Magnadyne X11 User Manual

Owner’s

Manual

Model: X11

For Technical Assistance, please call [phone],

or visit www.magnadyne.com

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Remote Control Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Quick Reference

LCD Transmitter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Chirp Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parking Light Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

System Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Security Operation

Active Arming: Lock and Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Manual Disarming: Unlock and Disarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Remote Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Vehicle Locator System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Panic Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Trigger the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Anti-Car Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

System Status Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Driver LCD Transmitter Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Dome Light Supervision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Ignition Controlled Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Channel 3 Trunk Release Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Channel 4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Channel 5 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Channel 6 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Channel 7 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Remote Starter Operation

User Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

How to Remote Start Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

How to Operate the Vehicle While Running on Remote Start . . . . . . . . . . . . . . . . . . . . . 15

Quick Stop Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Timer Starting Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Turn Off Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Shut Down Input for Remote Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Turbo Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Remote LCD Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Programming the LCD Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20

Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Replacement Parts Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2

2-Way
LCD
Remote

1-Way
Backup
Remote

HOOD

TRUNK

ARM

IGN

2-Way
LCD
Remote

LCD
Display
Icons

Introduction

Congratulations on your purchase of a quality Marksman automotive security and remote start
system. Marksman security products have been designed to provide the consumer with a
technologically superior product with years of trouble free operation. The information enclosed will
provide a ready reference of the operation and maintenance of your new Marksman security and
remote start system.

Remote Control Transmitters

The LCD screen on the remote control displays graphic icons. It provides you visual information on
any trigger of the sensors and around the clock surveillance to your vehicle as well as showing the
present status of the system.

Battery Replacement

The two-way LCD remote control is powered by a 1.5V type AAA high power digital camera battery.
When the power of the battery weakens 3 things will happen to indicate a low battery.

1. All the LCD icons on the display will turn off and only the battery icon will be flashing.

2. The two-way reporting function will turn off to preserve remaining battery power until a
replacement battery is installed.

3. When the buttons on the transmitter are pressed you will hear 3 beeps.

When the old battery is replaced with a new one, there will be a melody playing to indicate the
power is up and the clock on the LCD screen returns to AM12:00 after displaying all the icons.
Correct the time by pressing SET for 3 seconds before using.
Note: Even if the battery is replaced, your programmed set values shall remain unchanged. The
remote control automatically reads and memorizes all the previous set information saved in the
main control module.

Press the button two times
when the battery compartment
is empty, then insert the new
battery.

3

LCD Transmitter Operation

Transmitter Button

-

-

-

-

-

Hold for 3

Seconds

+

Hold for 2

+

Seconds

-

-

System Function Remark

Locks Doors & Arms System

Arm and Bypass the 2 Stage

Shock Sensor (Zone 4)

Arm and Bypass the 2nd

Sensor (Zone 6)

Arm and Bypass

Sensor 1 and 2

Arm and Activate Hidden Alarm Function Press within 3 Seconds

Car Locator Wait for 30 Seconds After Arming

Remote Panic Function Press and Hold for 3 Seconds

Silent Arming/Disarming Ignition in “OFF” Position

Active Anti-Car Jacking Mode

Unlock Doors & Disarm Alarm

Two Step Door Unlock &Disarm Alarm Press Unlock Twice within 3 Seconds

Trunk Release (Channel #3) Press and Hold for 1.5 Seconds

Automatic Arming Bypass Alarm Must be in Disarmed Mode

Press Twice within 3 Seconds

Press within 5 Seconds

Press within 5 Seconds

Ignition in “ON” Position,

Press and Hold for 2 Seconds

-

+

+

+

+

- +

4

Activate or Turn Off the Remote Start Press Twice within 3 Seconds

Channel #4 Output (4)

Channel #5 Output (5)

Channel #6 Output (6)

Channel #7 Output (7)

Switch Transmitter Operation

to the Second Car/System

Press Together and Release

Press Together and Release

Press Together and Release

Press Together and Release

Press and Release trunk, Then press Lock-

Unlock Together

LCD Display Transmitter Operations

Transmitter Button

-

SET

-

-

SET SET

-=

SET

-=

SET

System Function Remark

System Trigger Record Check Press within 3 Seconds

System Status Check

Optional Driving Pager

Monitor Interior Temperature

Press within 3 Seconds

Press within 3 Seconds

Press within 3 Seconds

Chirp Indicators

Chirp Function

1 Chirp System is Armed
2 Chirps System is Disarmed
3 Chirps Defective Sensor of Open Door Reminder
4 Chirps Disarm / Previously Triggered
2, 3, 6 Chirps Car Locator

