menu appears on the screen, with icons across the top of the screen, illustrating General Setup, Audio Setup, Preference, Password Setup, and Exit Setup. The screen shows:

--Setup Menu--Main page --

General Setup

Audio Setup

Preferences

Password Setup

Exit Setup

Go To General Setup Page

●

Press direction buttons , to select "LMono".

The screen shows:

●

Press direction buttons ( or ) to highlight "Dolby Digital Setup", and press (PLAY) to enter "Dolby Digital Setup" Page. The screen shows the submenu for your selection.

The screen shows:

-- Audio Setup Page --

Speaker Setup

Dolby Digital Setup

Channel Equalizer

3D Processing

Main Page

Go To Speaker Setup Page

--Dolby Digital Setup--

Dual Mono STR Stereo

L-Mono

R-Mono

Mix-Mono

D.R.C

Audio Setup

--Dolby Digital Setup--

Dual Mono STR Stereo

L-Mono

R-Mono

Mix-Mono

D.R.C

Audio Setup

page31

Menu Setting DVD

3. Exit setup menu.

●

Press the direction button to exit from

"Dual Mono".

●

Press the direction button to exit from

"Dolby Digital Setup".

●

Press the direction button to highlight

"Main Page" and press (PLAY). The

screen shows:

●

Press the direction button to highlight "Exit Setup" and press (PLAY) to exit setup menu completely.

NOTE:You can also keep pressing the

direction button until the cursor is moved to the last icon illustrating Exit, then press the (PLAY) button to exit setup menu completely.

Setup Page -- Main Page

General Setup

Audio Setup

Preferences

Password Setup

Exit Setup

Go To Audio setup Page

--Dolby Digital Setup--

Dual Mono L Stereo

L-Mono

R-Mono

Mix-Mono

D.R.C

Audio Setup

●

Press (PLAY) to confirm your selection. Set "Dual Mono" in "Dolby Digital Setup" to "L-Mono".

The sereen shows:

General Setup

The setting structure is :

-- General Setup Page --

TV Display Wide Normal/PS

Normal/LB Wide

OSD Lang ENG English

Fran ais Espa ol

Captions On On

Off

Screen Save On On

Off

Main Page

■ TV DISPLAY

1. NORMAL/PS This is selected when the unit is connected to a normal TV. Wide-screen images are shown on the screen, but with some parts cut automatically.

2. NORMAL/LB

This is selected when the unit is connected

to a normal TV. Wide-screen images are

shown on the screen with black bars on the

top and bottom of the screen.

3. WIDE

This is selected when the unit is

connected to a wide-screen TV.

NOTE: You can use the WIDE button on the

remote control to set TV display mode.

page32

Menu Setting DVD

■ OSD LANGUAGE

●

English

The OSD is in English.

●

Fran ais

The OSD is in France.

●

Espa ol

The OSD is in Spanish.

■ CAPTIONS

●

Subtitles are shown.

●

OFF

Subtitles are hidden.

■ SCREEN SAVER

The screen saver image appears when the unit stops or the image is frozen for a few minutes. The screen saver prevents damage to the TV screen.

●

ON: Start the screen saver.

●

OFF: Remove the screen saver.

Audio Setup

The setting structure is:

- - Audio Setup Page - -

Speaker Setup

Dolby Digital Setup

Channel Equalizer

3D Processing

Main Page

■ SPEAKER SETUP

The setting structure is:

●

Lt/Rt A disc recorded multi channel soundtrack, the output signal will be incorported to left and right channel.

●

STEREO A disc recorded multi channel soundtrack, the output signal will be incorported to stereo.

●

DUAL MONO This is the output mode of the L and R signals of the set audio output. If it is set to "MIX-MONO", the function only works when the DVD being played is 5.1-channel.

●

DYNAMIC

This is selected to adjust linear compression rate to obtain the different compression results of the signals.

■ DOLBY DIGITAL SETUP

The setting structure is:

FULL 3/4 2/4 1/4 OFF

- - Speaker Setup Page - -

Downmix STR Lt/Rt

Stereo

Audio Setup

- - Dolby Digital Setup - -

Dual Mono STR Stereo

L-Mono

R-Mono

Mix-Mono

Dynamic

Audio Setup

■ EQUALIZER

This will help you to select graphic equalizer patterns according to the genre of the music being played,and adjust the equalizer.

The setting structure is:

You can select music category by pressing the direction buttons and confirm by pressing the PLAY button.

●

EQ TYPE

- - Channel Equalizer - -

EQ Type None None

Rock

Pop Live Dance Techno Classic Soft

Audio Setup

page33

Menu Setting DVD

■ 3D PROCESSING

The setting structure is:

- - 3D Processing Page - -

V SURR Off On

Off

Reverb Mode Off Off

Concert Living Room Hall Bathroom Cave Arena Church

Audio Setup

●

V SURR

Use to turn the above function off.

