Please take the time to read all of the information in this manual. Familiarity with operation and installation procedures will help you obtain the best possible performance from your new AM/FM Stereo
Multi-Media Receiver.
WARNING! To prevent fire or electrical shock hazard, do not expose this product to moisture, or remove
cover or bottom screws. No user-serviceable parts inside. Refer servicing to qualified person
Index
Button Locations and Functions 3-4
Remote Control Button Locations and Functions 5
General Operation 6
Sound Controls 6-8
Speaker Selection 8
Setting the Clock 8-9
Sleep Timer Operation 9
Alarm Operation 10
Radio Operations 11-12
15. Play/Pause and Mute Button (ll):
Radio and Multimedia Input Modes: Press to mute volume level. Press again to restore.
Disc Mode: Press to pause disc play, press again to resume play.
IPOD Mode: Press to pause play, press again to resume play.
Bluetooth: Press to pause play, press again to resume play.
16. IPOD Selection Button: Press to choose IPOD input mode.
17. Seek Up (l) Buttons:
Radio Mode: Press to tune the radio to a higher frequency.
Disc Mode: Press to search for the beginning of next track or chapter.
IPOD Mode: Press to search for the beginning of the next track.
Bluetooth Mode: Press to search for the beginning of the next track.
18. USB/Disc Selection Button: Press to choose between Disc and USB modes.
19. Seek Down (l) Buttons:
Radio Mode: Press to tune the radio to a lower frequency.
Disc Mode: Press to search for the beginning or previous track or chapter.
IPOD Mode: Press to search for the beginning of the previous track.
Bluetooth Mode: Press to search for the beginning of the previous track.
20. Volume and Select Knob: Rotate to increase or decrease the volume level. Press to select the sound
controls: Bass, Treble and Balance.
21.AM/FM Radio Selection Button:Press to choose Radio mode. Sequential presses will select radio
front, Audio/Video input rear, Audio input rear or Bluetooth.
23.Audio/Video Input Jack: Press the AUX button until “AV IN F” appears in the display then plug in a
device via the 3.5mm audio/video input plug.
Note: The RV5090 does not control the device, it just allows the audio/video to be played through the
system.
24. Reset Button: Press to reset the unit to it’s default settings.
25. USB Input: Press the USB/DISC button until “DISC” appears in the display. Then plug in your USB
device. “USB” will then appear in the display.
Note: The RV5090 will control the USB audio device. (See “USB Input” for more details).
26. Speaker Selection Buttons (A, B and C): Switches the speaker sets on and off. Refer to the LED indi-
cators above the button to determine if the speaker set is on or off.
27. Bluetooth Indicator: Indicates Bluetooth status. (See “Bluetooth Operation” for more details).
28. Sleep Button (SLP): Sets the sleep timer. (See “Sleep Timer Operation” for more details).
29. Alarm Button (ALRM): Sets the alarm. (See “Alarm Operation” for more details).
30. Display Button (DISP): Press to display the clock or frequency in radio mode, track in music disc
mode, chapter and elapse time in movie disc mode or track in IPOD mode. Press and hold to perform
clock setting functions (See “Setting the Clock” for more details).
31. Radio AS/PS Button: Automatic radio station memory storing (AS) and Preset radio station scanning
(PS). (See “AM/FM Operation” for more details).
32. Equalizer and Loudness Button (EQ/LOUD): Press to select between the preset sound equalization
settings. Press and hold the button to boost high and low tones at low volume levels (loudness).
4
Remote Control Button Locations and Functions
POWER
VOL
TONE
MENU MODE
SETUP
1
2
3
4
VOL
5
VOL
DISP
6
RANDOM
REPEAT
7
8
EQ
BAND
AS/PS
ELAPSE
AUDIO
13
465
798
SUB.TT
9
10
11
12
EJECT
ENTER
ZOOM
SLOW
2
10/010
14
15
16
17
18
19
20
21
22
23
24
+
13
1. Power On/Off Button (
unit on or off.
): Press to turn the
2. Menu Button: Press to access the Menu screen
in movie mode.
3.Sound Control Button (VOL/TONE): Press to
select the sound controls: Bass, Treble and
Balance.
4.Setup Button: Displays the on-screen SETUP
menu.
5.Volume Buttons (VOL
to increase or VOL
s
/ VOL t): Press VOL s
t
decrease the volume level.
6.Display Button (DISP):Press to toggle through
the available display information.
7. Repeat Button:
Disc: Press to repeat a music disc track or to
repeat a movie disc title or chapter. Press
again to cancel.
8. Random Button:
Disc: Press to play all the tracks on the music disc
in random order. Press again to cancel.
9.Equalizer Button (EQ):Press to select between
the preset sound equalization settings. Press and
hold the button to boost high and low tones at
low volume levels (loudness).
10.Band Button: Press to select the radio mode.
Sequential presses will select radio band:
FM1, FM2, FM2 (MHz) and AM1, AM2 (KHz).
11. AS/PS Elapse Button:
Radio: Automatic radio station memory stor-
ing (AS) and Preset radio station scanning
(PS). (See “AM/FM Operation” for more
details).
Disc: Press to display movie information.
12. Audio Button:
audio/language setup.
13.Subtitle Button (SUB.TT):
movie disc’s subtitle languages.
Press to select appropriate movie
Press to access the
14. Eject Button ( ): Press to eject the disc.
15. Mode Button: Press to select between the
different modes: Radio, Disc, USB, Auxiliary
Input or Bluetooth .
16. Stop Button (): Press to stop disc play.
17. Play/Pause and Mute Button (): Press
to pause disc play, press again to resume play.
18. Backwards () or Fast Forward ()
Disc Play: Press
and “BACKWARD X 2”
appears in the display and the disc will play
backwards at 2 times the normal speed.
Press again and “BACKWARD X 4” will
appear. X8 and X20 speeds can also be
selected. Fast Forward
button works the
same way but fast forward. Press the ll
button at any time to resume normal play.
19. Enter Button: Executes the selected item.
20. Navigation Buttons (s, ,
t,
): Moves
feature selection up, down, left or right.
21. Down (l), Up (l) Buttons:
Radio Mode: Press to manually tune the radio
to a lower or higher frequency.
Disc Mode: Press to search for the beginning
or next track or chapter.
Bluetooth Mode: Press to search for the
beginning or next track.
22.Slow Button: Press to play the movie in slow
motion.
23.Zoom Button: Press to enlarge or reduce the
movie’s on-screen image.
To select a play source, press one of the following mode buttons:
AUX: Audio/Video Input Front (AV IN F),
Audio/Video Input Rear (AV IN R),
Audio Input Rear (AUX IN) or
Bluetooth (BT A2DP)
AM/FM: AM (KHz) or FM (Mhz) Radio Band (RADIO)
USB/DISC: Disc (DISC) or USB Input (USB)
i: IPOD Input (IPOD)
Dimming the Display:
Press the DIM button to select from the 4 levels
of brightness for the display area.
MHz
MHz
Display Selection:
Press the DISP button to display the clock.
Press again to return to previous display.
Press and hold to perform clock setting functions (See “Setting the Clock” for more details).
Sound Controls
Volume:
Increase the volume by rotating the VOLUME
knob clockwise. Decrease the volume by rotating
the Volume knob counterclockwise.
6
Sound Controls
Bass, Treble and Balance Control
Select the desired sound mode by pressing the VOLUME knob. The modes will be displayed in the following order: Bass, Treble, Balance and Volume.
Bass:
Select the Bass mode by pressing the VOLUME
knob. Increase the Bass by rotating the knob
clockwise. Decrease the Bass by rotating the
knob counterclockwise. After 6 seconds control
reverts back to volume control.
Treble:
Select the Treble mode by pressing the VOLUME
knob. Increase the Treble by rotating the knob
clockwise. Decrease the Treble by rotating the
knob counterclockwise. After 6 seconds control
reverts back to volume control.
Balance:
Select the Balance mode by pressing the VOLUME
knob. Adjust the Balance by rotating the knob.
-
R
L = Equal sound Right and Left
-
R 7 = Right speaker only
L 7 = Left speaker only
After 6 seconds control reverts back to volume
control.
Equalizer (EQ):
Press the EQ button to choose between the
preset equalizer settings: Normal, Classic, Rock,
Pop and Jazz as indicated in the display area.
Loud:
To boost high and low tones at low volume
levels, press and hold the EQ button until “LOUD
ON” appears in the display. To deselect, press
and hold the EQ button again until “LOUD OFF”
appears in the display.
Hold
7
Sound Controls (Continued)
Mute:
Press the MUTE button to mute the volume
level. Press the MUTE button again to restore the
volume.
Speaker Selection
Selecting Speaker Sets:
• Press the A button to toggle speaker set A on
and off. The LED above SPEAKER A lights up
when speaker set A is on.
• Press the B button to toggle speaker set A on
and off. The LED above SPEAKER B lights up
when speaker set B is on.
• Press the C button to toggle speaker set A on
and off. The LED above SPEAKER C lights up
when speaker set C is on.
Setting the Clock
1. Press the DISP button until the clock appears in
the display.
2. Press and hold the DISP button until the Hours
number starts flashing.
3. Rotate the VOLUME knob until the correct Hour
appears in the display.
Note: When setting the clock make sure to
select the correct AM or PM.
8
Hold
Setting the Clock (Continued)
4. Press the VOLUME knob and the Minute indica-
tors will start flashing.
5.
Rotate the VOLUME knob until the correct
Minutes appears in the display
and the colon between the hours and the minutes will start flashing indicating the clock is set.
. Wait 5 seconds
Sleep Timer Operation
Setting the Sleep Timer:
1. Press the SLP button and “SLEEP 10” appears
in the display.
2. Keep pressing the SLP button again until the
desired sleep time appears in the display (0,
10, 20, 30, 40, 50, 60, 70, 80 minutes).
3. Wait 5 seconds and the display will return to
normal operation and “SLEEP” will appear in
the display.
4.
After the designated sleep timer has expired
the unit will turn off automatically
Cancelling the Sleep Timer:
1. Press the SLP button until “0” is displayed.
2. Wait 5 seconds and the display will return to
normal operation.
.
9
Alarm Operation
Setting the Alarm Timer:
1. Press the ALM button and the clock will
appear in the display with the Hour number
flashing.
2.
Rotate the VOLUME knob until the correct Hour
appears in the display. “ALARM” will appear in
the display indicating the alarm is activated.
Note 1: When setting the alarm clock make
sure to select the correct AM or PM indicator.
Note 2: When setting the alarm DO NOT use
12:00 AM, because that time is used to cancel
the alarm.
3. Press the VOLUME knob and the Minute indi-
cators will start flashing.
4.
Rotate the
Minutes appears in the display
and the colon between the hours and the minutes will start flashing. “ALARM” will appear
in the display indicating the alarm is set.
VOLUME
knob until the correct
. Wait 5 seconds
5. Press the POWER button to turn the unit off.
The unit will automatically turn on when the
set alarm time is reached.
Cancelling the Alarm Timer:
Follow the procedures above except set the
alarm time to “A AM 12:00”. “ALARM” will disappear in the display indicating the alarm has
been cancelled.
10
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.