Parking Light

Flash Function

1 Flash System is Armed
2 Flashes System is Disarmed
3 Flashes Disarmed / Triggered
2 - 3 - 6 Flashes Car Locator
Constant On Engine Running Under Remote Start (Default Setting)

5

LED Display

LED Function

OFF System is Disarmed
Slow Flashing System is Armed
Fast Flashing System in Passive Arming
On Solid System in Valet Mode
1 Flash - Pause Zone 1, Trigger for Hood
2 Flashes - Pause Zone 2, Trigger on Trunk
3 Flashes - Pause Zone 3, Trigger on Door Switch
4 Flashes - Pause Zone 4, Trigger on Sensor #1
5 Flashes - Pause Zone 5, Trigger on Ignition Switch
6 Flashes - Pause Zone 6, Trigger on Sensor #2

System Characteristics

Siren/Horn Parking Light LED Doors Starter Dome Light

1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking Disabled

2. Disarming 2 to 4 Chirps 2 or 3 Flashes Unlocking

3. Trigger Alarming Flashing Pause Flash Disabled Flashes

4. Panic Alarming Flashing Flashes

5.Car
Jacking

6

Alarming Flashing Disabled Flashes

Turns on for

30 Seconds

Manual Arming: Lock and Arm

ARM ARM

HOOD

TRUNK

ARM

System Armed

Door Ajar

Trunk/Hood Ajar

1.Press the button on the transmitter.

2.The siren will chirp once and parking lights will flash once indicating that the system is now
armed. The vehicle door will lock upon arming when interfaced with the security system.

Clear the Flash Icon:

Press the SET button 3 times
within 3 seconds to clear the
flash icon on the LCD screen
transmitter.

Door Ajar / Defective Sensor Reminder

If the siren sounds 3 times, there is a Door, Trunk, or Hood left open.

Silent Arming/Disarming

Pressing the transmitter and button at the same time will arm or disarm your security
system, No chirp sound will be heard, arm/disarm confirmation will be through the vehicles
parking lights only.

Shock Sensor Bypass (Sensor #1)

Press the button on the transmitter two times within 3 seconds. This will arm the security
system and bypass the shock sensor.

Sensor Bypass (Sensor #2)

Press the button first, within 3 seconds, press the button on the transmitter. This will arm
the security system and bypass the #2 sensor.

All Sensor Bypass (Sensor #1 and #2)

Press the button first, within 3 seconds, press the button on the transmitter (2) times. This
will arm the security system and bypass both electronic sensor ports.

Notes on Remote Sensor Bypass: The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming cycle.

Automatic Arming

(Applies only when Automatic Arming is Programmed On)

This security system is equipped with an optional automatic arming feature which allows the
security system to arm 30 seconds after the last door is closed. Operation is as follows:

1. Turn the ignition to the “OFF” position and exit the vehicle.

2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you re­open any protected entrance, the security system LED will stop flashing. It will begin flashing
again once the vehicles entrances are closed.

3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The
siren/horn will chirp once and the parking lights will flash once.

7

System Disarmed

Door Triggered

Trunk/Hood Triggered

HOOD

TRUNK

IGN

Shock Sensor

Triggered

Ignition Triggered

Automatic Arming: Lock and Arm

(continued)

Automatic Arming with Passive Door Locking

(Additional programming required)

The vehicle doors will automatically lock after the automatic arming cycle has been completed.

Automatic Arming Bypass

While the system is in disarmed mode, press the button twice. The horn/siren will respond
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as
long as you wish. To exit this mode press the or buttons and the system will return to normal
status.

Disarming: Unlock and Disarm

1. Press the button on the transmitter.

2. The siren will chirp twice and parking lights will flash twice indicating that the system is now
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon
disarming when interfaced with the security system.

Clear the Flash Icon:

Press the “SET” button 3 times within 3 seconds will
clear the flash icon on the LCD screen transmitter.