●

REVERB MODE

Use to select a Reverb Mode which you want.

The setting structure is :

■

PASSWORD MODE

●

ON: The password function is on and

"PARENTAL" is dim and cannot be

selected.

●

OFF: The password is locked,

"PARENTAL" can be selected.

■

PASSWORD CHANGE

Select this to adapt the code, the screen shows:

Password Setup

Enter a password according to the screen.

Note: The password is automatically

factory set to 99999.

- - Password Setup Page - -

PW Mode Off On

Off Password Change Main Page

Old Password

New Password

Confirm PWD

page34

Menu Setting DVD

The setting structure is :

Preferences

- - Preference Page - -

Audio ENG English

French Spanish Chinese Japanese

Subtitle ENG English

French Spanish Chinese Japanese Off

Disc Menu ENG English

French Spanish Chinese Japanese

Parental 08 1 KID SAFE

2 G 3 PG 4 PG 13 5 PGR 6 R 7 NC17 8 ADULT

Default Reset

Main Page

■ LANGUAGE SELECTION If a language mentioned above is recorded on the disc, you can select sound, subtitles or disc menu languages. If not, the language recorded on the disc is shown.

■ PARENTAL LOCK When playing a disc with parental lock function, you may select an age control grade according to the rating your desire. Example: If "PG" is selected, you cannot play DVD video discs rated higher than the PG grade.

■ DEFAULT >> RESET Each function setting returns to the initial status in the factory if you select this option. Note:

●

"PREFERENCES" can only be selected when

password is OFF when the unit is in stop mode.

page35

MP3 Operations

■

SELECT TRACKS WITH

NUMBER BUTTONS

1. Insert a disc, the unit will search disc information. The TV screen displays main menu.

2.Press direction key to select song

folder. Press (PLAY) to confirm selection. Example: Select MP3-02, the TV screen displays.

3. Press direction buttons to select a song. Press (PLAY) button to start playback.

4. Press or button to select other tracks in stop mode.

5. In stop mode, select the folder icon (UP

DIR 1) on the left side, then press (PLAY) button to return to the main menu.

6. Press or to play previous or next

songs.

■

OTHER FUNCTIONS

During playback of MP3 discs, the unit

features mute, volume control, and repeat

play. Operations are the same as CD.

00:00 00:00

001/016 FOLDER

.. wave-11 wave-12 wave-13 wave-14 wave-15

00:00 00:00

001/012 FOLDER

CD01 CD02 CD03 CD04 CD05 CD06

\CD02\

Zoom

We provide both ZOOM in/out and Zoom pan function for the pictures. The "ZOOM" key is used to turn on or off this function. When this mode is on, any picture will be displayed at the last ratio selected by the user. A message on the screen will indicate the current Zoom ratio.

If zoom mode is on, "FF" and "FR" keys are used to control the ratio of zoom in/out. With ZOOM mode off, a picture is scaled to fit the TV screen.

Notes: During ZOOM function, slideshow transition and image rotation are disabled. TO cancel the ZOOM function, press the ZOOM key again and resume the slideshow.

Digest

The "MENU" or "STOP" key is used to display thumbnail size pictures. After it is enabled, up to 12 scaleddown thumbnail pictures will be displayed on the screen. The "NEXT" and "PREV" keys can be used to display the next/prev nine pictures in the the Kodak Picture CD.

You can select any of the nine displayed thumbnails by using the Arrow Keys and pressing the "PLAY" key. The thumbnail will be enlarged to fit the TV screen and the slide show will statr. If you desire to display an image indefinitely, press the PAUSE key. To view the Next or Previous picture press NEXT or PREVIOUS keys. To resume the slideshow press the PLAY key.

IMPORTANT NOTE: Quality of pictures displayed on the screen is highly dependent on the viewing device.

A Kodak Picture CD has the size and shape of a regular CD. You can order a KODAK Picture CD simply by checking the box on the photofinishing envelope when you drop off a roll of film (35 mm or Advanced Photo System (APS) color print film) at the time of processing in photo processing outlet displaying "Kodak Picture CD"sign. When your order is returned, you receive your prints, negatives, and your full roll of pictures safely stored on your KODAK Picture CD. Each KODAK Picture CD brings you the tools to enhance, share and manage your pictures on your computer. Now, you can playback Kodak Picture CDs on XXX DVD players and view your pictures on your TV in the comfort of your living room.

Playing back your Kodak Picture CD

The new feature enables the decoding of JPEG files from a Kodak Picture CD disk.

