Magnasphere MSS-330S, MSS-321S, MSS-320S, MSS-312S, MSS-311S Installation Instructions
...
MAGNASPHERE MSS-300S SERIES INSTALLATION INSTRUCTIONS: All Models of MSS300S-Series
Required Tools and Components
Provided by Manufacturer (per module set)
1 MSS-3XXS switch module
1 MSS-3XXS magnet module
Power drill
#36 Drill Bit or 7/64
4 #8 (x7/8" MIN) Flat Head Screws
Provided by Installer
24" (60cm)
MSS-3XXS
ARMORED
4x #8 FLAT HEAD
Installation Plan & Switch Orientation
SWITCH MODULE
MAGNET MODULE
Specifications
Max Current: 0.25 A Resistive
Max Voltage: 30 VDC
Max Power: .25 W Resistive
Suitable for Indoor and Outdoor use, for
U.S. and Canadian applications. The
Magnasphere MSS-3XXS series is
intended to be connected to a UL Listed
compatible control panel for US
applications and a ULC Listed compatible
control panel for Canadian applications.
CONTACT STATE SHOWN WITH MAGNET IN PLACE
OPEN
LOOP
OPEN
LOOP
MODEL MSS-303S
OPEN
LOOP
BLK
BLK
WHT
WHT
RED
RED
Triple loop capacity
‡ See p.2 for optional embedded
resistor schemes
BEST PLACEMENT
CONTACT STATE SHOWN WITH MAGNET IN PLACE
CLOSED
LOOP
CLOSED
LOOP
MODEL MSS-330S
CLOSED
LOOP
WHT
WHT
NOMENCLATURE
Surface mount
# of closed loops
MSS - 3 X X S-[‡]
# of open loops
BLK
BLK
RED
RED
Note:
Modules are
sensitive in
one direction.
Logos indicate
the proper
orientation as
illustrated.
Note:
This orientation will
reduce the "MAX GAP"
2"
(51mm)
and should be tested
for function.
Installation:
The 3xxS should be mounted close to the latch side of the door for
optimal performance. In order to meet UL 681 requirements, contact
.3 (7 mm)
shall be installed so door cannot be opened more than 2 inches without
causing an alarm. Intended for operating gaps of up to 5/16” (8mm).
Ensure that the modules are well aligned. When synchronous switching
of the contacts is important, position modules to operate as depicted.
Hold the switch module in position and drill one pilot hole; drive the #8
screw in until the module is seated. Repeat for the second hole. Repeat
these steps for the magnet module to insure accurate positioning.
Wire the switch according to the schematic. Check the operation of the
installed switch
Patents #5977873, #RE39731, #6506987, #6303845,
#6603378 & Other Patents Pending
05-2018 MSS-300S-INST REV. C
MAGNASPHERE N22 W22931 Nancys Ct. Ste 3, Waukesha, WI 53186 tel 262.347.0711 fax 262.347.0710 www.magnasphere.com
.
1.5"
(38mm)
.3" (7 mm)
MAX GAP
1/2"
(12.7mm)
*
1"
(25.4mm)
MAGNASPHERE MSS-300S SERIES INSTALLATION INSTRUCTIONS: Base Models
and Resistor-Embedded Models of MSS-300S-Series
P2
Schematics: All Base Model Infixes
CONTACT STATE SHOWN WITH MAGNET IN PLACE
OPEN
BLK
LOOP
BLK
OPEN
WHT
LOOP
WHT
MODEL MSS-303S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-312S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
OPEN
RED
LOOP
RED
CLOSED
BLK
LOOP
BLK
OPEN
WHT
LOOP
WHT
OPEN
RED
LOOP
RED
OPEN
BLK
LOOP
BLK
OPEN
WHT
LOOP
WHT
MODEL MSS-302S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-301S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-330S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-320S
End-Of-Line Resistor Standard Models ( -### suffix)
CONTACT FORM DEFINED BY INFIX
OPEN
BLK
LOOP
BLK
3 CIRCUIT POSITION KEY
CONTACT FORM DEFINED BY INFIX
CLOSED
BLK
LOOP
BLK
CLOSED
WHT
LOOP
WHT
OPEN
RED
LOOP
RED
CLOSED
BLK
LOOP
BLK
CLOSED
WHT
LOOP
WHT
MSS-3##S-001
CONTACT FORM DEFINED BY INFIX
MSS-3##S-002
1kΩ
1kΩ
Circuit
BLK
A
BLK
Circuit
WHT
B
WHT
Circuit
RED
C
RED
Circuit
BLK
1kΩ
A
BLK
Circuit
WHT
B
WHT
Circuit
RED
C
RED
Circuit
BLK
1kΩ
A
BLK
Circuit
WHT
1kΩ
B
WHT
Circuit
RED
C
RED
CONTACT FORM DEFINED BY INFIX
Circuit
BLK
BLK
Circuit
WHT
WHT
2 CIRCUIT POSITION KEY
MSS-3##S-001:
Series & Parallel 1k
resistors on circuit A.