Tamper Disarming

If the security system was triggered, upon disarm, the siren will chirp 4 times and parking lights
will flash 3 times.

Pathway Illumination

This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds
upon the lock signal.

8

(Must be Programmed On)

Disarming: Unlock and Disarm

Remote Door

Lock

HOOD

Remote Door

Unlock

(continued)

Two Steps Door Unlock

(Additional Wiring Required)

This feature will independently unlock the drivers door only when disarming the security
system. Pushing the button a second time within 3 seconds will unlock the other doors.

Automatic Rearm

(Must be Programmed On)

If this feature is selected, the security system will automatically rearm itself within 60 seconds
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened
before the 60 second timer is up.

Disarming without a Transmitter

The override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).

2. Within 10 seconds push and release the valet switch, the alarm will stop sounding and enter

the disarm mode. You can now start and operate the vehicle normally.

Remote Valet Mode

(System in Disarm or Valet Mode)

The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm functions and remote start functions are bypassed, however the remote panic feature and
remote door locks will remain operational. To use the valet mode, the system must first be
disarmed either by using your remote transmitter, or by operating the manual override sequence.

Enter the Valet Mode:

1. While in disarmed mode, turn the ignition to “Off”
position and open the drivers door.

2. Push and hold the and buttons until the
door locks cycle “Lock/Unlock”. The LED will will
flash every 5 seconds while the unit is in the valet
mode.

Exit the Valet Mode:

1. While in disarmed mode, turn the ignition to “Off” position and open the drivers door.

2. Push and hold the and buttons until the door locks cycle “Lock/Unlock”.

The LED will will be off indicating the alarm is out of the valet mode.

9

Progressive Remote Vehicle Locator System

Doors

Triggered

Ignition

Triggered

ARM

IGN

ARMARM

HOOD

TRUNK

ARM

Trunk / Hood

Triggered

Warn Away

Triggered

Shock Sensor

Triggered

Note: The remote vehicle location system is active 30 seconds after the alarm is armed.

1. Press the button to active the vehicle locator system. The horn/siren will beep 2 times and
the parking lights will flash 3 times. This operation will repeat a second time.

2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parking
lights will flash 3 times. This operation will repeat a second time.

3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parking
lights will flash 6 times.

Remote Panic Function

The transmitter can be used as a remote panic switch to manually trigger the alarm system in case
of an emergency.

1. Press and hold the button for 3 seconds. The security system will begin to sound and the
parking lights will begin to flash. The icon will display in the LCD transmitter display.

2. During panic mode, the normal functions of this transmitter becomes temporarily inoperable.
The transmitter and buttons can be used to lock and unlock the door (if the option is
installed), however, once the button is pressed, the vehicle’s starter disable device, will be
enabled allowing the vehicle to start.

3. To stop the panic alarm, press the transmitter button , the panic mode will be turned off
immediately.

4. If the button is not pressed, the alarm will automatically stop after 30 seconds.

Trigger the System

When armed, your vehicle is protected as follows:

1. Light impact will trigger the warn-away signal.

2. Heavy impacts, doors open, hood open, trunk open or ignition key activated will trigger the
programmed sequence. The starter disable relay prevents the vehicle’s starter from cranking.
The siren, horn, parking lights and dome light will turn on to alert of an intrusion for 30
seconds. If one of the sensors or detectors are still active, the security system will sound a
maximum of 6 times for 30 seconds.

10

Trigger the System

LCD Transmitter Melody Sound

When the Security System is triggered, it will alert the user with flashing icons on the LCD Display
and audible melody sound. To stop the melody sound, press any button on the LCD transmitter.

LCD Transmitter Clear the Flash Icon and Melody Sound

When the Security System is triggered, the LCD screen will alert the user through melody sound
and flashing icons. By pressing the “SET” button 3 times within 3 seconds it will clear the flashing
icons and stop the melody sound.

Noise Abatement

The X11 security system has a built-in Noise Abatement Circuit that prevents annoying, repetitive
false alarms by filtering out environmental conditions. If the security system is triggered more
than five times by the same sensor , the circuit will interpret this as a false alarm and ignores, or
bypasses that switch or sensor.

The Noise Abatement Circuit monitors doors, hood and trunk switches differently. If the security
system is triggered by one of these switches for three cycles, the switch will be bypassed until the
trigger ceases.

(continued)

Anti-Car Jacking

Warning: The anti-car jacking feature default setting is “OFF”. Have your installation facility enable
this feature if you feel it is needed.

Manual Anti-Car Jacking

1. Press and hold the transmitter and buttons at the same time for 2 seconds while the
vehicle’s ignition is “ON” and all doors are closed. The parking lights will turn on for 1.5
seconds to indicate the anti-car jacking protection is armed.

2. Once the system is armed, if you are forced from your vehicle, the system will trigger when the
door is opened and closed while the ignition is “ON”.

Passive Anti-Car Jacking

1. Close all entrances first then turn the ignition switch to the “ON” position, the anti-car jacking
system will arm.

2. Once the system is armed, if you are forced from your vehicle, the system will trigger when the
door is opened and closed while the ignition is “ON”.

11

Anti-Car Jacking

HOOD

TRUNK

ARM

IGN

(continued)

Trigger the Anti-Car Jacking Mode

Three Timer circuits will function as follows:

First Timer Circuit

1. 50 seconds after the car jacking mode has been activated, the siren will begin to sound for 15
seconds.

2. During the 15 second activation period, you will be alerted to push the valet switch once to
turn off the car jacking feature.

3. If by now the valet switch has not been pushed, it will enter the second timer circuit.

Second Timer Circuit

65 seconds after the system has been triggered, the siren starts sounding and the parking lights
start flashing.

Third Timer Circuit

90 seconds after the security system has been triggered:

1. The vehicles siren is still sounding, parking light are flashing

2. The starter disable mode will activate to prevent the vehicle from starting

3. It will remain active until the vehicles battery power is exhausted

Override the System to Turn Off Anti-Car Jacking

Turn the ignition switch from OFF to ON and within 10 seconds, push the valet switch. The siren
will stop sounding and the security system is now disarmed.

Status Checking (LCD Transmitter Only)

System Check

When you want to check the security systems present status through the transmitter LCD, press the
transmitter “SET” button twice, within three seconds press the button. The security system
responds with one melody sound and the LCD screen should be illuminated.
Note: If there is no response from the LCD transmitter, you may be out of range to receive the
signal.

System Trigger Check

Press the transmitter “SET” button first, within three seconds press the

button. The transmitter will respond with one melody sound and all

trigger records will immediately displayed on the transmitter LCD screen.

12

Driver LCD Transmitter Paging

It is useful in the event that someone wants to page the driver of the parked vehicle. (Optional)

Inside the Vehicle Paging

With the ignition switch in the "OFF" position, press the valet switch for 2 seconds to page the
driver. One chirp will sound from the vehicle and the LCD transmitter will begin to sound with a
melody. The icon will then appear on the LCD transmitter to confirm this function.

Outside the Vehicle Paging

To page the drive of the vehicle, "Knock" on the windshield glass to activate the LCD transmitter
with a melody sound. The icon will then appear on the LCD screen (only when the optional
knock sensor, Model # M10-Page, is installed).

1. Turn on the vehicle paging sensor. Press the SET button on the LCD transmitter, within 3
seconds, press the button to activate the driver paging sensor. The vehicle will then
respond with chirps from the horn/siren and a melody sound from the LCD transmitter. The

icon will then appear on the LCD transmitter screen.

2. When the windshield knock sensor is activated, the vehicle will then respond with chirps from
the horn/siren and a melody sound from the LCD transmitter. The icon will then appear on
the LCD transmitter screen.

3. When the driver of the vehicle unlocks the doors using the remote, the driver paging system
will turn off.

(Optional and Requires Glass Mount Knock Sensor)

Dome Light Supervision

The Security System has a unique feature which will control your vehicle’s dome light.

1. Upon disarming the vehicle security system, the interior dome light will come on and remain
remain on for thirty seconds.

2. When the vehicle security system is triggered, the dome light will flash for the same duration
as the horn/siren pulses.

Ignition Controlled Door Locks

If the vehicles door locks have been interfaced with the security system, the system will
automatically lock the vehicle’s doors when the ignition key is turned to the “ON” position and or
unlock the doors when ignition key is turned to the “OFF” position. The doors must be closed.

Channel 3: Trunk Release Output

Press and hold the button for 1.5 seconds to activate the trunk release (Channel 3 output)
and/or any other devices connected.

Channel 4 Output

Press and hold the and button at the same time to activate the Channel 4 output.

13

Channel 5 Output

Press and hold the and button at the same time to activate the Channel 5 output.

Channel 6 Output

Press and hold the and button at the same time to activate the Channel 6 output.

Channel 7 Output: (Default Setting = Defrost Control)

Press and hold the and button at the same time to activate the Channel 7 output.
Note: If Channel 7 has been programmed for defrost operation it will not function from the transmitter.

14

Remote Start Operation

User Warnings

As with any product that performs automatic functions, there are certain safety precautions that
you must practice and be aware of.

1. Keep the transmitter out of reach of children.
DO NOT leave anyone in the vehicle while running on remote control.

2.

3. Alert any service personal that the vehicle can be started automatically.

4. DO NOT start the vehicle by remote while it’s in an enclosed area or garage.

5. Always apply the parking brake and lock the vehicle as you exit the vehicle.

6. Should the unit malfunction, disconnect the fuse until the problem is corrected.

7. The use and operations of this security system is the sole responsibility of the
owner/operator of the vehicle.

8. Some areas may have local ordinances that prohibit leaving a vehicle running on public
streets. Check your local laws and ordinances.

To Remote Start Your Vehicle by Using the Remote Transmitter

1. Press the button twice on the remote transmitter.

2. The parking lights will turn “ON” to indicate the remote start command has been received.

3. The engine will start in approximately 5 seconds.

4. Once the engine is running, the parking lights will turn back on to indicate climate controls are
activated to your presettings (While the vehicle is running, the “minute” digits will appear
flashing on the LCD screen of the transmitter. It will indicate the count down timer based on
the 5, 10, 20 or 30 minute run time set up by your installation center).

5. The vehicle will run for 5 to 30 minute cycles and automatically shut down (When the unit
shuts off the count down timer will turn off and the transmitter will play a melody tune).

Note: The Remote Start unit will not start if any of these conditions exist:

1. The hood is opened.

2. The brake pedal is pressed.

3. Move the optional remote start enable toggle switch to “OFF” position (if installed).

4. The gear selector is in any gear other than “Park” or “Neutral”.

Safe Start

The factory default setting to remote start your vehicle is to press the button twice. If the child
safety mode has been activated, press the and the buttons at the same time to remote start
the vehicle.

To Operate the Vehicle While in the Remote Start Feature

1. Insert the Ignition key, turn it to the “ON” position “NOT THE START POSITION”.

2. Press the brake pedal.

Note: If the Brake Pedal is pressed before the key is in the “ON” position, the engine will
automatically shut off.

(Child Safety Mode):

15

Remote Start Operation

Quick Stop Feature

This feature allows the vehicle to remain running after the key has been removed from the
ignition. This feature is useful for occasions when you wish to exit and lock/arm the vehicle for
short periods of time. This will keep the engine running for climate controls to stay on.

1. Before turning the engine off with the ignition key, press the button twice. The LED will flash
three times to indicate the feature is activated.

2. Turn the ignition key to the “OFF” position (the engine will stay running).

3. The engine will run until the pre-programmed run time elapsed or a shutdown input is
received.

Timer Starting Modes

The X11 can be programmed to start and run the engine every 3, 2 or 1 hours by time or by
temperature. The X11 can also be set to punctually start the engine at the same time the next day.
In all modes, the engine will run for the pre-set time (Default setting is 10 minutes) running time
and then shut down the same as if it were being controlled by the remote transmitter.

Important! Timer starting should be used only in open areas. Never start, or most importantly
leave a vehicle running in an enclosed area.

3, 2 or 1 Hour Timer Start without Temperature Control: (Default Setting is 3 Hours)

This feature is designed for extreme cold climate usage. The system will auto start the vehicle
every three hours to prevent the engine from freezing and creating a hard-to-start condition.

3, 2 or 1 Hour Temperature Starting Control: (Default Setting is 3 Hours)

The system can be programmed to automatically start the vehicle’s engine whenever the
temperature inside the vehicle reaches and/or drops below a preprogrammed temperature level.
The X11 system will check the interior temperature ever 3,2 or 1 hour.

Hourly Timer Start: (Runs Every 3, 2, or 1 Hours Depending on Programming)

Press the button first, within three seconds press the button. The parking lights will flash
six times and the siren/horn will sound six times. The vehicle is now in timer start mode.
Note: The hourly timer start function requires additional programming of the LCD remote
transmitter. (See Timer Setting page 20 for programming).

Daily Timer Start:

Press the button first, within three seconds press and hold the button for 3 seconds. The
parking lights will flash six times and the siren/horn will sound six times. The vehicle is now
programmed to start at the same time tomorrow (next day).

Note: The daily timer start function requires additional programming of the LCD remote

transmitter. (See Timer Setting page 20 for programming).

(continued)

Exit the Timer Start:

To Cancel the timer start function, do one of the following:

1. Start the vehicle manually using the ignition key.

2. Remote start the vehicle using your remote transmitter.

16

Turn Off Remote Start

When the engine is running by remote start and you wish to stop the engine from running:

1. Press the button twice on the remote transmitter.

2. Move the optional remote start toggle switch to the “OFF” position (if installed).

3. Press the vehicle’s brake pedal, the engine will stop running and the parking lights turn off to
indicate the engine has stopped.

Shut Down Input for Remote Starter

If any of the following conditions exist while the system is operating, the engine will not start or will
shut down immediately:

1. The hood is opened.

2. The brake pedal is pressed.

3. The hand brake is released (for Standard Transmission vehicles only).

4. Engine is over-RPM (Tachometer Checking Type only).

5. The preprogrammed run time (5/10/20/30 minutes) has elapsed.

6. Press the button twice on the remote transmitter under Remote Start Mode.

7. Move the optional remote start enable toggle switch to “OFF” position (if installed).

8. The vehicle refused to start running after 3 unsuccessful attempts.

Turbo Timer Mode

Turbo Timer Mode keeps the engine running after arriving at you destination for a programmable
time period of 3, 5 or 10 minutes. This allows the system’s time to conveniently cool down the
turbo charger after you have left the vehicle.

To Activate:

1. While the engine is running, set the emergency brake and place the transmission to "Park".

2. Before turning off the engine, press and release and buttons at the same time. The light
will flash to indicate the remote start has entered Turbo Timer Mode.

3. Remove the ignition key from the key cylinder. The engine will keep running.

4. Exit and secure the vehicle. The engine continues running until the preprogrammed time has
elapsed.

(Also See Installation Manual)

Interference

Note: The transmission range may become shorter if the system is interfered by a stronger radio
frequency from sources of high voltage electric power or obstacles like tall buildings. The
transmitter uses low output powered frequency.

17

Remote LCD Icons

Armed Mode

Vehicle is in armed mode

Car Jack Mode

Car jacking mode is activated

Remote Transmission

You are transmitting the signal to
the control unit

Hood Trigger

Hood is illegally opened (Zone 1)

Trunk Trigger

Trunk is illegally opened (Zone 2)

Door Open Warning

Doors are illegally opened
(Zone 3)

Ignition Trigger

Ignition switch is illegally turned
on (Zone 5)

System Trigger

Engine Cranking

Your vehicle’s engine is cranking
by remote control

Timer Control Start

Engine start automatically at the
same time next day or 2/3 hours.

Time Monitor

Count Down Timer

Reminder when time
is up for parking

Melody Mode

Remote control alert user
through melody sound

Button Lock

Disable the transmission
function temporarily

Temperature Monitor

Indoor temperature of your

18

vehicle

Hidden Alarm Mode

Your vehicle is in armed with
hidden alarm mode

Valet Mode

All the function shall be
temporarily on hold

In-Range Indicator

You are within the remote
control range

Sensor Trigger

Trigger on sensor 1 (zone 4) or
optional sensor 2 (zone 6)

Warn Away Trigger

Warn away trigger on sensor 1
or optional sensor 2

Low Battery

You have to replace the remote
controls battery

Engine Running

Your vehicle’s engine is running

Alarm Alert

You have set morning
alarm call

Power Save Mode

Saves the battery power

Vibration Mode

Remote control vibrates when
the system is triggered

Driver Paging

Someone is paging you in front
of your vehicle

Channel #3 is Activated

Channel #4 is Activated

Channel #5 is Activated

Channel #6 is Activated

Channel #7 is Activated

Programming the LCD Transmitter

Button Description Operation

SET

SET

SET

SET (3X) Clear the Flash Icon and Melody Sound Press within 3 Seconds

SET & LOCK Button Lock Enabled/Disabled Press within 3 Seconds

SET & UNLOCK Melody/Vibrate Mode Press within 3 Seconds

+

SET (10 m, 20 m, 30 m, 1 hr, 1.5 hr, 2 hr) Leave the Buttons Starting Count

+

SET

SET - SET -

SET -

Screen Lamp On

Press and hold the “SET” button one second, with the melody sound and the LCD screen lamp
will turn on for 5 seconds.

LCD Screen Lamp Turns ON for Press and Hold for 1 Second
Five Seconds 1 Melody Sounds to Confirm

Timer Programming Mode

Power Save Mode

on the LCD Screen

Program Count Down Timer Press within 3 Second Cycles

Enable/Disable Beep Sound While
Pressing Button

Display Illumination On/Off 3 Seconds between “SET - SET”

Switch Between 1st Car RF Control and

+

2nd Car RF Control

Press and Hold for 3 Seconds
2 Melody Sounds to Confirm

Press and Hold for 5 Seconds
1 Melody Sounds to Confirm

Down then Timer Icon Flashes

Press for 2 Seconds

and Hold for 2 Seconds

+

Hold for 2 Seconds

Power Save Mode

While in the Power Save Mode, the LCD transmitter uses “0” current to save the battery power.

1. Press and hold the “SET” button for 5 seconds. One melody will sound from the transmitter
and the LCD will show “SAVE”. You are now in the Power Save Mode.

2. Under the Active Arming Mode and Disarm Mode. Turn the ignition switch to the “ON” position.
The LCD remote transmitter will automatically enter the Power Save Mode.

Exit Power Save Mode

Press any button on the LCD transmitter to exit the Power Save Mode.

Clear the Flash Icon and Melody Sound

Press the SET button 3 times within 3 seconds and it will clear the flashing icon and melody
sound on the LCD transmitter.

19

Programming of the LCD Transmitter

Stop the Trigger Melody

While triggering the alarm, the LCD screen will alert the user through melody sound and flashing
trigger icon. Press any button on the transmitter to stop melody sound only.

Button Lock

Use this mode to disable the transmission function of the remote control temporarily to prevent
any inadvertent pressing of buttons.

1. Press the “SET” button first, within 3 seconds press and hold the button for 2 seconds to
activate or cancel the button lock function. The icon will be displayed on the LCD screen
to show button lock mode.

Vibration/Melody Mode

This mode is useful when you are in a noisy place and it is difficult to hear the beep from the
remote. The LCD transmitter will vibrate if your security system has been activated.

Press the “SET” button first, within 3 seconds press the ( ) button for 2 seconds to select
the mode of vibrate/melody. The icon will be displayed on the LCD screen to show mode.

Set-Up Fixed Count Down Timer

Press the “SET” button first, then within 3 seconds press and hold the button for 2 seconds.
The LCD screen will show the icon and timer (0:10). Press the button again to choose the
desired time.
Note: 1. The countdown periods are fixed at 10 minutes, 20 minutes, 30 minutes, 1 hour, 1.5

hours and 2 hours maximum.

Note: 2. Press the SET button for a real time indication of the remaining time left.
Note: 3. When the display is showing 0:00, the timer is off

Out of Range Indication

1. If the transmitter is within range, the icon will display on the LCD screen.

2. If you are out of range, the icon will disappear from LCD Screen and transmitter will beep 5
times.

20

Clock and Timer Setting

Step

1

2

3

4

5

6

7

8

10

Note: Any adjustment requires starting at the beginning (Step 1) and following the steps until you
reach the one that corresponds with the description/function you want to program.

For instance, if you are trying to set the Alert Alarm Setting ON/OFF (the description that
corresponds with Step 5) you must follow steps 1-5 in order for it to be set.