Playback modes

Normal

When a Kodak Picture CD is inserted on a player an automatic slide show is launched. Each picture in the Kodak Picture CD will be displayed consecutively in a slide-show fashion and will be scaled to fit in the TV screen. Twelve slideshow transition modes are provided, use "PLAY MODE" key to select.Select transition mode prior to start of slideshow if one mode is desired for the entire show.

Customer can set transition effects for each picture in a slideshow by using the "PLAY MODE" functions while viewing a slideshow.The last transition mode selected will be used in any future slideshows. To display an image indefinitely, press the PAUSE key. To view the Next or Previous picture press NEXT or PREVIOUS keys. To resume the slideshow press the PLAY key.

Image Rotation

There are four modes to rotate a picture:"Invert", "Mirror", "Left", and "Right". These operations are allowed only when a picture is being displayed normally and will be cancelled automatically when a new picture is displayed.The arrow key is used to select the diferent rotation modes:

Up Down Left Right

-Invert/Normal

-Mirror/Normal

-Turn left

-Turn right

Mode 0: no special transition effect (by default) Mode 1: wipe from top to bottom Mode 2: wipe from bottom to top Mode 3: wipe from left to right Mode 4: wipe from right to left Mode 5: wipe from left top to right bottom Mode 6: wipe from right top to left bottom Mode 7: wipe from left bottom to right top

Mode 8: wipe from right bottom to left top Mode 9: wipe from center to top/bottom Mode 10: wipe from center to left/right Mode 11: wipe from top/bottom to center Mode 12: wipe from left/right to center Mode 13: horizontal blinds Mode 14: vertical blind Mode 15: wipe from edge to center Mode 16: random

page36

Kodak Picture CD Playback

Troubleshooting

Watching TV

page37

Please check the following items before asking for repair service.

Symptom

Neither picture nor sound.

Picture is OK, but no sound.

Sound is OK, but no color.

The picture is overlapped image.

Picture has ’’snow noise ’’.

Stripes on picture.

Bad stereo or SAP sound.

Remote control does not work.

’’Out Of Range’’ appears on the screen.

’’No Signal’’ appears on the screen.

Image is not clear in PC mode.

Image is not centered.

Check Items

●

Check the contact of sockets is all right.

●

Check the TV main power is on.

●

Check the volume control is set to minimum or mute.

●

Check the color control and adjust it properly.

●

Check the programme is in color or in black & white.

●

Check the antenna is installed correctly and if not, adjust the antenna toward the broadcasting station.

●

Check the ’’FINE TUNE ’’is set up correctly and if not, adjust the fine tuning properly.

●

Check the antenna or its connection is correct and if not, correct the antenna fault or connection cable fault.

●

Check if car traffic or neon sign disturbs the sound effect.

●

Check the susceptible interference by other electronic devices such as radio and television and keep magnetic or electronic devices away from the TV.

●

Long distance from the station or other radio waves can generate bad sound. Reception. If so, change the mode to Mono.

●

Check if the batteries in the Remote control die.

●

Check if any object between IR sensor of the TV and the Remote control does not obstruct.

●

Check the resolution and frequency of your PC. Then, adjust them to optimum condition for LCD TV: 1280X768 and 60Hz.

●

Refer to the table of PC mode input format indicated on page 17. (Not being registered resolution and frequency on the table won’t be

displayed.)

●

Ensure that the signal cable is firmly connected to PC and TV.

●

Adjust the PHASE control. (Refer to the PICTURE ADJUSTMENT.)

●

Adjust the H-POSITION, and IMAGE SIZE Control. (Refer to the WINDOW ADJUSTMENT.)

No sound

●

Check if the unit is connected securely.

●

Make sure the TV or amplifier is working properly.

●

Make sure the amplifier is set to receive DVD

signal output.

Bad sound quality

●

Make sure the audio output mode is set correctly.

●

Make sure the audio connection between the

unit and amplifier is in place.

No image

●

Check if the unit is connected securely.

●

Make sure the TV is working properly.

●

Make sure the color system is set correctly.

This product incorporates copyright protection technology that is protected by method claims of

certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology must be authorized by

Macrovision Corporation, and is intended for home and other limited viewing uses only unless

otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is

prohibited.

●

Remove barriers between the remote control

and the unit.

●

Point the remote control at the remote control

sensor of the unit.

●

Replace the batteries with new ones.

Remote control does not work

●

Disconnect the power plug and insert it into the

wall outlet again.

The unit doesn’t operate

normally

●

There is no disc in the unit.

●

Put the disc on the disc tray properly with the

label side up.

●

Clean the disc.

●

Moisture has condensed in the unit. Remove

the disc and leave the unit on for about an hour.