One instance shown at
right:
MSS-3##S-002:
Series & Parallel 1k
resistors on circuit A,
Series 1k resistor on
Circuit B. One instance
shown at right:
A
B
CONTACT FORM DEFINED BY INFIX
Circuit
BLK
BLK
1 CIRCUIT POSITION KEY
CONTACT STATE SHOWN WITH MAGNET IN PLACE
CLOSED
BLK
1kΩ
1kΩ
MODEL MSS-321S-001
CONTACT STATE SHOWN WITH MAGNET IN PLACE
1kΩ
MODEL MSS-321S-002
LOOP
BLK
CLOSED
WHT
LOOP
WHT
OPEN
RED
LOOP
RED
CLOSED
BLK
1kΩ
LOOP
BLK
CLOSED
WHT
1kΩ
LOOP
WHT
OPEN
RED
LOOP
RED
A
CONTACT STATE SHOWN WITH MAGNET IN PLACE
CLOSED
BLK
LOOP
BLK
CLOSED
WHT
LOOP
WHT
MODEL MSS-321S
CONTACT STATE SHOWN WITH MAGNET IN PLACE
OPEN
RED
LOOP
RED
CLOSED
BLK
LOOP
BLK
OPEN
WHT
LOOP
WHT
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-310S
MODEL MSS-311S
End-Of-Line Resistor Custom Models ( -i#-#-#-#-#-# suffix)
i#-#-#-#-#-# Scheme:
"-i" precedes custom resistor (kΩ)
values separated by hyphens. The
sequence of entries correlates to the
positions depicted in the key. "N" is
used as a null place-holder (No resistor
for this position). Contact Magnasphere
for nomenclature guidance and for
resistor value availability.
CLOSED
BLK
LOOP
BLK
CONTACT FORM DEFINED BY INFIX
2
4
RESISTOR POSITION KEY
6
CONTACT FORM DEFINED BY INFIX
MSS-3##S-003
CONTACT FORM DEFINED BY INFIX
BLK
BLK
WHT
WHT
1kΩ
RED
RED
MSS-3##S-003:
Series 1k resistor on
Circuit
Circuit A. One instance
A
shown at right:
Circuit
B
Circuit
C
MSS-3## -004:
S
Series 1k resistor on
Circuit
BLK
1kΩ
BLK
WHT
1kΩ
MSS-3##S-004
WHT
RED
RED
Examples:
1
3
5
MSS-321S
Circuit
BLK
-i.18-.3-1-N-N-1
A
BLK
At right.
MSS-330S
Circuit
WHT
B
-i1-N-1-N-N-N
WHT
as an alternate ID
Circuit
RED
to MSS-330S-004,
C
RED
last to the right.
Circuit A and on Circuit
A
B. One instance shown
at right:
Circuit
B
Circuit
C
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-321S
-i.18-.3-1-N-N-1
300Ω
1kΩ
180Ω
BLK
BLK
WHT
1kΩ
WHT
RED
RED
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-321S-003
CONTACT STATE SHOWN WITH MAGNET IN PLACE
MODEL MSS-330S-004
CONTACT STATE SHOWN WITH MAGNET IN PLACE
CLOSED
LOOP
CLOSED
LOOP
OPEN
MODEL MSS-330S-004
LOOP
or MSS-330S-i1-N-1-N-N-N
CLOSED
BLK
1kΩ
LOOP
BLK
CLOSED
WHT
LOOP
WHT
OPEN
RED
LOOP
RED
CLOSED
BLK
1kΩ
LOOP
BLK
CLOSED
WHT
LOOP
WHT
OPEN
RED
LOOP
RED
CLOSED
BLK
1kΩ
LOOP
BLK
CLOSED
WHT
1kΩ
LOOP
WHT
CLOSED
RED
LOOP
RED
Loading...