Button Description Operation

Press and Hold SET

Button for 3 Seconds

Press the SET

Button Once

Press the SET

Button Once

Press the SET

Button Once

Press the SET

Button Once

Press the SET

Button Once

Press the SET

Button Once

Press the SET

Button Once

Press and Hold

Button for 2 Seconds

Count Down Timer Setting (Hour) Flash

Count Down Timer Setting (Min.) Flash

Flash / Icon and Hours for Adjusting

Time Setting (Hour)

Flash Digit for Adjusting

Time Setting (Min.)

Flash Digit for Adjusting

Alert Alarm Time Setting (Hour) Flash

Digit for Adjusting

Alert Alarm Time Setting (Min.) Flash

Digit for Adjusting

Alert Alarm Setting ON/OFF for (-) and (+)

Digit for Adjusting

(Max 19 Hrs. 59 Min.)

Digit for Adjusting

Count Down Timer Setting ON/OFF for (OFF) and (ON)

Daily Timer Start Timer Setting

for (-) and (+)

for (-) and (+)

for (-) and (+)

for (-) and (+)

for (-) and (+)

for (-) and (+)

for (-) and (+)

21

Replacement Parts

TRANSMITTERS DESCRIPTION MODEL # PRICE

5-Button Transmitter for
X11 Security System X11RF-LCD $139.95 ea.

4-Button Transmitter for
X11 Security System X11RF 59.95 ea.

BATTERIES

**1.5 Volt AAA Lithium Battery Highly

Recommended

*1.5 Volt AAA High Capacity Digital

Camera Battery Suggested

1.5 Volt AAA Alkaline Battery Minimum

CR2032 - 3 Volt Lithium Battery (2 pcs.)

Models:

Radio Shack: #23-162
Duracell: #DL2032
Eveready: #ECR2032
Panasonic: # CR2032

22

Parts Order Form

Credit Card or Money Order Only

(Sorry No Cash, C.O.D. or personal checks accepted)

SHIP TO: (No P.O. Boxes)

LAST NAME FIRST NAME INITIAL

STREET ADDRESS

ADDITIONAL ADDRESS

ADDITIONAL ADDRESS

CITY STATE ZIP CODE

DAY TIME PHONE NUMBER

PAR

T # DESCRIPTION

QTY. PRICE EACH TOTAL

Sales Subtotal = ________ . ______

California Residents Add Sales Tax = ________ . ______

Shipping and Handling (See Chart) = ________ . ______

TOTAL = ________ . ______

On regular orders please allow 4-5 weeks for delivery.

Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.

If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.

CREDIT CARD INFORMATION

CREDIT CARD N0.

EXPIRATION DATE

CARD HOLDER’S LAST NAME FIRST NAME INITIAL

STREET ADDRESS

CITY STATE ZIP CODE

Mail to: Magnadyne Corporation

ATTN: Consumer Parts Sales
P.O. Box 5365
Carson, CA 90749-5365

Shipping and Handling

Up to $20.00 $5.00

20.01 to 30.00 5.95

30.01 to 45.00 6.50

45.01 to 70.00 6.95
Over 70.01 7.95

VISA
MC

Call: [phone] Fax: [phone]

23

Limited Lifetime Warranty

Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the correct
power requirements designated for the specific product. This warranty and Magnadyne Corporation
or its authorized agents obligations, hereunder do not apply where the product was: damaged while
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably
maintained, utilized in commercial or industrial operation, or serviced by anyone other than
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its
authorized agents do not assume any labor costs for the removal and reinstallation of any product
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized
agents. Such costs are the sole responsibility of the purchaser.

This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories
used in connection with the product resulting from improper installation, alteration, accident,
misuse, abuse or acts of nature.

This Limited Life Time Warranty applies only to the receiver section of the security system. Neither
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness
or any accessory item are covered by our standard 12 month limited warranty.

Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential
or incidental damages or claims that may arise due to failure of product to operate properly
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,
replacement of the product as stated above if all conditions of the warranty are met. No
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or
against the loss or damage to the contents of any vehicle in which a security system is installed.
Magnadyne security systems are only a deterrent against possible theft.

This warranty extends only to the original purchaser of the product and for the vehicle in which it
was originally installed. This warranty is not transferable or assignable to any person or vehicle.
Defective merchandise should be returned to the original point of purchase or secondly to
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must
be obtained before sending, or merchandise may be refused.

© Copyright 2008 Magnadyne Corporation

X11-UM 3-5-08 Rev. A