Disc cannot be played

If you experience the following problems while using the unit, this troubleshooting guide can help you.

page38

Troubleshooting

Watching DVD

This manual is only for your reference, any change to the design and specifications will not be advised.

page39

Technical Specifications

LCD

●

PANEL 17’’ WIDE TFT LCD

●

RESOLUTION 1280 X 768 X RGB

●

ACTIVE AREA (mm) 370 X 222

●

VIEWING ANGLE (¡,H/V) 176/176

DIMENSION

●

WITH STAND (mm) 543 X 383 X 167

●

WITHOUT STAND (mm) 543 X 309 X 85

●

WEIGHT (WITHOUT ACCESSORIES) 8.676kg

TV-FUNCTION

●

TV STANDARD NTSC

●

TUNING SYSTEM ELECTRIC TUNING SYSTEM

●

FREQUENCY RANGE VHF/UHF

●

STEREO MTS + SAP

●

CATV 125 CHANNELS

SOUND

●

SOUND OUTPUT 4W + 4W

TERMINALS

●

AV IN VIDEO, S-VIDEO, AUDIO L&R

●

COMPONENT Y, Pb (Cb), Pr (Cr)

●

MONITOR OUT VIDEO OUT

●

HEADPHONE 3.5mm STEREO MINI-JACK

●

PC IN D-SUB 15PIN RGB IN

●

ANTENNA IN F-TYPE

DVD

●

Applicable disc DVD/CD-R/CD-RW/CD/MP3/Picture CD

Power adapter

●

Output DC 12Volt, 5 Ampere

●

Input 110~240Volt

●

Power consumption (TV) 45 Watt

●

Power consumption (DVD) ≤60 Watt

page40

Warranty Page

Ninety (90) Days Free Product Exchange

MAGNAVOX warrants this product against defect in

material or workmanship, subject to any conditions set forth as follows:

PROOF OF PURCHASE:

You must have proof of the date of purchase to exchange the product. A sales receipt or other document showing the product and the date that you purchased the product as well as the authorized retailer included, is considered such proof.

COVERAGE:

Warranty coverage begins the day you buy the product. For a period of ninety (90) days from the date of purchase, if the product is determined to be defective, Magnavox will exchange the defective product with a new or renewed product, at its option, at no charge. The replacement product is covered only for the warranty period of the original product. When the warranty on the original product expires, the warranty on all replaced products also expires. When it is necessary for you to ship the product to Magnavox for exchange, you will pay the shipping cost for shipment to Magnavox. Magnavox will pay the shipping costs when returning a product to you.

Note: The exchange model supplied will be the most comparable one in Magnavox current inventory. Shipping of your product to Magnavox implies intent to follow the specified requirements of the warranty and exchange program. Product received by Magnavox cannot be returned. Replacement product can only be sent if all warranty requirements are met. Failure to follow all requirements can result in delay of exchange process.

EXCLUDED FROM WARRANTY COVERAGE

Your warranty does not cover:

Shipping charges to return defective product. Labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. Product repair and/or part replacement because of improper installation, connections to improper voltage supply, abuse, neglect, misuse, accident, unauthorized repair or other cause not within the control of Magnavox. A product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications. Damage occurring to product during shipping when improperly packaged or cost associated with packaging.

Product lost in shipment and no signature verification of

receipt can be provided. A product used for commercial or institutional purposes (including but not limited to rental purposes). Product sold AS IS or RENEWED.

WHERE WARRANTY EXCHANGE IS AVAILABLE:

Exchange is available in all countries where Magnavox officially distributes the product. In countries where Magnavox does not distribute the product, the local Magnavox organization will attempt to exchange the product, although there may be a delay if the appropriate product is not readily available or special customs processes are implied.

FOR EXCHANGE IN THE U.S.A., PUERTO RICO, OR U.S. VIRGIN ISLANDS

Contact Magnavox Customer Care Center at: 1-800-705-2000

FPR EXCHANGE IN CANADA...

1-800-661-6162 (French Speaking) 1-800-705-2000 (English or Spanish Speaking)

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CONSUMER. MAGNAVOX SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICALBE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMTIED IN DURATION TO THE DRUATION OF THIS WARRANTY.

Some states do not allow the exclusions or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. In addition, if you enter into a service contract agreement with the MAGNAVOX partnership within ninety (90) days of the date of sale, the limitation on how long an implied warranty lasts does not apply.

This warranty gives you specific legal rights. You may have other rights which vary from state/province to

state/province.

EL6578E001 / 01-04

Magnavox, P.O. Box 520890, Miami, FL 33152 (402) 536-4171

17MD255V

17’’ LCD TV WITH BUILT IN DVD PLAYER

Magnavox 17MD255V User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual